Loading ...
Sorry, an error occurred while loading the content.

Re: Vista issue? #1

Expand Messages
  • Brian
    That was easy enough...thanks! I thought I d tried that...guess not. Thanks!
    Message 1 of 4 , Jul 4, 2007
    • 0 Attachment
      That was easy enough...thanks! I thought I'd tried that...guess not.

      Thanks!


      --- In wuhu_software_group@yahoogroups.com, "wuhu_software"
      <wuhu_software@...> wrote:
      >
      >
      > When doing the below, do not hit Stop.
      >
      >
      > --- In wuhu_software_group@yahoogroups.com, "wuhu_software"
      > <wuhu_software@> wrote:
      > >
      > > Brian,
      > >
      > > I think I see the problem.
      > >
      > > Go in to tweaks, disable the rain sensor and wind sensors.
      > >
      > > Hit Ok.
      > >
      > > Wait until an update happens.
      > >
      > > Go back in to tweaks, then make your changes. Hit Ok.
      > >
      > > If starts working, do a reboot, let me know if the changes were not
      > > stored correctly.
      > >
      > >
      > >
      > > --- In wuhu_software_group@yahoogroups.com, "Brian" <yahoo@> wrote:
      > > >
      > > > Some of you may recall a couple months back my computer was
      > stolen.
      > > I
      > > > finally got it replaced with a new computer. This computer came
      > with
      > > > Vista so I am now working on setting up my system again, this
      > time
      > > in
      > > > a new platform. I have a WS2308 in direct serial mode.
      > > >
      > > > Since I did not have my console connected to a computer, I
      > decided
      > > to
      > > > disconnect my wind and rain sensor. At this point, I am looking to
      > > > just upload my temperature, barometer, and humidity.
      > > >
      > > > To do this, I've gone into Tweak Data and disabled rain and wind
      > > > sensors. This seems to work fine.
      > > >
      > > > Unfortunately, if I restart my computer, my settings change to
      > > > selecting "Disable all rainfall reporting" and unselecting the
      > > disable
      > > > rain and wind sensors. I had been playing with settings trying to
      > > get
      > > > it to work and I think that was one of the settings I had
      > selected
      > > in
      > > > an attempt. It seems the system wants to revert to these settings
      > > for
      > > > some reason.
      > > >
      > > > The problem I am having is by having the "disable all rainfall
      > > > reporting" selected instead of the other items, I cannot get the
      > > > console and computer to communicate (OFL data).
      > > >
      > > > When I attempt to change the settings back to what I want them to
      > > be,
      > > > I get an error message of "Rainfall data cannot be re-enabled
      > until
      > > at
      > > > least one update is received from the console. If Stopped, press
      > > Start
      > > > button and try again after an update has occurred." Unfortunately,
      > > > since my console and computer do not communicate under these
      > > settings,
      > > > I am unable to receive an update and basically cannot change the
      > > > settings. My standard fix has been to re-install wuhu each time
      > > (which
      > > > seems to reset the settings to what I need them to be).
      > > >
      > > > Is there a solution anyone can think of to remedy this?
      > > >
      > > > Thanks!
      > > >
      > > > Brian
      > > >
      > >
      >
    Your message has been successfully submitted and would be delivered to recipients shortly.