Loading ...
Sorry, an error occurred while loading the content.
 

Re: WS2316

Expand Messages
  • KNHBRIST1
    I know this may sound too simple, but I had it happen to me before on a phone line. The wire connectors on the end of the plug got bent and one was overlapping
    Message 1 of 7 , Sep 6, 2010
      I know this may sound too simple, but I had it happen to me before on a phone line. The wire connectors on the end of the plug got bent and one was overlapping and touching the other. To this day I have no clue how it happened as I just unplugged it and re-connected it later.
      Steve

      --- In wuhu_software_group@yahoogroups.com, "David" <davidmc36@...> wrote:
      >
      > Still nothing!
      >
      > --- In wuhu_software_group@yahoogroups.com, "David" <davidmc36@> wrote:
      > >
      > > Thanks for the info. I did a "reset" a couple of times by just removing the batteries and waiting for a bit to put them back in but that sounds like more of a "hard boot" if you will. I will definitely try the process you described on the weekend when I get back home.
      > >
      > > Cheers
      > >
      > > --- In wuhu_software_group@yahoogroups.com, Douglas Davis <electrix_blue@> wrote:
      > > >
      > > > Yeah David, I got the 2316U as well, seems if you ever unplug the unit from the
      > > > base station or it's power source, you have to completely reset the base station
      > > > and sensor. I had the same issue, when I moved as well, contacted Lacrosse, and
      > > > they said,
      > > >
      > > > * you have to first unplug all the wires from the outside sensor,
      > > > * then remove the batteries from both the sensor and the base station,
      > > > * wait for about 1 minute or so then replace the batteries.
      > > > * Then reset the base station to Factory Defaults, by simultaneously press and
      > > > hold the PRESSURE and WIND keys for 10 seconds.
      > > > * Then reenter the correct time, date and other settings for your base
      > > > station. You may have to in addition Press the PLUS(+) key for 2 seconds and a
      > > > short beep will sound to sync the base station to the sensor. ( I had to do this
      > > > to get the two units to talk to each other, after completing the above
      > > > steps..and it worked great.)
      > > >
      > > > Doug
      > > >
      > > >
      > > >
      > > > ________________________________
      > > > From: David <davidmc36@>
      > > > To: wuhu_software_group@yahoogroups.com
      > > > Sent: Wed, August 18, 2010 10:21:29 PM
      > > > Subject: [wuhu_software_group] Re: WS2316
      > > >
      > > >
      > > > Batteries are new in both, good alkaline ones too. Got me stumped.
      > > >
      > > > --- In wuhu_software_group@yahoogroups.com, Douglas Davis <electrix_blue@>
      > > > wrote:
      > > > >
      > > > > Try replacing the batteries, in both the sensor and the basestation..
      > > > >
      > > > > ________________________________
      > > > > From: David <davidmc36@>
      > > > > To: wuhu_software_group@yahoogroups.com
      > > > > Sent: Sun, August 15, 2010 11:13:22 AM
      > > > > Subject: [wuhu_software_group] WS2316
      > > > >
      > > > >
      > > > > Have been running the 2316 for a while now. moved to a new location and can't
      > > > > get the sensor to connect WIRED to the console. Wireless works fine. Wired
      > > > > worked before. Have replaced the wind sensor cable with CAT5 to get rid of bad
      > > >
      > > > > readings. Tried the original and CAT5 cable to hook sensor to console with no
      > > > > luck. As soon as I connect the cable it stops getting data. Does not matter if
      > > > >I
      > > > >
      > > > > hold the plus sign until it beeps or not (that's what you are supposed to do to
      > > > >
      > > > > get it to connect.)
      > > > >
      > > > > Any ideas?
      > > > >
      > > >
      > >
      >
    Your message has been successfully submitted and would be delivered to recipients shortly.