Loading ...
Sorry, an error occurred while loading the content.

Re: Inspeed Vortex

Expand Messages
  • steve_03222
    Dennis, glad it worked, you will love the Inspeed. I have had mine for a year now. Steve
    Message 1 of 11 , Mar 3, 2009
    • 0 Attachment
      Dennis, glad it worked, you will love the Inspeed. I have had mine for a year now.
      Steve


      --- In wuhu_software_group@yahoogroups.com, D Doty <oldcessna21@...> wrote:
      >
      > Thanks Steve.
      > I found the part in the forums where it said to change the alternate wind sensor to
      > type 1, but did not find the specific instructions to add the alt sensor port line to the .ini file.
      > Done now and all working fine.
      > Dennis IZAMBALES1 / CW7056
      >
      >
      >
      >
      > ________________________________
      > From: steve_03222 <steve_03222@...>
      > To: wuhu_software_group@yahoogroups.com
      > Sent: Wednesday, March 4, 2009 6:36:14 AM
      > Subject: [wuhu_software_group] Re: Inspeed Vortex
      >
      >
      > Dennis I found this in the forums
      >
      > "To enable the Inspeed, you add the following to the INI file in the
      > general setting section:
      >
      > [General Settings]
      > .
      > .
      > .
      > Alternate Wind Sensor Type=1
      > Alternate Wind Sensor Port=COM4"
      >
      > or what ever comm port your Inspeed is set up on.
      >
      > Steve
      >
      > --- In wuhu_software_ group@yahoogroup s.com, "oldcessna21" <oldcessna21@ ...> wrote:
      > >
      > > Hi Folks;
      > > This is Dennis from IZAMBALE1 in the Philippines.
      > > I just installed a Davis Pro II to replace my WMR968. (The anemometer
      > > failed)
      > > When I purchased the Davis pro, I also purchased an Inspeed Vortex
      > > anemometer.
      > > Both are now installed, and the Davis is working as advertised, but
      > > when I try to access the Vortex, the computer responds that it cannot
      > > find the alternate sensor on the port specified. I have tried to
      > > change the specified port in the .ini file and that changes the the
      > > port of the weather station.
      > > Can someone explain what I need to do to gather the info from the
      > > Vortex? The station is on com1 and the vortex is on com4.
      > > Any help will be appreciated.
      > > Dennis
      > >
      >
    • steve_03222
      I have had my Inspeed Vortex up for just over a year now. I can hear a slight squeaking noise and perhaps loosing the low end. I remember the paperwork that
      Message 2 of 11 , Mar 21, 2009
      • 0 Attachment
        I have had my Inspeed Vortex up for just over a year now. I can hear a slight squeaking noise and perhaps loosing the low end. I remember the paperwork that came with it mentioned how to lubricate the bearings. I can not seem to locate my paperwork and can not find the manual online. I think the new sapghire bearing version does not need any maintenance. Mine was the older version. Does anyone who purchased an Inspeed have a copy of the manual and can pass along how to lubricate it. I can probably just figure it out, but would hate to waste a trip to the top of the roof just to find out I couldn't figure it out...LOL.
        I am sure the company will forward me a copy, but hoped to lubricate it this weekend, thought I knew just where I put the manual....LOL
        Thanks, Steve
      Your message has been successfully submitted and would be delivered to recipients shortly.