Loading ...
Sorry, an error occurred while loading the content.

Messages List

674

Cbus 5753 PEIRL Sensor Hi Kevin, Gateway still functioning well! Quick question on the above sensor. Is it possible to read the light level via the Gateway (ie independently of

Ben Wilkinson
Jan 8
#674
 

Messages List

673

Re: Taken a few steps backwards! Success!!! The JP23 was between pins 2 and 3. I've changed it to 1 and 2,. First time around it didn't make any difference, but I took cbus power off the

Ben Wilkinson
Dec 2, 2012
#673
 

Messages List

672

Re: Taken a few steps backwards! The below is correct - they could alternatively be on 3,4 and 5 - it is the same thing. (when using a C-Bus PCI RS232 interface) In addition there should be a

Kevin Hawkins
Dec 2, 2012
#672
 

Messages List

671

Re: Fwd: Fw: [ukusa_gateway] Taken a few steps backwards! The gateway isn't able to see the C-Bus PCI interface (the data that it returns) but it is able to send data to it. I have guests here at the moment but

Kevin Hawkins
Dec 1, 2012
#671
 

Messages List

670

Re: Fwd: Fw: [ukusa_gateway] Taken a few steps backwards! I also meant to say that I’m in Bristol Ben From: ukusa_gateway@yahoogroups.com [mailto:ukusa_gateway@yahoogroups.com] On Behalf Of Ben Wilkinson Sent: 01

Ben Wilkinson
Dec 1, 2012
#670
 

Messages List

669

Re: Fwd: Fw: [ukusa_gateway] Taken a few steps backwards! Hi Kevin, I’ve been doing some testing and here are the results. See below for my responses. Thanks Ben From: ukusa_gateway@yahoogroups.com

Ben Wilkinson
Dec 1, 2012
#669
 

Messages List

668

Re: Fwd: Fw: [ukusa_gateway] Taken a few steps backwards! From what you say it's pretty difficult to determine if your gateway was ever receiving C-Bus status information. What I'm slightly concerned about is that

Kevin Hawkins
Dec 1, 2012
#668
 

Messages List

667

Fwd: Fw: [ukusa_gateway] Taken a few steps backwards! Hi Kevin,   Thanks again for your reply.   I'm out at the moment, but have answered most of your questions below.   I assume you still have the D: CB ID

Ben Wilkinson
Dec 1, 2012
#667
 

Messages List

666

Re: Taken a few steps backwards! I assume you still have the D: CB ID status and also there is still SIM ID = 0 shown ? Something has changed here because in this state there would be no

Kevin Hawkins
Dec 1, 2012
#666
 

Messages List

665

Re: Taken a few steps backwards! Hi Kevin, I've done some physical checking this morning. Wiring of the connector seems fine (checked with meter). I've gone over the instructions again

Ben Wilkinson
Dec 1, 2012
#665
 

Messages List

664

Re: Taken a few steps backwards! HI Kevin, Thanks for the quick reply. I am using the serial interface. I have a feeling this might have been happening for some time as I can't remember

Ben Wilkinson
Nov 30, 2012
#664
 

Messages List

663

Re: Taken a few steps backwards! The gateway is not able to see the C-Bus interface. I can't remember if you have the onboard C-Bus SIM or are using a C-Bus RS232 serial interface or maybe

Kevin Hawkins
Nov 30, 2012
#663
 

Messages List

662

Taken a few steps backwards! Hi Kevin, Things have gone a bit wrong today. I've been trying to use the buttons on switches to perform additional actions (to the scene setting they're

Ben Wilkinson
Nov 30, 2012
#662
 

Messages List

661

DLT re-labelling Following on from Paul's comment about using one DLT button to toggle through multiple scenes, I've gone through old messages about DLT labelling and at most,

bensbarn2001
Nov 29, 2012
#661
 

Messages List

660

Re: DLT and Saturn Scenes in the Gateway Yes - I love it, very flexible :) Paul. From: ukusa_gateway@yahoogroups.com [mailto:ukusa_gateway@yahoogroups.com] On Behalf Of Ben Wilkinson Sent: 26 November

Paul Gale
Nov 28, 2012
#660
 
View First Topic Go to View Last Topic
Loading 1 - 15 of total 674 messages