Loading ...
Sorry, an error occurred while loading the content.

Re: OTUSB problems

Expand Messages
  • e20fmc
    When I had problem connecting OTUSB via USB port. I connected it via serial port. Don t forget to give power to it.
    Message 1 of 8 , Jul 16 8:48 AM
    • 0 Attachment
      When I had problem connecting OTUSB via USB port.

      I connected it via serial port.
      Don't forget to give power to it.


      --- In tracker2@yahoogroups.com, "ve6stp" <ve6stp@...> wrote:
      >
      > Hi,
      >
      > I have an OTUSB that was working, but I'm having some problems now. I noticed that the green LED was no longer flashing indicating, what I believe is, a GPS signal.
      >
      > I hooked it up to a computer via the USB port and looked at the configuration and did not notice any problems. Under the diag screen in the configuration tool, I tried to turn on the green LED and did not notice the LED coming on. I was able to turn on and off the red LED no problem.
      >
      > Suspecting maybe a software glitch I attempted to reload the firmware to see if any difference occurred. I did not notice any difference initially.
      >
      > I unplugged the OTUSB and plugged it back in to the computer and now the computer indicates a problem with the USB device and the tracker does not come up as a port. I have tried this on 2 computers now (Win 7 and Win XP) with the same result.
      >
      > Did this OTUSB somehow brick? It seems to be stuck in a cycle of red flashes when I apply power to the OTUSB.
      >
      > Any suggestions or assistance would be appreciated.
      >
      > Thank you,
      > Stephane VE6STP
      >
    • Marcel S
      Hi Stephane, Try reloading the firmware again using OTWINCFG. Be sure to use the web update to get the newest revision. It is possible that the Green half of
      Message 2 of 8 , Jul 16 11:08 AM
      • 0 Attachment
        Hi Stephane,

        Try reloading the firmware again using OTWINCFG. Be sure to use the web
        update to get the newest revision. It is possible that the Green half of
        the LED is not working anymore (rare, but possible).

        If you computer is not recognizing the device anymore, you may need to look
        at your drivers and reinstall the .ini file that can be found on the wiki
        here: http://www.argentdata.com/files/ArgentUSB.zip

        Even with the green light not working, was the unit still working as it
        should? If yes, then it would just be an LED failure. If it was not working
        properly then you likely have something else funky going on. First steps
        for debugging would be to check all you power supplies and power rails on
        the devices. (Refer to schematics here:
        http://wiki.argentdata.com/images/Otusb-schematic.png)

        As "e20fmc" (name? call?) said in the previous email, you can also try to
        reload firmware directly through the serial port to bypass any USB
        communication issues that could be there. Just be sure to provide the
        correct power to the device.

        Cheers,

        -Marcel AI6MS

        On Tue, Jul 16, 2013 at 8:48 AM, e20fmc <e20fmc@...> wrote:

        > **
        >
        >
        > When I had problem connecting OTUSB via USB port.
        >
        > I connected it via serial port.
        > Don't forget to give power to it.
      • Scott Miller
        Have you tried connecting with the serial port instead of USB? The serial bootloader is much more likely to survive firmware corruption that the USB side.
        Message 3 of 8 , Jul 16 11:51 AM
        • 0 Attachment
          Have you tried connecting with the serial port instead of USB? The
          serial bootloader is much more likely to survive firmware corruption
          that the USB side. Also, you might try jumpering it for safe mode and
          see if that makes a difference.

          Scott

          On 7/15/2013 9:01 PM, ve6stp wrote:
          > Hi,
          >
          > I have an OTUSB that was working, but I'm having some problems now. I
          > noticed that the green LED was no longer flashing indicating, what I
          > believe is, a GPS signal.
          >
          > I hooked it up to a computer via the USB port and looked at the
          > configuration and did not notice any problems. Under the diag screen in
          > the configuration tool, I tried to turn on the green LED and did not
          > notice the LED coming on. I was able to turn on and off the red LED no
          > problem.
          >
          > Suspecting maybe a software glitch I attempted to reload the firmware to
          > see if any difference occurred. I did not notice any difference initially.
          >
          > I unplugged the OTUSB and plugged it back in to the computer and now the
          > computer indicates a problem with the USB device and the tracker does
          > not come up as a port. I have tried this on 2 computers now (Win 7 and
          > Win XP) with the same result.
          >
          > Did this OTUSB somehow brick? It seems to be stuck in a cycle of red
          > flashes when I apply power to the OTUSB.
          >
          > Any suggestions or assistance would be appreciated.
          >
          > Thank you,
          > Stephane VE6STP
          >
          >
        • ve6stp
          Hi Scott, Thank you for the reply. I tried to connect to the serial port last night, however I wasn t 100% sure what the com port settings should be. Every
          Message 4 of 8 , Jul 16 4:55 PM
          • 0 Attachment
            Hi Scott,

            Thank you for the reply.

            I tried to connect to the serial port last night, however I wasn't 100% sure what the com port settings should be.

            Every time the red LED would flash, I would see a "~" show up. My console screen looked like this:

            รพ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
            ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~



            I found the instructions on safe mode, however I can't seem to clearly see which pins would be 2 and 7. On the board where it indicates the CN4 pins, does it start from left to right 1 - 8 when the radio port is on the left and the data port is on the right ?


            Thank you,
            Stephane



            --- In tracker2@yahoogroups.com, Scott Miller <scott@...> wrote:
            >
            > Have you tried connecting with the serial port instead of USB? The
            > serial bootloader is much more likely to survive firmware corruption
            > that the USB side. Also, you might try jumpering it for safe mode and
            > see if that makes a difference.
            >
            > Scott
            >
            > On 7/15/2013 9:01 PM, ve6stp wrote:
            > > Hi,
            > >
            > > I have an OTUSB that was working, but I'm having some problems now. I
            > > noticed that the green LED was no longer flashing indicating, what I
            > > believe is, a GPS signal.
            > >
            > > I hooked it up to a computer via the USB port and looked at the
            > > configuration and did not notice any problems. Under the diag screen in
            > > the configuration tool, I tried to turn on the green LED and did not
            > > notice the LED coming on. I was able to turn on and off the red LED no
            > > problem.
            > >
            > > Suspecting maybe a software glitch I attempted to reload the firmware to
            > > see if any difference occurred. I did not notice any difference initially.
            > >
            > > I unplugged the OTUSB and plugged it back in to the computer and now the
            > > computer indicates a problem with the USB device and the tracker does
            > > not come up as a port. I have tried this on 2 computers now (Win 7 and
            > > Win XP) with the same result.
            > >
            > > Did this OTUSB somehow brick? It seems to be stuck in a cycle of red
            > > flashes when I apply power to the OTUSB.
            > >
            > > Any suggestions or assistance would be appreciated.
            > >
            > > Thank you,
            > > Stephane VE6STP
            > >
            > >
            >
          • Scott Miller
            The ~ is a good sign - it s probably running the bootloader. Try connecting with otwincfg. And yes, the pins are numbered left to right, with the pins along
            Message 5 of 8 , Jul 16 7:05 PM
            • 0 Attachment
              The ~ is a good sign - it's probably running the bootloader.  Try connecting with otwincfg.  And yes, the pins are numbered left to right, with the pins along the bottom of the board and the printing upright.

              Scott

              On 7/16/2013 4:55 PM, ve6stp wrote:
               

              Hi Scott,

              Thank you for the reply.

              I tried to connect to the serial port last night, however I wasn't 100% sure what the com port settings should be.

              Every time the red LED would flash, I would see a "~" show up. My console screen looked like this:

              þ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
              ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

              I found the instructions on safe mode, however I can't seem to clearly see which pins would be 2 and 7. On the board where it indicates the CN4 pins, does it start from left to right 1 - 8 when the radio port is on the left and the data port is on the right ?

              Thank you,
              Stephane

              --- In tracker2@yahoogroups.com, Scott Miller <scott@...> wrote:
              >
              > Have you tried connecting with the serial port instead of USB? The
              > serial bootloader is much more likely to survive firmware corruption
              > that the USB side. Also, you might try jumpering it for safe mode and
              > see if that makes a difference.
              >
              > Scott
              >
              > On 7/15/2013 9:01 PM, ve6stp wrote:
              > > Hi,
              > >
              > > I have an OTUSB that was working, but I'm having some problems now. I
              > > noticed that the green LED was no longer flashing indicating, what I
              > > believe is, a GPS signal.
              > >
              > > I hooked it up to a computer via the USB port and looked at the
              > > configuration and did not notice any problems. Under the diag screen in
              > > the configuration tool, I tried to turn on the green LED and did not
              > > notice the LED coming on. I was able to turn on and off the red LED no
              > > problem.
              > >
              > > Suspecting maybe a software glitch I attempted to reload the firmware to
              > > see if any difference occurred. I did not notice any difference initially.
              > >
              > > I unplugged the OTUSB and plugged it back in to the computer and now the
              > > computer indicates a problem with the USB device and the tracker does
              > > not come up as a port. I have tried this on 2 computers now (Win 7 and
              > > Win XP) with the same result.
              > >
              > > Did this OTUSB somehow brick? It seems to be stuck in a cycle of red
              > > flashes when I apply power to the OTUSB.
              > >
              > > Any suggestions or assistance would be appreciated.
              > >
              > > Thank you,
              > > Stephane VE6STP
              > >
              > >
              >


            • ve6stp
              Hi Scott, Thank you again for the reply. Using the otwincfg app, I was able to connect via my serial port/null modem to the devices data port and Erase
              Message 6 of 8 , Jul 16 9:58 PM
              • 0 Attachment
                Hi Scott,

                Thank you again for the reply. Using the otwincfg app, I was able to connect via my serial port/null modem to the devices data port and "Erase device and load firmware" to restore the device to what appears to be a functional state.

                Upon firmware load and initial configuration through the otwincfg app, I was able to verify that the both the red and green LED works through the "Tuning/Diagnostics" section.

                After I wrote the config to the tracker and quit the program, the tracker seemed to be working as it was beaconing as expected.

                I noticed the green LED was not flashing however. Is it not supposed to flash to indicate it has GPS lock? I went back to the otwincfg / Tuning/Diagnostics section and was no longer able to get the green LED to light up.

                Have you run into this before? The firmware on the tracker is 56412.

                Thank you,
                Stephane



                --- In tracker2@yahoogroups.com, Scott Miller <scott@...> wrote:
                >
                > The ~ is a good sign - it's probably running the bootloader. Try
                > connecting with otwincfg. And yes, the pins are numbered left to right,
                > with the pins along the bottom of the board and the printing upright.
                >
                > Scott
              • Scott Miller
                If you can t get the green LED to light from the tuning/diagnostics screen, it could be a bad solder joint. The OTUSB uses an 0805 size bicolor LED and
                Message 7 of 8 , Jul 17 10:19 AM
                • 0 Attachment
                  If you can't get the green LED to light from the tuning/diagnostics
                  screen, it could be a bad solder joint. The OTUSB uses an 0805 size
                  bicolor LED and they're probably the most problematic part on the board
                  when it comes to proper solder flow. If you're OK with taking a
                  soldering iron to it, you can touch up the four connections at the
                  corners of the LED. A bit of flux will help a lot. And of course
                  you're always welcome to send it back here for repair.

                  Scott

                  On 7/16/2013 9:58 PM, ve6stp wrote:
                  >
                  > Hi Scott,
                  >
                  > Thank you again for the reply. Using the otwincfg app, I was able to
                  > connect via my serial port/null modem to the devices data port and
                  > "Erase device and load firmware" to restore the device to what appears
                  > to be a functional state.
                  >
                  > Upon firmware load and initial configuration through the otwincfg app, I
                  > was able to verify that the both the red and green LED works through the
                  > "Tuning/Diagnostics" section.
                  >
                  > After I wrote the config to the tracker and quit the program, the
                  > tracker seemed to be working as it was beaconing as expected.
                  >
                  > I noticed the green LED was not flashing however. Is it not supposed to
                  > flash to indicate it has GPS lock? I went back to the otwincfg /
                  > Tuning/Diagnostics section and was no longer able to get the green LED
                  > to light up.
                  >
                  > Have you run into this before? The firmware on the tracker is 56412.
                  >
                  > Thank you,
                  > Stephane
                  >
                  > --- In tracker2@yahoogroups.com <mailto:tracker2%40yahoogroups.com>,
                  > Scott Miller <scott@...> wrote:
                  > >
                  > > The ~ is a good sign - it's probably running the bootloader. Try
                  > > connecting with otwincfg. And yes, the pins are numbered left to right,
                  > > with the pins along the bottom of the board and the printing upright.
                  > >
                  > > Scott
                  >
                  >
                Your message has been successfully submitted and would be delivered to recipients shortly.