Loading ...
Sorry, an error occurred while loading the content.

1496Re: [sawsmith] Newbie new owner of Sawsmith - where do I start?

Expand Messages
  • grandpadon47@sbcglobal.net
    Apr 2, 2012
      Opps Sorry Jeff I meant to say look in messages and type in a search word. grandpadon in Missouri

      --- On Mon, 4/2/12, Matthew Tritt <windgooroo1@...> wrote:

      From: Matthew Tritt <windgooroo1@...>
      Subject: Re: [sawsmith] Newbie new owner of Sawsmith - where do I start?
      To: sawsmith@yahoogroups.com
      Date: Monday, April 2, 2012, 3:43 PM

      Reolace the coiled motor power cord! As I learned the hard way, they become brittle with time and can (and will) break, which can cause a short from + to -, which will destroy either the relay (none available), the capacitor (difficult to find) or the motor - perhaps all three. A new motor can be built for around $1,200. In other words, spend $15.00 and be safe.
      The mitre angle release is probably mucked up from not being used for so long as will be a number of controls. Disassemble, clean and lubricate all the parts that don't wnat to work. This takes time, patience and an understanding of how they are put together. A lot of aluminum was used in these machines, and we all know what happens to aluminum when exposed to a humid environment without adequate protection.
      The bevel gears will only be a problem if they have been forced beyond the strength of the metal they were made from. Forcing them could be from a failure to keep them lubed, or even from dropping the whole thing on the crank handle. I might have a set of these gears available if worse comes to worse.

      From: jeffwhataguy <jeffwhataguy@...>
      To: sawsmith@yahoogroups.com
      Sent: Sun, April 1, 2012 2:34:18 PM
      Subject: [sawsmith] Newbie new owner of Sawsmith - where do I start?

      My neighbor gave me a sawsmith that has been in his barn for a LONG time. It is in visually good condition. I have all the manuals (the ones that are already online). I tested that it spins when powered up, so the switch and motor and cables are good.

      But this is my first experience with a Sawsmith, or any RAS for that matter. I've got lots of experience with a basic old Sears tablesaw but the adjustments on that are comparatively trivial. Sorry to ask so many questions in my first post; I'de welcome links to where these questions have already been answered if they have.

      1. What should I do to the saw before I start trying to use it? Any lubrication or anything else that needs checking so I don't damage it when I start using it?

      2. I'm having trouble making sense of the directions. I can't figure out how to do some fundamental things like adjust the miter angle? Arm lock and Yoke lock don't seem to release it - still locked into place. This is hopefully a basic question - step by step how do I adjust the miter angle?

      3. Similar problem with the "twist lock handle". It doesn't twist for me - plus there is a chrome knob on top of the handle that isn't shown in the manual and that I don't know what to do with. Any hints on how this works so I can bevel the blade?

      4. Beyond not knowing how to adjust it, my main known problem at this point is that the bevel gear is missing a tooth. When I got it the crank arm and gear weren't even installed. They were in a box with a few other parts including another bevel gear that is in even worse shape, so it looks like this is a weak link. I found a link for a replacement part on the Database page, though the link didn't work. Is there still a source for this part? The arm seems like it is very heavy and will strip out a new gear if I'm able to find one. Any advice on how to lubricate this so I can lift it manually to make the saw usable until I can get a new gear?

      5. Only other known problem at this point are the table (particle board) is lifting on the sides so I guess I'll have to make a new one out of plywood. At this point I assume I can use 3/4" plywood - is there a better way to go?

      Thanks for listening,
      Jeff, Serial Number 714083.

    • Show all 11 messages in this topic