Fwd: Re: How to build crosstool-0.28-rc32 for NSLU2 Linux development
- Thanks, i just tried crosstool-0.28-rc35, same problem. maybe it is
just my setup
Did you use the gcc-3.3.2-arm-softfloat.patch that is mentioned in the
HowToCompile? I will go try that too.
--- In firstname.lastname@example.org, "mark5segal" <liuyafei@g...> wrote:
Did you try "crosstool-0.28-rc35"? I got it built on FC3 and Gentoo.
--- In email@example.com, "Jwahar Bammi" <bammi@m...> wrote:
> Has anyone succeed with this procedure on Fedora FC3?
> I followed this procedure twice (to make sure), and the build fails
> when it is building glibc, with the following message
> armv5b-softfloat-linux/bin/ld: cannot represent machine `arm:linux'
> (this error occurs in the step where it is building crt1.o)
> (this same happens when i follow the Howto to build oe based
> unslung-image -- it tries to build the cross tools, and fails with the
> same message at the same point. This leads me to suspect something in
> the Fedora FC3 setup is throwing bot these procedures off. (I have
> checked and doubled checked all the setting, unset LD_LIBRARY_PATH,
> C_INCLUDE_PATH etc))
> any comments much appreciated.
> --- In firstname.lastname@example.org, NSLU2 Linux <unslung@g...> wrote:
> > 1/ Grab a Linux box (I used Debian 3.1 "testing" on an Intel
> > Other architectures and versions of Linux may well work. If you get
> > errors, then start again on an i386 Debian 3.1 box. In particular the
> > version of gcc that I used was: gcc (GCC) 3.3.4 (Debian 1:3.3.4-3).
> > Don't ask about how to do it on a Mac OS-X box, because I can't help
> > you. Hopefully someone else will work that out and post a how-to like
> > this one.
> > 2/ Download crosstool-0.28-rc32 from:
> > http://kegel.com/crosstool/crosstool-0.28-rc32.tar.gz
> > You need to use crosstool version 0.28-rc32 (not rc34, and not rc35,
> > and not any other version either). You're on your own if you decide
> > to ignore this advice. Other versions probably will work (with some
> > patching), but no-one has posted a how-to for a different version, so
> > why waste your time? Of course, if you are the person who is
> > knowledgeable enough to get a newer version to work without bugging
> > any other people who are happily using 0.28-rc32, then please do so
> > and post your how-to here so that we can *all* upgrade to the new
> > version *together*.
> > 3/ Untar that - it will create a crosstool-0.28-rc32 directory.
> > 4/ Detach the demo-nslu2.sh file from this message and put it in
> that directory.
> > This file assumes that you have write access to /opt/crosstool (this
> > is where your resulting toolchain will end up) and $HOME/downloads
> > (this is where all the downloads will be stored). If you don't, then
> > change the paths to suit. Do *not* change any of the tool version
> > numbers in this file. Don't even be tempted ...
> > 5/ Download the required patch from:
> > 6/ Put the patch in the patches/gcc-3.3.3 directory (yes, I know the
> > patch says 3.3.2 - put it in the 3.3.3 directory anyway). Don't try
> > and apply it manually or anything like that - just put it there and
> > leave it alone.
> > 7/ Change directory into the crosstool-0.28-rc32 directory.
> > 8/ Type "sh demo-nslu2.sh" and wait for a long time (yes it could be
> > 9/ Add the
> > directory to your PATH. Verify that you can run
> > "armv5b-softfloat-linux-gcc --version".
> > This process was worked out by Benoit on Aug 17
> > (http://groups.yahoo.com/group/nslu2-linux/message/422), and has been
> > followed successfully by at least 10 different people since then. So
> > if you have problems, it's not because of crosstool or the patch (and
> > no, you shouldn't try a different version if you can't get this
> > version to work). Look to your own actions first.
> > If you have problems (and have followed this exact procedure twice
> > with the same result), then post your complete Linux O/S details, the
> > URLs and md5sums of all the files you downloaded (including the
> > demo-nslu2.sh file you detached from this message), the *exact*
> > commands you typed (yes, every single one of them, cut and pasted from
> > your shell window), and the error messages (again, cut and pasted from
> > your shell window).
> > Have fun!
> > [Did I mention that you have to use crosstool version 0.28-rc32? I
> did? Good.]
> > #!/bin/sh
> > set -ex
> > TARBALLS_DIR=$HOME/downloads
> > RESULT_TOP=/opt/crosstool
> > export TARBALLS_DIR RESULT_TOP
> > GCC_LANGUAGES="c,c++"
> > export GCC_LANGUAGES
> > # Really, you should do the mkdir before running this,
> > # and chown /opt/crosstool to yourself so you don't need to run as
> > mkdir -p $RESULT_TOP
> > # Build the toolchain. Takes a couple hours and a couple gigabytes.
> > eval `cat armv5b-softfloat.dat gcc-3.3.3-glibc-2.2.5.dat` sh all.sh
> > echo Done.
--- End forwarded message ---