Loading ...
Sorry, an error occurred while loading the content.

Looking for replacement AC adaptor

Expand Messages
  • dystopianrebel
    The AC adaptor for one of my Slugs has failed. By swapping adaptors, I know that the Slug itself is still good. If you have a spare that you will not be using
    Message 1 of 6 , Mar 28, 2012
    • 0 Attachment
      The AC adaptor for one of my Slugs has failed. By swapping adaptors, I know that the Slug itself is still good.

      If you have a spare that you will not be using or want to sell, please contact me.
    • Ed Watson
      I had the same problem. I found that a USB hub can power it fine. So I bought a cheap one of those. I think I made sure it was over 1.0A. What I did in the end
      Message 2 of 6 , Mar 28, 2012
      • 0 Attachment
        I had the same problem.

        I found that a USB hub can power it fine. So I bought a cheap one of those.
        I think I made sure it was over 1.0A.

        What I did in the end was used the same adapter 3.0A  USB hub power supply to power the USB hub connected and the slug 
        (Wired up in parallel) works great.

        Hope this helps. 

        Ed



        On 28 March 2012 13:09, dystopianrebel <dystopianrebel@...> wrote:
         

        The AC adaptor for one of my Slugs has failed. By swapping adaptors, I know that the Slug itself is still good.

        If you have a spare that you will not be using or want to sell, please contact me.


      • mstombs
        I had this problem and managed to repair the PSU, required surgical dissection and replacement of 2 100uF electrolytic capacitors - just hope the glued/taped
        Message 3 of 6 , Mar 28, 2012
        • 0 Attachment
          I had this problem and managed to repair the PSU, required surgical dissection and replacement of 2 100uF electrolytic capacitors - just hope the glued/taped case doesn't start a fir and burn the house down... You can buy new replacements cheaply on fleabay I'm sure...

          --- In nslu2-linux@yahoogroups.com, Ed Watson <edmundwatson@...> wrote:
          >
          > I had the same problem.
          >
          > I found that a USB hub can power it fine. So I bought a cheap one of those.
          > I think I made sure it was over 1.0A.
          >
          > What I did in the end was used the same adapter 3.0A USB hub power supply
          > to power the USB hub connected and the slug
          > (Wired up in parallel) works great.
          >
          > Hope this helps.
          >
          > Ed
          >
          >
          >
          > On 28 March 2012 13:09, dystopianrebel <dystopianrebel@...> wrote:
          >
          > > **
          > >
          > >
          > > The AC adaptor for one of my Slugs has failed. By swapping adaptors, I
          > > know that the Slug itself is still good.
          > >
          > > If you have a spare that you will not be using or want to sell, please
          > > contact me.
          > >
          > >
          > >
          >
        • Ralph Finch
          Or...get a brand x power supply with the same output voltage and max current. If the plug is not the same, no problem, cut the wires of the replacement and
          Message 4 of 6 , Mar 28, 2012
          • 0 Attachment
            Or...get a brand x power supply with the same output voltage and max current. If the plug is not the same, no problem, cut the wires of the replacement and defunct PSU, and wire the old plug to the new PSU. Solder, crimps, whatever, separate with heat shrink tubing (best) or electrical tape, etc.

            On Wed, Mar 28, 2012 at 5:09 AM, dystopianrebel <dystopianrebel@...> wrote:
             

            The AC adaptor for one of my Slugs has failed. By swapping adaptors, I know that the Slug itself is still good.

            If you have a spare that you will not be using or want to sell, please contact me.


          • Jimmy C. Chau
            Just to clarify, you don t need to match the max current; the max current of the power supply just needs to be at least as large (as the max current of the
            Message 5 of 6 , Apr 14, 2012
            • 0 Attachment
              Just to clarify, you don't need to match the max current; the max
              current of the power supply just needs to be at least as large (as the
              max current of the NSLU2 or the original power supply).

              When replacing power supplies, check that:
              - the plug matches,
              - the polarity matches (whether the center is + or -, this is usually
              indicated in symbol form),
              - the output voltage is identical,
              - the output current rating of the power supply is larger than the
              current rating of the load (in this case, the NSLU2),
              - and that the power supply is compatible with your wall power (if
              you're buying the power supply domestically, this last point is
              probably true).

              Best regards,
              -Jimmy

              On Wed, 28 Mar 2012 12:20:28 -0700
              Ralph Finch <ralphmariafinch@...> wrote:

              > Or...get a brand x power supply with the same output voltage and max
              > current. If the plug is not the same, no problem, cut the wires of the
              > replacement and defunct PSU, and wire the old plug to the new PSU.
              > Solder, crimps, whatever, separate with heat shrink tubing (best) or
              > electrical tape, etc.
              >
              > On Wed, Mar 28, 2012 at 5:09 AM, dystopianrebel
              > <dystopianrebel@...>wrote:
              >
              > > **
              > >
              > >
              > > The AC adaptor for one of my Slugs has failed. By swapping
              > > adaptors, I know that the Slug itself is still good.
              > >
              > > If you have a spare that you will not be using or want to sell,
              > > please contact me.
              > >
            • Ettore
              Mind that some power supplies have a max current and a minimal current. If the max current is significantly larger that the one of the official power supply
              Message 6 of 6 , Apr 15, 2012
              • 0 Attachment
                Mind that some power supplies have a max current and a minimal current.

                If the max current is significantly larger that the one of the official power supply (which now I don't recall) you have more chances that the NSLU2 without or even with load (HD)
                won't draw enough power to keep the replacement power supply active.

                It happened to me: I had to disable the low-power mode of my USB HD (as I was too lazy to solder a resistor on the supply cable).

                Ettore

                If the nominal max current is much larger than the one actually

                2012/4/15 Jimmy C. Chau <chaujc@...>
                 

                Just to clarify, you don't need to match the max current; the max
                current of the power supply just needs to be at least as large (as the
                max current of the NSLU2 or the original power supply).

                When replacing power supplies, check that:
                - the plug matches,
                - the polarity matches (whether the center is + or -, this is usually
                indicated in symbol form),
                - the output voltage is identical,
                - the output current rating of the power supply is larger than the
                current rating of the load (in this case, the NSLU2),
                - and that the power supply is compatible with your wall power (if
                you're buying the power supply domestically, this last point is
                probably true).

                Best regards,
                -Jimmy



                On Wed, 28 Mar 2012 12:20:28 -0700
                Ralph Finch <ralphmariafinch@...> wrote:

                > Or...get a brand x power supply with the same output voltage and max
                > current. If the plug is not the same, no problem, cut the wires of the
                > replacement and defunct PSU, and wire the old plug to the new PSU.
                > Solder, crimps, whatever, separate with heat shrink tubing (best) or
                > electrical tape, etc.
                >
                > On Wed, Mar 28, 2012 at 5:09 AM, dystopianrebel
                > <dystopianrebel@...>wrote:
                >
                > > **

                > >
                > >
                > > The AC adaptor for one of my Slugs has failed. By swapping
                > > adaptors, I know that the Slug itself is still good.
                > >
                > > If you have a spare that you will not be using or want to sell,
                > > please contact me.
                > >


              Your message has been successfully submitted and would be delivered to recipients shortly.