Loading ...
Sorry, an error occurred while loading the content.

Re: [nslu2-linux] Hello and a small question concerning Unslung

Expand Messages
  • Rob Lockhart
    Hi, Pierre. My apologies, I don t use unslug, I ve only used debian slug mostly. For these kinds of questions, you might have more luck on the nslu2-general
    Message 1 of 16 , May 4, 2008
    • 0 Attachment
      Hi, Pierre.  My apologies, I don't use unslug, I've only used debian slug mostly.  For these kinds of questions, you might have more luck on the nslu2-general group, or perhaps searching the archives?  I looked on the wiki http://www.nslu2-linux.org/wiki/Unslung/HomePage but I couldn't find anything relevant to dhcp.  Once I saw the effort required to get unslung working (for me), I went the debian approach.  But it does have its drawbacks, especially if the hard drive dies and you have to reinstall the OS (but not userspace).

      Good luck,
        -Rob

      On Sun, May 4, 2008 at 3:05 PM, Pierre-François (f5bqp_pfm) <pfmonet@...> wrote:
      Hi Rob,
       
      I got the 10 oz of vodka and the rest... lol...
      My concern now is I cannot get out from the DHCP as far I see my fixed address when I type "uci show network.lan" .
      What should I modify into the /etc/config/dhcp ? Delete the line "option ignore 1" into config dhcp ? or put a 0 instead of 1 ?
      It's unclear, I thought that 1 was setting up the "ignore dhcp"!
       


    • Pierre-François (f5bqp_pfm)
      Hi Rob, No no, when I said I got the 10oz of vodka and the rest... it s because I booted Openwrt! At the serial console port there is a funny pleasant
      Message 2 of 16 , May 4, 2008
      • 0 Attachment
        Hi Rob,
         
        No no, when I said "I got the 10oz of vodka and the rest..." it's because I booted Openwrt! At the serial console port there is a funny pleasant message :"10 oz of vodka, 10 oz Triple sec 10 oz of lime juice ...", so my small joke was to show you I finally booted OpenWrt...
        And I'd a STATIC IP configuring because I think there is something strange into the configuration after the flashing, but finally I just found how to turnaround the problem by configuring by hand the config DHCP file to disable it. And after I discovered that ther is a nice GUI interface also permitting to configure everything even more easily!
         
        Now I need to add my memory and I don't know how to do. I see Redboot at the boot but I don't see APEX. Should I see it or not?
         
        I assume you're running OpenWrt, am I right?
         
        And good night if it's time for you also... Here I'll continue to play with the slug...
        pf
         
         
         
        ----- Original Message -----
        Sent: Sunday, May 04, 2008 10:58 PM
        Subject: Re: [nslu2-linux] Hello and a small question concerning Unslung

        Hi, Pierre.  My apologies, I don't use unslug, I've only used debian slug mostly.  For these kinds of questions, you might have more luck on the nslu2-general group, or perhaps searching the archives?  I looked on the wiki http://www.nslu2- linux.org/ wiki/Unslung/ HomePage but I couldn't find anything relevant to dhcp.  Once I saw the effort required to get unslung working (for me), I went the debian approach.  But it does have its drawbacks, especially if the hard drive dies and you have to reinstall the OS (but not userspace).

        Good luck,
          -Rob

        On Sun, May 4, 2008 at 3:05 PM, Pierre-François (f5bqp_pfm) <pfmonet@wanadoo. fr> wrote:
        Hi Rob,
         
        I got the 10 oz of vodka and the rest... lol...
        My concern now is I cannot get out from the DHCP as far I see my fixed address when I type "uci show network.lan" .
        What should I modify into the /etc/config/ dhcp ? Delete the line "option ignore 1" into config dhcp ? or put a 0 instead of 1 ?
        It's unclear, I thought that 1 was setting up the "ignore dhcp"!
         




        __________ Information NOD32 3072 (20080503) __________

        Ce message a ete verifie par NOD32 Antivirus System.
        http://www.nod32.com
      • Rod Whitby
        If you built openwrt yourself, it will have apex. I don t remember whether the latest binary release uses it or not. Once you have apex, you can change it s
        Message 3 of 16 , May 4, 2008
        • 0 Attachment
          If you built openwrt yourself, it will have apex. I don't remember whether the latest binary release uses it or not.
          Once you have apex, you can change it's startup command (using the apex-env package or your seriall console) to memscan for 64MB max.
          -- Rod

          -----Original Message-----
          From: =?iso-8859-1?Q?Pierre-Fran=E7ois_=28f5bqp=5Fpfm=29?= <pfmonet@...>
          Date: Monday, May 5, 2008 7:39 am
          Subject: Re: [nslu2-linux] Hello and a small question concerning Unslung
          To: <nslu2-linux@yahoogroups.com>Reply-To: nslu2-linux@yahoogroups.com


          >Hi Rob,
          >
          >No no, when I said "I got the 10oz of vodka and the rest..." it's because I booted Openwrt! At the serial console port there is a funny pleasant message :"10 oz of vodka, 10 oz Triple sec 10 oz of lime juice ...", so my small joke was to show you I finally booted OpenWrt...
          >And I'd a STATIC IP configuring because I think there is something strange into the configuration after the flashing, but finally I just found how to turnaround the problem by configuring by hand the config DHCP file to disable it. And after I discovered that ther is a nice GUI interface also permitting to configure everything even more easily!
          >
          >Now I need to add my memory and I don't know how to do. I see Redboot at the boot but I don't see APEX. Should I see it or not?
          >
          >I assume you're running OpenWrt, am I right?
          >
          >And good night if it's time for you also... Here I'll continue to play with the slug...
          >pf
          >
          >
          > ----- Original Message ----- From: Rob Lockhart To: nslu2-linux@yahoogroups.com Sent: Sunday, May 04, 2008 10:58 PM Subject: Re: [nslu2-linux] Hello and a small question concerning Unslung
          >
          >
          >
          >Hi, Pierre. My apologies, I don't use unslug, I've only used debian slug mostly. For these kinds of questions, you might have more luck on the nslu2-general group, or perhaps searching the archives? I looked on the wiki http://www.nslu2-linux.org/wiki/Unslung/HomePage but I couldn't find anything relevant to dhcp. Once I saw the effort required to get unslung working (for me), I went the debian approach. But it does have its drawbacks, especially if the hard drive dies and you have to reinstall the OS (but not userspace).
          >
          >Good luck,
          > -Rob
          >
          > On Sun, May 4, 2008 at 3:05 PM, Pierre-Fran�ois (f5bqp_pfm) pfmonet@...> wrote:
          >
          >Hi Rob,
          >
          >I got the 10 oz of vodka and the rest... lol...
          >My concern now is I cannot get out from the DHCP as far I see my fixed address when I type "uci show network.lan" .
          >What should I modify into the /etc/config/dhcp ? Delete the line "option ignore 1" into config dhcp ? or put a 0 instead of 1 ?
          >It's unclear, I thought that 1 was setting up the "ignore dhcp"!
          >
          >
          >
          >
          >
          >
          >__________ Information NOD32 3072 (20080503) __________
          >
          >Ce message a ete verifie par NOD32 Antivirus System.
          >http://www.nod32.com
          >
        • Pierre-François (f5bqp_pfm)
          Hi Rod, I installed Openwrt, openwrt-kamikaze-nslu2.bin (Kernel Linux 2.6.21.6) and when I boot with a ctrlC after the + I go into Redboot, I don t see APEX
          Message 4 of 16 , May 4, 2008
          • 0 Attachment
            Hi Rod,

            I installed Openwrt, openwrt-kamikaze-nslu2.bin (Kernel Linux 2.6.21.6)
            and when I boot with a ctrlC after the + I go into Redboot, I don't see APEX
            as you said it's included.
            Probably I miss something?

            pf

            ----- Original Message -----
            From: "Rod Whitby" <rod@...>
            To: <nslu2-linux@yahoogroups.com>
            Sent: Sunday, May 04, 2008 9:51 AM
            Subject: Re: [nslu2-linux] Hello and a small question concerning Unslung


            The standard nslu2 image built by openwrt includes apex as the second stage
            bootloader. Just flash it with upslug2, find out which dhcp address it
            acquired and then telnet in. I assume that since you've done a memory
            upgrade then you also have a serial console.
            Note that there are unresolved kernel issues in running slugs with more than
            64MB, so you may want to tell apex to restrict the memory size passed to the
            kernel to 64MB, unless you want to be part of the debugging effort for this
            problem which hasn't been cracked in almost 2 years or more ...
            -- Rod

            -----Original Message-----
            From: =?iso-8859-1?Q?Pierre-Fran=E7ois_=28f5bqp=5Fpfm=29?=
            <pfmonet@...>
            Date: Sunday, May 4, 2008 5:42 pm
            Subject: Re: [nslu2-linux] Hello and a small question concerning Unslung
            To: <nslu2-linux@yahoogroups.com>Reply-To: nslu2-linux@yahoogroups.com

            Hi,
            >
            >Finally I could make my Slug running properly with Unslug and the packages
            >Xinetd + Samba2 + Fuppes as I was expecting (Xinetd to have permanently
            >TELNET loaded, it's more simple to use than Tssh on a pure private
            >network).
            >
            >Now next step I want to take advantage of the mem upgrade I already made up
            >to 256MB (4 x 512mbit chips) and then running the same packages plus some
            >others.
            >I anticipate to run OpenWrt to try to run with no hard disks in a later
            >stage (except the NAS where are stored the video files). (probably I'll
            >have
            >to upgrade to ObeseSlug if 8MB flash isn't sufficient).
            >
            >Where can I find an url on how to load APEX on top of Redboot before I
            >switch to OpenWrt, I don't want to mix the problems... One at a time...
            >I've tried to find something, I found many sites talking APEX but not one
            >really good ( or unclear for me...) on how to keep Redboot below APEX. Can
            >you help?
            >
            >For info I wasn't able to mount under Unslung the NAS file system with the
            >command "mount -t smbfs .... ", it doesn't work with Unslung as it should,
            >I
            >don't know why but nevermind I found a solution: I was forced to use the
            >direct command "/usr/bin/smbmount //ip_nas/nas_filesystem_to_mount
            >/mnt/...").
            >This was the cause of my problem explained earlier.
            >
            >
            >Many thanks.
            >pf
            >
            >
            >
            >
            >
            >----- Original Message -----
            >From: "Rod Whitby" <rod@...>
            >To: <nslu2-linux@yahoogroups.com>
            >Sent: Sunday, April 20, 2008 12:17 AM
            >Subject: Re: [nslu2-linux] Hello and a small question concerning Unslung
            >
            >
            >Put 'cat ' in front of each of your two commands.
            >Note that you won't be able to use the 256MB with Unslung without
            >recompiling a modified kernel source. Latest SlugOS and OpenWrt will
            >definitely use it, and I think latest Debian will too.
            >Also note there are still unresolved issues with mem > 64MB (search the
            >mailing list archive at gmane.org for details).
            >-- Rod
            >
            >-----Original Message-----
            >From: "f5bqp_pfm" <pfmonet@...>
            >Date: Sunday, Apr 20, 2008 1:21 am
            >Subject: [nslu2-linux] Hello and a small question concerning Unslung
            >To: nslu2-linux@yahoogroups.comReply-To: nslu2-linux@yahoogroups.com
            >
            >
            >>Hello to everyone,
            >
            >>As a new member and a new NSLU2 user I firstly want say hello to all
            >of you, members of this fancy toy group... I hope you'll not have to
            >suffer to much of some of my stupid questions... lol...
            >
            >>I've started to upgrade my slug up to 256MB to be able to work with
            >enough space and I thank my binocular who helped greatly...
            >Now I've intalled Unslung-6.10 to start to play with, as a first step.
            >Then probably I'll switch to Debian, which probably is more a real
            >Linux, but before I wanted to be sure to manage properly the slug and
            >its capabilities.
            >One thing at a time... but as from time to time I'm a Linux user I
            >believe that Unslung will borrow me rather soon...
            >Now the question:
            >The first two commands I tried to type are /proc/meminfo and
            >/proc/cpuinfo and I got a frustrating injure! Permission Denied! And I
            >was logged as root. Then I've tried su to retype the commands same
            >injure!
            >Does this means that under Unslung-6.10 there is no way to be logged
            >as Super User to be able to execute admin commands?
            >
            >>Thanks in advance for your help.
            >
            >>pf
            >(Pierre-François)
            >
            >>
            >
            >>
            >
            >>------------------------------------
            >
            >>Yahoo! Groups Links
            >
            >>
            >
            >>
            >
            >
            >------------------------------------
            >
            >Yahoo! Groups Links
            >
            >
            >
            >
            >
            >__________ Information NOD32 3040 (20080419) __________
            >
            >Ce message a ete verifie par NOD32 Antivirus System.
            >http://www.nod32.com
            >
            >
            >
            >
            >------------------------------------
            >
            >Yahoo! Groups Links
            >
            >
            >
            >


            ------------------------------------

            Yahoo! Groups Links





            __________ Information NOD32 3072 (20080503) __________

            Ce message a ete verifie par NOD32 Antivirus System.
            http://www.nod32.com
          • jean jacques goesens
            Hi Pierre François, Happy to read you! If you look at the boot log, you must see something like this : *RedBoot(tm) bootstrap and debug environment [ROMRAM]
            Message 5 of 16 , May 4, 2008
            • 0 Attachment
              Hi Pierre François,

              Happy to read you!

              If you look at the boot log, you must see something like this :

              *RedBoot(tm) bootstrap and debug environment [ROMRAM]
              Red Hat certified release, version 1.92 - built 15:16:07, Feb 3 2004

              Platform: IXDP425 Development Platform (XScale)
              Copyright (C) 2000, 2001, 2002, Red Hat, Inc.

              RAM: 0x00000000-0x02000000, 0x000723a0-0x01ff3000 available
              FLASH: 0x50000000 - 0x50800000, 64 blocks of 0x00020000 bytes each.
              == Executing boot script in 2.000 seconds - enter ^C to abort
              RedBoot> boot;exec 0x01d00000
              have eRcOmM
              copy kernel code from flash to RAM
              copy ramdisk file from flash to RAM
              run kernel
              Using base address 0x01d00000 and length 0x0000bc00
              Ans

              APEX Boot Loader 1.5.11 -- Copyright (c) 2004,2005,2006,2007 Marc Singer
              compiled for Debian NSLU2

              APEX comes with ABSOLUTELY NO WARRANTY. It is free software and
              you are welcome to redistribute it under certain circumstances.
              For details, refer to the file COPYING in the program source.

              apex => mem:0x00200000+0xbc00 (48128 bytes)
              env => nor:0x7c000+15k (no-write)

              Use the command 'help help' to get started.

              # sdram-init
              1 bank of 2 512Mib chips
              # memscan -u 0+256m
              0x0 0x08000000 (128 MiB)
              # copy -s $kernelsrc $bootaddr
              # copy -s fis://kernel 0x00008000
              1441760 bytes transferred
              # copy -s $ramdisksrc $ramdiskaddr
              # copy -s fis://ramdisk 0x01000000
              6291440 bytes transferred
              # wait 10 Type ^C key to cancel autoboot.
              Type ^C key to cancel autoboot.
              # boot
              ATAG_HEADER
              ATAG_MEM: start 0x00000000 size 0x08000000
              ATAG_CMDLINE: (55 bytes) 'console=ttyS0,115200 rtc-x1205.probe=0,0x6f noirqdebu'
              ATAG_INITRD2: start 0x01000000 size 0x00400000
              ATAG_END
              Booting kernel at 0x00008000... *

              if you type CTRL-C at boot you interrupt Redboot, so you cannot see the
              next steps..

              you must wait for getting into Apex to type CTRL-C and interrupt APEX.

              the try to type memscan -u 0+512m, it should answer :

              ** 0x0 0x08000000 (128 MiB)
              **or**
              **** 0x0 0x10000000 (256 MiB) **
              or**
              **** 0x0 0x20000000 (512 MiB) **


              The memory may be limited by two things:

              1) It depends if APEX was compiled with 2 banks support or not, if compiled for only one bank,
              the second (piggy pack) will be ignored.
              2) It depends also of the memscan command in the environment, it limits the memory
              scan so extra memory is not detected.

              If it works, you can type the rest of the sequence manually to boot linux
              and check if you get the whole intended memory.
              Here is the link wich was the most useful for me:
              http://www.nslu2-linux.org/wiki/Debian/CompileApex
              It is (relatively) simple to compile apex on the target machine and to copy it
              directly into mtd2.
              When it works, you can create a comple flash image with your version(s)
              to keep it ready for recover a machine in case of trouble or to flash another machine.

              I wrote a small batch in order to create the image.bin file, i need to find it on my slug:


              *#! /bin/sh
              echo recuperation des blocks

              dd if=/dev/mtdblock0 of=block0.bin
              dd if=/dev/mtdblock1 of=block1.bin
              dd if=/dev/mtdblock2 of=block2.bin
              dd if=/dev/mtdblock3 of=block3.bin
              dd if=/dev/mtdblock4 of=block4.bin
              dd if=/dev/mtdblock5 of=block5.bin

              echo creation de l image

              cat block0.bin block1.bin block2.bin block3.bin block4.bin block5.bin > image.bin

              *image.bin contains the current flash image, keep it preciousely!

              Personally, i created as this two images, one with the 64M memory,
              another with 256M-2 banks limitation.

              JJ



              Pierre-François (f5bqp_pfm) a écrit :
              >
              > Hi Rod,
              >
              > I installed Openwrt, openwrt-kamikaze-nslu2.bin (Kernel Linux 2.6.21.6)
              > and when I boot with a ctrlC after the + I go into Redboot, I don't
              > see APEX
              > as you said it's included.
              > Probably I miss something?
              >
              > pf
              >
              > ----- Original Message -----
              > From: "Rod Whitby" <rod@... <mailto:rod%40whitby.id.au>>
              > To: <nslu2-linux@yahoogroups.com <mailto:nslu2-linux%40yahoogroups.com>>
              > Sent: Sunday, May 04, 2008 9:51 AM
              > Subject: Re: [nslu2-linux] Hello and a small question concerning Unslung
              >
              > The standard nslu2 image built by openwrt includes apex as the second
              > stage
              > bootloader. Just flash it with upslug2, find out which dhcp address it
              > acquired and then telnet in. I assume that since you've done a memory
              > upgrade then you also have a serial console.
              > Note that there are unresolved kernel issues in running slugs with
              > more than
              > 64MB, so you may want to tell apex to restrict the memory size passed
              > to the
              > kernel to 64MB, unless you want to be part of the debugging effort for
              > this
              > problem which hasn't been cracked in almost 2 years or more ...
              > -- Rod
              >
              > -----Original Message-----
              > From: =?iso-8859-1?Q?Pierre-Fran=E7ois_=28f5bqp=5Fpfm=29?=
              > <pfmonet@... <mailto:pfmonet%40wanadoo.fr>>
              > Date: Sunday, May 4, 2008 5:42 pm
              > Subject: Re: [nslu2-linux] Hello and a small question concerning Unslung
              > To: <nslu2-linux@yahoogroups.com
              > <mailto:nslu2-linux%40yahoogroups.com>>Reply-To:
              > nslu2-linux@yahoogroups.com <mailto:nslu2-linux%40yahoogroups.com>
              >
              > Hi,
              > >
              > >Finally I could make my Slug running properly with Unslug and the
              > packages
              > >Xinetd + Samba2 + Fuppes as I was expecting (Xinetd to have permanently
              > >TELNET loaded, it's more simple to use than Tssh on a pure private
              > >network).
              > >
              > >Now next step I want to take advantage of the mem upgrade I already
              > made up
              > >to 256MB (4 x 512mbit chips) and then running the same packages plus some
              > >others.
              > >I anticipate to run OpenWrt to try to run with no hard disks in a later
              > >stage (except the NAS where are stored the video files). (probably I'll
              > >have
              > >to upgrade to ObeseSlug if 8MB flash isn't sufficient).
              > >
              > >Where can I find an url on how to load APEX on top of Redboot before I
              > >switch to OpenWrt, I don't want to mix the problems... One at a time...
              > >I've tried to find something, I found many sites talking APEX but not one
              > >really good ( or unclear for me...) on how to keep Redboot below
              > APEX. Can
              > >you help?
              > >
              > >For info I wasn't able to mount under Unslung the NAS file system
              > with the
              > >command "mount -t smbfs .... ", it doesn't work with Unslung as it
              > should,
              > >I
              > >don't know why but nevermind I found a solution: I was forced to use the
              > >direct command "/usr/bin/smbmount //ip_nas/nas_filesystem_to_mount
              > >/mnt/...").
              > >This was the cause of my problem explained earlier.
              > >
              > >
              > >Many thanks.
              > >pf
              > >
              > >
              > >
              > >
              > >
              > >----- Original Message -----
              > >From: "Rod Whitby" <rod@... <mailto:rod%40whitby.id.au>>
              > >To: <nslu2-linux@yahoogroups.com <mailto:nslu2-linux%40yahoogroups.com>>
              > >Sent: Sunday, April 20, 2008 12:17 AM
              > >Subject: Re: [nslu2-linux] Hello and a small question concerning Unslung
              > >
              > >
              > >Put 'cat ' in front of each of your two commands.
              > >Note that you won't be able to use the 256MB with Unslung without
              > >recompiling a modified kernel source. Latest SlugOS and OpenWrt will
              > >definitely use it, and I think latest Debian will too.
              > >Also note there are still unresolved issues with mem > 64MB (search the
              > >mailing list archive at gmane.org for details).
              > >-- Rod
              > >
              > >-----Original Message-----
              > >From: "f5bqp_pfm" <pfmonet@... <mailto:pfmonet%40wanadoo.fr>>
              > >Date: Sunday, Apr 20, 2008 1:21 am
              > >Subject: [nslu2-linux] Hello and a small question concerning Unslung
              > >To: nslu2-linux@yahoogroups.comReply-To
              > <mailto:nslu2-linux%40yahoogroups.comReply-To>:
              > nslu2-linux@yahoogroups.com <mailto:nslu2-linux%40yahoogroups.com>
              > >
              > >
              > >>Hello to everyone,
              > >
              > >>As a new member and a new NSLU2 user I firstly want say hello to all
              > >of you, members of this fancy toy group... I hope you'll not have to
              > >suffer to much of some of my stupid questions... lol...
              > >
              > >>I've started to upgrade my slug up to 256MB to be able to work with
              > >enough space and I thank my binocular who helped greatly...
              > >Now I've intalled Unslung-6.10 to start to play with, as a first step.
              > >Then probably I'll switch to Debian, which probably is more a real
              > >Linux, but before I wanted to be sure to manage properly the slug and
              > >its capabilities.
              > >One thing at a time... but as from time to time I'm a Linux user I
              > >believe that Unslung will borrow me rather soon...
              > >Now the question:
              > >The first two commands I tried to type are /proc/meminfo and
              > >/proc/cpuinfo and I got a frustrating injure! Permission Denied! And I
              > >was logged as root. Then I've tried su to retype the commands same
              > >injure!
              > >Does this means that under Unslung-6.10 there is no way to be logged
              > >as Super User to be able to execute admin commands?
              > >
              > >>Thanks in advance for your help.
              > >
              > >>pf
              > >(Pierre-François)
              > >
              > >>
              > >
              > >>
              > >
              > >>------------------------------------
              > >
              > >>Yahoo! Groups Links
              > >
              > >>
              > >
              > >>
              > >
              > >
              > >------------------------------------
              > >
              > >Yahoo! Groups Links
              > >
              > >
              > >
              > >
              > >
              > >__________ Information NOD32 3040 (20080419) __________
              > >
              > >Ce message a ete verifie par NOD32 Antivirus System.
              > >http://www.nod32.com <http://www.nod32.com>
              > >
              > >
              > >
              > >
              > >------------------------------------
              > >
              > >Yahoo! Groups Links
              > >
              > >
              > >
              > >
              >
              > ------------------------------------
              >
              > Yahoo! Groups Links
              >
              > __________ Information NOD32 3072 (20080503) __________
              >
              > Ce message a ete verifie par NOD32 Antivirus System.
              > http://www.nod32.com <http://www.nod32.com>
              >
              >
              >
              > ------------------------------------------------------------------------
              >
              > Antivirus avast! <http://www.avast.com>: message Entrant sain.
              >
              > Base de donnees virale (VPS) : 080504-0, 04/05/2008
              > Analyse le : 05/05/2008 01:34:51
              > avast! - copyright (c) 1988-2008 ALWIL Software.
              >
              >
            • Rod Whitby
              ... I believe that 1.5.13 can detect both cases. ... Yes, this is the way you can intentionally limit it to 64MB. ... Then use use the setenv command on the
              Message 6 of 16 , May 5, 2008
              • 0 Attachment
                jean jacques goesens wrote:
                > The memory may be limited by two things:
                >
                > 1) It depends if APEX was compiled with 2 banks support or not, if compiled for only one bank,
                > the second (piggy pack) will be ignored.

                I believe that 1.5.13 can detect both cases.

                > 2) It depends also of the memscan command in the environment, it limits the memory
                > scan so extra memory is not detected.

                Yes, this is the way you can intentionally limit it to 64MB.

                > If it works, you can type the rest of the sequence manually to boot linux
                > and check if you get the whole intended memory.

                Then use use the setenv command on the apex console command line to
                change that command. No need to reflash.

                > I wrote a small batch in order to create the image.bin file, i need to find it on my slug:
                >
                > *#! /bin/sh
                > echo recuperation des blocks
                >
                > dd if=/dev/mtdblock0 of=block0.bin
                > dd if=/dev/mtdblock1 of=block1.bin
                > dd if=/dev/mtdblock2 of=block2.bin
                > dd if=/dev/mtdblock3 of=block3.bin
                > dd if=/dev/mtdblock4 of=block4.bin
                > dd if=/dev/mtdblock5 of=block5.bin
                >
                > echo creation de l image
                >
                > cat block0.bin block1.bin block2.bin block3.bin block4.bin block5.bin > image.bin

                You can simplify this to:

                cat /dev/mtdblock* > image.bin

                > Personally, i created as this two images, one with the 64M memory,
                > another with 256M-2 banks limitation.

                There is also an apex-env command which allows you to make this change
                from the linux userland command line. No need to reflash, just edit the
                apex environment and reboot.

                -- Rod
              Your message has been successfully submitted and would be delivered to recipients shortly.