Loading ...
Sorry, an error occurred while loading the content.

3026Re: Ntp

Expand Messages
  • maverik044
    Jan 1, 2005
      Now its off by 12 minutes

      ntpq -p
      remote refid st t when poll reach delay
      offset jitter
      =====================================================================
      =========
      time.nrc.ca 132.246.168.9 2 u 176 1024 377 19.339
      707870. 9946.39


      --- In nslu2-linux@yahoogroups.com, "maverik044" <maverik044@y...>
      wrote:
      >
      > Oddly enough the time is right, right now. I uninstalled the
      > package, installed ntpclient, uninstalled ntpclient, then
      installed
      > ntp to get the following:
      >
      > This is for 0.pool.ntp.org
      > 31 Dec 20:35:26 ntpdate[1430]: adjust time server 66.111.46.200
      > offset 0.075187 sec
      > 31 Dec 20:35:49 ntpdate[1432]: adjust time server 140.192.21.130
      > offset 0.357365 sec
      > 31 Dec 20:58:49 ntpdate[1454]: step time server 212.79.244.34
      offset
      > 0.581395 sec
      > 31 Dec 21:05:19 ntpdate[1455]: step time server 195.71.86.233
      offset
      > 3.773242 sec
      >
      >
      > time.nrc.ca
      > 31 Dec 20:37:21 ntpdate[1433]: step time server 132.246.168.148
      > offset 1.139684 sec
      > 31 Dec 20:57:48 ntpdate[1452]: step time server 132.246.168.164
      > offset 11.896307 sec
      > 31 Dec 20:58:33 ntpdate[1453]: adjust time server 132.246.168.164
      > offset 0.448963 sec
      > 31 Dec 21:05:30 ntpdate[1456]: adjust time server 132.246.168.164
      > offset 0.132328 sec
      >
      > Using ntpq -q
      > ntpq -p
      > remote refid st t when poll reach delay
      > offset jitter
      >
      =====================================================================
      > =========
      > gusi.leathercol 209.81.9.7 2 u 13 64 1 327.430
      > 324.059 0.061
      > 81-174-11-4.f5. 195.113.144.201 2 u 12 64 1 143.400
      > 323.362 0.061
      > ntp1.chorus.net .GPS. 1 u 11 64 1 30.039
      > 337.477 0.061
      >
      > ntpq -p
      > remote refid st t when poll reach delay
      > offset jitter
      >
      =====================================================================
      > =========
      > gusi.leathercol 209.81.9.7 2 u 30 64 3 327.430
      > 324.059 599.374
      > 81-174-11-4.f5. 195.113.144.201 2 u 30 64 3 143.400
      > 323.362 591.689
      > ntp1.chorus.net .GPS. 1 u 28 64 3 30.039
      > 337.477 596.739
      >
      >
      > remote refid st t when poll reach delay
      > offset jitter
      >
      =====================================================================
      > =========
      > time.nrc.ca 132.246.168.9 2 u 23 64 1 13.680
      > 2050.09 0.061
      >
      > remote refid st t when poll reach delay
      > offset jitter
      >
      =====================================================================
      > =========
      > time.nrc.ca 132.246.168.9 2 u 42 64 3 12.474
      > 2630.64 580.548
      >
      >
      > --- In nslu2-linux@yahoogroups.com, Lennert Buytenhek
      <buytenh@w...>
      > wrote:
      > > On Thu, Dec 30, 2004 at 11:23:10PM -0000, maverik044 wrote:
      > >
      > > > I've installed ntp 4.2.0, it does seem to be pulling the time
      > from
      > > > an ntp server (in my case time.nrc.ca), but its off by 5-8
      > minutes.
      > > > I've looked at
      > http://www.eecis.udel.edu/~mills/ntp/html/ntpd.html
      > > > and haven't found anything that explains it. Also tried
      > > > time.nist.gov, samething. Any suggestions?
      > >
      > > I had this problem because I was using hardfloat and the kernel
      > floating
      > > point emulator was not emulating the mnfd ('negate') opcode
      > correctly.
      > > ntp ended up adjusting the system time the wrong way because it
      > thought
      > > that -1.0 = 1.0!
      > >
      > > What does 'ntpdate time.nrc.ca' give for 'offset' (stop ntpd
      while
      > you
      > > do this)? What if you run it a few times in a row? And spaced
      > apart by
      > > a few minutes?
      > >
      > >
      > > --L
    • Show all 6 messages in this topic