Loading ...
Sorry, an error occurred while loading the content.

Re: [nslu2-general] problem with openslug + nslu2

Expand Messages
  • Ovidiu Sas
    Try to install another firmware and see if the issue persists. Maybe it s a hardware issue (bad memory??) -ovidiu
    Message 1 of 9 , Feb 23, 2013
    View Source
    • 0 Attachment
      Try to install another firmware and see if the issue persists.
      Maybe it's a hardware issue (bad memory??)

      -ovidiu

      On Sat, Feb 23, 2013 at 2:03 PM, Eric CS <erics324@...> wrote:
      >
      >
      >
      > I can do "ipkg update" succesfully the first time I reflashed openslug, but
      > then "ipkg upgrade" or "ipkg install x" fails.
      > maybe it's because I made the modification in resistance R83?
      >
      > 2013/2/23 Eric CS erics324@...>
      >
      >
      >
      > > I reinstalled the firmware and reunsling hard disk several times with the
      > > same result.
      > >
      > >
      > > 2013/2/23 Ovidiu Sas osas@...>
      > >
      > >> **
      > >>
      > >>
      > >> Try to re-unsling the hard drive and start fresh.
      > >> I have openslug installed on a NSLU a while ago and it is working fine.
      > >>
      > >> Regards,
      > >> Ovidiu Sas
      > >>
      > >>
      > >> On Fri, Feb 22, 2013 at 6:59 PM, Eric CS erics324@...> wrote:
      > >> >
      > >> >
      > >> >
      > >> > df command gives me this response
      > >> >
      > >> > Filesystem 1K-blocks Used Available Use% Mounted on
      > >> > /dev/root 6400 5468 932 85% /initrd
      > >> > /dev/sda1 384578164 251608 364791116 0% /
      > >> > /dev/sda1 384578164 251608 364791116 0% /dev/.static/dev
      > >> > udev 2048 36 2012 2% /dev
      > >> > tmpfs 15120 0 15120 0% /var/volatile
      > >> > tmpfs 15120 0 15120 0% /dev/shm
      > >> >
      > >> > I'm using an external hard drive 400 gb not think it's due to lack of
      > >> space
      > >> > .. perhaps the downloads directory hosts "ipkg" not correct? I've also
      > >> tried
      > >> > reinstalling "ipkg" but without success, when I try to use "ipkg" or
      > >> "ipkg-
      > >> > opt" the NSLU2 reboots itself.
      > >> >
      > >> > 2013/2/23 Anthony Takata htwiz2002@...>
      > >> >
      > >> > > **
      > >>
      > >> >
      > >> >
      > >> > >
      > >> > >
      > >> > > IIRC = If I Remember Correctly.
      > >> > > Make sure you have sufficient space on the disks (use the df command)
      > >> > > You can always try reinstalling ipkg, that won't harm anything.
      > >> > >
      > >> > >
      > >> > > On Fri, Feb 22, 2013 at 11:54 AM, Eric CS erics324@...> wrote:
      > >> > >
      > >> > > > **
      > >> > > >
      > >> > > >
      > >> > > > thanks for the reply.
      > >> > > > Yes I installed the firmware is Big endian think.
      > >> > > > In fact the first time I try to "opkg update" works fine but then
      > >> "opkg
      > >> > > > upgrade" the system hangs and reboots. I also managed to install
      > >> ipkg
      > >> > > with
      > >> > > > "setup-optware.sh" installs fine but when I do "ipkg update" the
      > >> system
      > >> > > > also
      > >> > > > hangs and reboots too.
      > >> > > > What is IIRC? how I can fix the kernel panic?
      > >> > > >
      > >> > > > 2013/2/22 Anthony Takata htwiz2002@...>
      > >> > > >
      > >> > > > > **
      > >> > >
      > >> > > >
      > >> > > > >
      > >> > > > >
      > >> > > > > Do you get any data back before it restarts? If it's causing a
      > >> kernel
      > >> > > > panic
      > >> > > > > that might be the cause.
      > >> > > > > I'm not familiar with openslug, but iirc you might need to make
      > >> sure
      > >> > > > > whether the programs you install are big-endian or little-endian
      > >> (I
      > >> > > think
      > >> > > > > the nslu2 is big endian by default?)
      > >> > > > >
      > >> > > > > On Fri, Feb 22, 2013 at 8:16 AM, Eric CS erics324@...>
      > >> wrote:
      > >> > > > >
      > >> > > > > > **
      > >> > > >
      > >> > > > >
      > >> > > > > >
      > >> > > > > >
      > >> > > > > > Hi all, I have a question about slugosBE 5.3 Beta and NSLU2. I
      > >> > > > installed
      > >> > > > > > the
      > >> > > > > > firmware with upslug2 successfully. I configured the network
      > >> with
      > >> > > > "turnup
      > >> > > > > > init" then I installed the system to my external hard drive 400
      > >> gb
      > >> > > > with "
      > >> > > > > > turnup disk-i / dev/sda1" then I created a swapfile file.
      > >> Everything
      > >> > > > fine
      > >> > > > > > until I try to use opkg or ipkg, when I use the command "opkg
      > >> update"
      > >> > > > > and "
      > >> > > > > > ipkg update" NSLU2 automatically restarts.
      > >> > > > > > I searched a lot on google but can not find solution. Someone
      > >> could
      > >> > > > give
      > >> > > > > > me a
      > >> > > > > > solution to solve this? thanks
    Your message has been successfully submitted and would be delivered to recipients shortly.