Loading ...
Sorry, an error occurred while loading the content.

suddenly nslu2 fails to mount drive1

Expand Messages
  • AETJansen
    Hi All, I have been using unslung for months without a problem. Until now. I switched on the nslu and both 250gb usb drives. But, it will mount drive2, but no
    Message 1 of 1 , Dec 5, 2005
    • 0 Attachment
      Hi All,

      I have been using unslung for months without a problem. Until now.

      I switched on the nslu and both 250gb usb drives. But, it will mount
      drive2, but no longer drive 1. the drive spins up, then after a couple
      seconds, it spins down again... when I switch off the nslu and switch
      on the drive again, it remains running.

      I disconnected both drives, then switched on the nslu, enabled telnet,
      telnetted into the nslu to see if I could find anything. But I dont
      know what to look for.

      I found this in the /var/messages file:

      <46>Dec 5 22:40:03 klogd: hub.c: new USB device 00:01.2-2, assigned
      address 3
      <44>Dec 5 22:40:03 klogd: Protocol: Transparent SCSI
      <44>Dec 5 22:40:03 klogd: before kernel thread
      <44>Dec 5 22:40:03 klogd: *** detect:usb-storage
      <44>Dec 5 22:40:03 klogd: * scsi_register: usb-storage-0,
      <44>Dec 5 22:40:03 klogd: * scsi_reg, hostno:0 prot is 50
      <44>Dec 5 22:40:03 klogd: * scsi_reg, retval->host_no:0
      <46>Dec 5 22:40:03 klogd: scsi0 : SCSI emulation for USB Mass Storage
      devices
      <44>Dec 5 22:40:03 klogd: ! scan_scsis
      <44>Dec 5 22:40:03 klogd: do read capacity!!!
      <44>Dec 5 22:40:03 klogd: read capacity ok!!!
      <44>Dec 5 22:40:03 klogd: The capacity is 488397169
      <44>Dec 5 22:40:03 klogd: *** 50
      <44>Dec 5 22:40:03 klogd: 32 port connect!!!!!
      <44>Dec 5 22:40:03 klogd: Vendor: WDC WD25 Model: 00JB-00GVA0
      Rev: 08.0
      <44>Dec 5 22:40:03 klogd: Type: Direct-Access
      ANSI SCSI revision: 02
      <44>Dec 5 22:40:03 klogd: the host no is 0
      <44>Dec 5 22:40:03 klogd: * sd_attach:1
      <44>Dec 5 22:40:03 klogd: Attached scsi disk sdb at scsi0, channel 0,
      id 0, lun 0
      <44>Dec 5 22:40:03 klogd: SCSI device sdb: 488397169 512-byte hdwr
      sectors (250059 MB)
      <46>Dec 5 22:40:03 klogd: Partition check:
      <46>Dec 5 22:40:03 klogd: sdb1 sdb2 sdb3
      <47>Dec 5 22:40:03 klogd: WARNING: USB Mass Storage data integrity
      not assured
      <47>Dec 5 22:40:03 klogd: USB Mass Storage device found at 3
      <46>Dec 5 22:40:08 klogd: kjournald starting. Commit interval 5 seconds
      <44>Dec 5 22:40:08 klogd: EXT3-fs warning: maximal mount count
      reached, running e2fsck is recommended
      <46>Dec 5 22:40:08 klogd: EXT3 FS 2.4-0.9.19, 19 August 2002 on
      sd(8,17), internal journal
      <46>Dec 5 22:40:08 klogd: EXT3-fs: recovery complete.
      <46>Dec 5 22:40:08 klogd: EXT3-fs: mounted filesystem with ordered
      data mode.
      <46>Dec 5 22:40:08 klogd: kjournald starting. Commit interval 5 seconds
      <44>Dec 5 22:40:08 klogd: EXT3-fs warning: checktime reached, running
      e2fsck is recommended
      <46>Dec 5 22:40:08 klogd: EXT3 FS 2.4-0.9.19, 19 August 2002 on
      sd(8,18), internal journal
      <46>Dec 5 22:40:08 klogd: EXT3-fs: recovery complete.
      <46>Dec 5 22:40:08 klogd: EXT3-fs: mounted filesystem with ordered
      data mode.
      <46>Dec 5 22:40:16 klogd: kjournald starting. Commit interval 5 seconds
      <46>Dec 5 22:40:16 klogd: EXT3 FS 2.4-0.9.19, 19 August 2002 on
      sd(8,18), internal journal
      <46>Dec 5 22:40:16 klogd: EXT3-fs: mounted filesystem with ordered
      data mode.
      <46>Dec 5 22:40:20 klogd: Adding Swap: 56220k swap-space (priority -1)
      <44>Dec 5 22:40:26 klogd: EXT3-fs warning: maximal mount count
      reached, running e2fsck is recommended
      <46>Dec 5 22:40:26 klogd: EXT3 FS 2.4-0.9.19, 19 August 2002 on
      sd(8,17), internal journal
      <78>Dec 5 22:40:59 cron[424]: loading crontab file /etc/crontab


      anyone got a clue what I should do?


      thanks!
      Arno
    Your message has been successfully submitted and would be delivered to recipients shortly.