Loading ...
Sorry, an error occurred while loading the content.

Re: [nslu2-general] Checking if rootfs is on disk after unslinging.

Expand Messages
  • Rod Whitby
    ... Correct. Look at the rootfs and / lines, and ignore the /initrd line. If the size of rootfs and / reflects the size of your disk s data partition, then
    Message 1 of 9 , Aug 1, 2005
    • 0 Attachment
      On 8/2/05, Mattias <mattias@...> wrote:
      > The row containing: /dev/sda1 9656956 45856
      > 9512992 0% /
      > must mean that my rootfs lies on usbdisk1 and partition 1 as it should,
      > or am I wrong?

      Correct. Look at the rootfs and / lines, and ignore the /initrd line.

      If the size of rootfs and / reflects the size of your disk's data
      partition, then you are good.

      Please add this to the FAQ.

      -- Rod
    • Mattias
      Hi, I read everywhere that i should check that the unslinging process worked and that the rootfs is actually on the disk and not in flash. But I do not seem to
      Message 2 of 9 , Aug 1, 2005
      • 0 Attachment
        Hi, I read everywhere that i should check that the unslinging process
        worked and that the rootfs is actually on the disk and not in flash.
        But I do not seem to understand exactly how I could determine it.
        This is how it looks now on my nslu when df is issued:

        Filesystem 1k-blocks Used Available Use%
        Mounted on
        rootfs 9656956 45856 9512992 0%
        /
        /dev/sda1 6528 5320 1208
        81% /initrd
        /dev/sda1 9656956 45856 9512992 0% /
        /dev/sda1 9656956 45856 9512992 0%
        /share/hdd/data
        /dev/sda2 123955 4142 118533 3%
        /share/hdd/conf

        The row containing: /dev/sda1 9656956 45856
        9512992 0% /
        must mean that my rootfs lies on usbdisk1 and partition 1 as it should,
        or am I wrong?

        Please advise so that I wont brick my nslu2.
        Best regards Mattias
      • mike_pruis
        ... 45856 ... should, ... And what do you do if the rootfs isnt on the new drive? I have upgraded firmware, unslung and all (and had drives not-attached when
        Message 3 of 9 , Aug 8, 2005
        • 0 Attachment
          --- In nslu2-general@yahoogroups.com, Rod Whitby <list.yahoo@r...> wrote:
          > On 8/2/05, Mattias <mattias@i...> wrote:
          > > The row containing: /dev/sda1 9656956
          45856
          > > 9512992 0% /
          > > must mean that my rootfs lies on usbdisk1 and partition 1 as it
          should,
          > > or am I wrong?
          >
          > Correct. Look at the rootfs and / lines, and ignore the /initrd line.
          >
          > If the size of rootfs and / reflects the size of your disk's data
          > partition, then you are good.
          >
          > Please add this to the FAQ.
          >
          > -- Rod

          And what do you do if the rootfs isnt on the new drive?
          I have upgraded firmware, unslung and all (and had drives not-attached
          when told) but the unsling script (probably) didn't work correctly?

          this is the result of the df command:
          # df
          Filesystem 1k-blocks Used Available Use% Mounted on
          rootfs 6528 5324 1204 82% /
          /dev/mtdblock4 6528 5324 1204 82% /
          /dev/sda1 299681 18359 278228 6% /share/hdd/data
          /dev/sda2 123923 4142 118502 3% /share/hdd/conf

          I want to unsling my 512MB memstick, which is on port 1 and formatted
          using the slug... copying of all files seemed to go okay and the
          script didn't show any error (as far as my newbie unix skilz would
          allow me to understand)...

          please help?

          greetz,

          Mike
        • Rod Whitby
          Did you reboot the slug (with the same disk attached to the same port) after running the unsling command? If so, and it still doesn t load the rootfs from the
          Message 4 of 9 , Aug 8, 2005
          • 0 Attachment
            Did you reboot the slug (with the same disk attached to the same port)
            after running the unsling command?

            If so, and it still doesn't load the rootfs from the external disk,
            please post the result of "ls -la /" and "ls -la /initrd".

            -- Rod

            On 8/9/05, mike_pruis <mike_pruis@...> wrote:
            > And what do you do if the rootfs isnt on the new drive?
            > I have upgraded firmware, unslung and all (and had drives not-attached
            > when told) but the unsling script (probably) didn't work correctly?
            >
            > this is the result of the df command:
            > # df
            > Filesystem 1k-blocks Used Available Use% Mounted on
            > rootfs 6528 5324 1204 82% /
            > /dev/mtdblock4 6528 5324 1204 82% /
            > /dev/sda1 299681 18359 278228 6% /share/hdd/data
            > /dev/sda2 123923 4142 118502 3% /share/hdd/conf
            >
            > I want to unsling my 512MB memstick, which is on port 1 and formatted
            > using the slug... copying of all files seemed to go okay and the
            > script didn't show any error (as far as my newbie unix skilz would
            > allow me to understand)...
          • mike_pruis
            Yep I did a reboot... in the mean time I have done the whole proces again (reflash/reformatted/re...): same problem... here my latest output - from before and
            Message 5 of 9 , Aug 9, 2005
            • 0 Attachment
              Yep I did a reboot...
              in the mean time I have done the whole proces again
              (reflash/reformatted/re...): same problem...
              here my latest output - from before and after the reboot...

              anyone have any ideas?

              >>>

              Rivendel login: root
              Password:
              No directory, logging in with HOME=/


              BusyBox v0.60.4 (2004.07.01-03:05+0000) Built-in shell (ash)
              Enter 'help' for a list of built-in commands.

              # /sbin/unsling disk1
              Target disk is /share/hdd/data
              Copying the complete rootfs from / to /share/hdd/data.
              19123 blocks
              Linking /usr/bin/ipkg executable on target disk.
              Creating /.sda1root to direct switchbox to boot from /share/hdd/data.
              # cp /etc/passwd /share/hdd/conf/passwd
              # df
              Filesystem 1k-blocks Used Available Use% Mounted on
              rootfs 6528 5324 1204 82% /
              /dev/mtdblock4 6528 5324 1204 82% /
              /dev/sda2 123923 4142 118502
              3% /share/hdd/conf
              /dev/sda1 299681 18239 278348
              6% /share/hdd/data
              #

              AFTER REBOOT >>>

              # df
              Filesystem 1k-blocks Used Available Use% Mounted on
              rootfs 6528 5324 1204 82% /
              /dev/mtdblock4 6528 5324 1204 82% /
              /dev/sda1 299681 18256 278331
              6% /share/hdd/data
              /dev/sda2 123923 4142 118502
              3% /share/hdd/conf
              # ls -la /
              drwxr-xr-x 1 root root 0 Aug 9 11:47 .
              drwxr-xr-x 1 root root 0 Aug 9 11:47 ..
              -rw-r--r-- 1 root root 1 Aug 9 11:47 .sda1root
              -rw-rw-r-- 1 root root 25 Jan 1 1970 .unslung
              drwxrwxr-x 1 root root 0 Jan 1 1970 bin
              drwxrwxr-x 1 root root 0 Jan 1 1970 dev
              drwxr-xr-x 1 root root 0 Jan 1 1970 dev.state
              drwxr-xr-x 1 root root 0 Aug 9 11:53 etc
              drwxrwxr-x 1 root root 0 Jan 1 1970 home
              drwxr-xr-x 1 root root 0 Jan 1 1970 initrd
              drwxrwxr-x 1 root root 0 Jan 1 1970 lib
              -rwxr-xr-x 1 root root 3685 Jan 1 1970 linuxrc
              drwxr-xr-x 1 root root 0 Jan 1 1970 lost+found
              drwxrwxr-x 1 root root 0 Jan 1 1970 mnt
              drwxrwxr-x 1 root root 0 Jan 1 1970 opt
              dr-xr-xr-x 52 root root 0 Jan 1 1970 proc
              drwxrwxr-x 1 root root 0 Jan 1 1970 sbin
              drwxrwxr-x 1 admin everyone 0 Aug 9 01:15 share
              drwxrwxrwt 1 root root 0 Aug 9 11:53 tmp
              drwxr-xr-x 1 root root 0 Jan 1 1970 unslung
              drwxr-xr-x 1 root root 0 Jan 1 1970 upload
              drwxrwxr-x 1 root root 0 Jan 1 1970 usr
              drwxrwxr-x 1 root root 0 Jan 1 1970 var
              drwxr-xr-x 1 root root 0 Jan 1 1970 var.state
              # ls -la /initrd
              drwxr-xr-x 1 root root 0 Jan 1 1970 .
              drwxr-xr-x 1 root root 0 Aug 9 11:47 ..




              --- In nslu2-general@yahoogroups.com, Rod Whitby <list.yahoo@r...>
              wrote:
              > Did you reboot the slug (with the same disk attached to the same
              port)
              > after running the unsling command?
              >
              > If so, and it still doesn't load the rootfs from the external disk,
              > please post the result of "ls -la /" and "ls -la /initrd".
              >
              > -- Rod
              >
              > On 8/9/05, mike_pruis <mike_pruis@h...> wrote:
              > > And what do you do if the rootfs isnt on the new drive?
              > > I have upgraded firmware, unslung and all (and had drives not-
              attached
              > > when told) but the unsling script (probably) didn't work
              correctly?
              > >
              > > this is the result of the df command:
              > > # df
              > > Filesystem 1k-blocks Used Available Use% Mounted on
              > > rootfs 6528 5324 1204 82% /
              > > /dev/mtdblock4 6528 5324 1204 82% /
              > > /dev/sda1 299681 18359 278228
              6% /share/hdd/data
              > > /dev/sda2 123923 4142 118502
              3% /share/hdd/conf
              > >
              > > I want to unsling my 512MB memstick, which is on port 1 and
              formatted
              > > using the slug... copying of all files seemed to go okay and the
              > > script didn't show any error (as far as my newbie unix skilz would
              > > allow me to understand)...
            • Inge B. Arnesen
              ... Yeah - probably a long shot, but it could be that the disk is not ready within the boot delay period, so the flash is started as rootfs instead as no disk
              Message 6 of 9 , Aug 9, 2005
              • 0 Attachment
                > Yep I did a reboot...
                > in the mean time I have done the whole proces again
                > (reflash/reformatted/re...): same problem...
                > here my latest output - from before and after the reboot...
                >
                > anyone have any ideas?

                Yeah - probably a long shot, but it could be that the disk is not ready
                within the boot delay period, so the flash is started as rootfs instead as
                no disk is detected. Then, when the disk becomes ready it generates the
                hd_conn pseudofile and is detected by the Linksys automount SW which then
                mounts it as usual (under /share/hdd).

                The reason I don't quite believe this is that the delay is already quite
                large. If you had a serial connnection (you don't, do you?) you could see
                the boot statements, but I don't think the echo-statements from /linuxrc
                is stored anywhere (help me out here guys)?

                best,

                -- Inge
              • Rod Whitby
                ... Reboot again, and as soon as you get in, grab the output from dmesg and post that here. That will identify whether it s a slow disk or not. BTW, we ll
                Message 7 of 9 , Aug 9, 2005
                • 0 Attachment
                  On 8/9/05, mike_pruis <mike_pruis@...> wrote:
                  > Yep I did a reboot...
                  > in the mean time I have done the whole proces again
                  > (reflash/reformatted/re...): same problem...
                  > here my latest output - from before and after the reboot...

                  Reboot again, and as soon as you get in, grab the output from "dmesg"
                  and post that here. That will identify whether it's a slow disk or
                  not.

                  BTW, we'll be asking you to write up these troubleshooting steps on the wiki ...

                  -- Rod
                • mike_pruis
                  ok guys/girls, thnx for the help.. I d be happy to update the wiki... as soon as I know how :-) I will at minimum present it in a readable form and hope
                  Message 8 of 9 , Aug 9, 2005
                  • 0 Attachment
                    ok guys/girls, thnx for the help.. I'd be happy to update the wiki...
                    as soon as I know how :-) I will at minimum present it in a readable
                    form and hope someone will help me wiki it...

                    Ok.. rebooted the slug, enabled telnet, logged in as root and did a
                    dmesg... and here's gibberish it returned (at least for me it is :-):


                    # dmesg
                    Linux version 2.4.22-xfs (unslung@...) (gcc version 3.4.4) #1
                    Sun Jun 12
                    21:17:17 PDT 2005
                    CPU: XScale-IXP425/IXC1100 revision 1
                    Machine: Intel IXDP425 Development Platform
                    Warning: bad configuration page, trying to continue
                    Security risk: creating user accessible mapping for 0x60000000 at
                    0xff00f000
                    Security risk: creating user accessible mapping for 0x51000000 at
                    0xf1000000
                    On node 0 totalpages: 8192
                    zone(0): 8192 pages.
                    zone(1): 0 pages.
                    zone(2): 0 pages.
                    Kernel command line: console=ttyS0,115200n8 root=/dev/mtdblock4
                    rootfstype=jffs2
                    rw init=/linuxrc mem=32M@0x00000000
                    Relocating machine vectors to 0xffff0000
                    Calibrating delay loop... 131.48 BogoMIPS
                    Memory: 32MB = 32MB total
                    Memory: 30276KB available (1582K code, 274K data, 244K init)
                    Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
                    Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
                    Mount cache hash table entries: 512 (order: 0, 4096 bytes)
                    Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
                    Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
                    POSIX conformance testing by UNIFIX
                    PCI Autoconfig: Found Bus 0, Device 1, Function 0
                    PCI Autoconfig: BAR 0, Mem, size=0x1000, address=0x4bfff000
                    PCI Autoconfig: Found Bus 0, Device 1, Function 1
                    PCI Autoconfig: BAR 0, Mem, size=0x1000, address=0x4bffe000
                    PCI Autoconfig: Found Bus 0, Device 1, Function 2
                    PCI Autoconfig: BAR 0, Mem, size=0x100, address=0x4bffdf00
                    PCI: bus0: Fast back to back transfers disabled
                    Linux NET4.0 for Linux 2.4
                    Based upon Swansea University Computer Society NET3.039
                    Initializing RT netlink socket
                    Starting kswapd
                    VFS: Disk quotas vdquot_6.5.1
                    Journalled Block Device driver loaded
                    devfs: v1.12c (20020818) Richard Gooch (rgooch@...)
                    devfs: boot_options: 0x0
                    Installing knfsd (copyright (C) 1996 okir@...).
                    JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis
                    Communications AB.
                    i2c-core.o: i2c core module
                    i2c-dev.o: i2c /dev entries driver module
                    i2c-core.o: driver i2c-dev dummy driver registered.
                    i2c-algo-bit.o: i2c bit algorithm module version 2.6.1 (20010830)
                    pty: 256 Unix98 ptys configured
                    Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ
                    SERIAL_PCI en
                    abled
                    ttyS00 at 0xff000003 (irq = 15) is a XScale UART
                    ttyS01 at 0xff001003 (irq = 13) is a XScale UART
                    RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
                    loop: loaded (max 8 devices)
                    SCSI subsystem driver Revision: 1.00
                    * host:<NULL>
                    IXP425 Flash: Found an alias at 0x800000 for the chip at 0x0
                    cfi_cmdset_0001: Erase suspend on write enabled
                    0: offset=0x0,size=0x20000,blocks=64
                    Using buffer write method
                    Creating 6 MTD partitions on "IXP425 Flash":
                    0x00000000-0x00040000 : "RedBoot"
                    0x00040000-0x00060000 : "SysConf"
                    0x00060000-0x00160000 : "Kernel"
                    0x00160000-0x00180000 : "Ramdisk"
                    0x00180000-0x007e0000 : "Flashdisk"
                    0x007e0000-0x00800000 : "FIS directory"
                    usb.c: registered new driver usbdevfs
                    usb.c: registered new driver hub
                    pci probe begin
                    ehci_hcd 00:01.2: NEC Corporation USB 2.0
                    ehci_hcd 00:01.2: irq 26, pci mem c3872f00
                    usb.c: new USB bus registered, assigned bus number 1
                    PCI: 00:01.2 PCI cache line size set incorrectly (0 bytes) by BIOS/FW.
                    PCI: 00:01.2 PCI cache line size corrected to 32.
                    ehci_hcd 00:01.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Jun-19/2.4
                    hub.c: USB hub found
                    hub.c: 5 ports detected
                    pci probe ok
                    host/usb-uhci.c: $Revision: 1.1 $ time 21:18:46 Jun 12 2005
                    host/usb-uhci.c: High bandwidth mode enabled
                    host/usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
                    host/usb-ohci.c: USB OHCI at membase 0xc387a000, IRQ 28
                    host/usb-ohci.c: usb-00:01.0, NEC Corporation USB
                    usb.c: new USB bus registered, assigned bus number 2
                    hub.c: USB hub found
                    hub.c: 3 ports detected
                    host/usb-ohci.c: USB OHCI at membase 0xc3880000, IRQ 27
                    host/usb-ohci.c: usb-00:01.1, NEC Corporation USB (#2)
                    usb.c: new USB bus registered, assigned bus number 3
                    hub.c: USB hub found
                    hub.c: 2 ports detected
                    Initializing USB Mass Storage driver...
                    usb.c: registered new driver usb-storage
                    USB Mass Storage support registered.
                    i2c-dev.o: Registered 'IXP425 I2C Adapter' as minor 0
                    i2c-core.o: adapter IXP425 I2C Adapter registered as adapter 0.
                    NET4: Linux TCP/IP 1.0 for NET4.0
                    IP Protocols: ICMP, UDP, TCP, IGMP
                    IP: routing cache hash table of 512 buckets, 4Kbytes
                    TCP: Hash tables configured (established 2048 bind 4096)
                    IP-Config: No network devices available.
                    NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
                    NetWinder Floating Point Emulator V0.97 (double precision)
                    VFS: Mounted root (jffs2 filesystem).
                    Freeing init memory: 244K
                    hub.c: new USB device 00:01.2-1, assigned address 2
                    Protocol: Transparent SCSI
                    before kernel thread
                    *** detect:usb-storage
                    * scsi_register: usb-storage-1,
                    * scsi_reg, hostno:1 prot is 49
                    * scsi_reg, retval->host_no:1
                    scsi1 : SCSI emulation for USB Mass Storage devices
                    ! scan_scsis
                    *** 49
                    31 port connect!!!!!
                    Vendor: Kingston Model: DataTraveler 2.0 Rev: 1.04
                    Type: Direct-Access ANSI SCSI revision: 02
                    the host no is 1
                    * sd_attach:0
                    Attached scsi removable disk sda at scsi1, channel 0, id 0, lun 0
                    SCSI device sda: 1003520 512-byte hdwr sectors (514 MB)
                    sda: Write Protect is off
                    Partition check:
                    /dev/scsi/host1/bus0/target0/lun0: p1 p2 p3
                    WARNING: USB Mass Storage data integrity not assured
                    USB Mass Storage device found at 2
                    Module init.
                    ixp425_eth:
                    Initializing IXP425 NPE Ethernet driver software v. 1.1
                    ixp425_eth: CPU clock speed (approx) = 0 MHz
                    [error] ixEthMiiPhyScan : unexpected Mii PHY ID 00008201
                    ixp425_eth: ixp0 is using the PHY at address 1
                    ixp425_eth: ixp1 is using the PHY at address 0
                    ixp425_eth: ixEthMiiLinkStatus failed on PHY0.
                    Can't determine
                    the auto negotiated parameters. Using default values.
                    enable_irq(22) unbalanced from c39451bc
                    X1226: I2C based RTC driver.
                    i2c-core.o: driver X1226 registered.
                    X1226: found X1226 on IXP425 I2C Adapter
                    i2c-core.o: client [X1226] registered to adapter [IXP425 I2C
                    Adapter](pos. 0).
                    atr is 20
                    kjournald starting. Commit interval 5 seconds
                    EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal
                    EXT3-fs: recovery complete.
                    EXT3-fs: mounted filesystem with ordered data mode.
                    kjournald starting. Commit interval 5 seconds
                    EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,2), internal journal
                    EXT3-fs: mounted filesystem with ordered data mode.
                    kjournald starting. Commit interval 5 seconds
                    EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,2), internal journal
                    EXT3-fs: mounted filesystem with ordered data mode.
                    Adding Swap: 63980k swap-space (priority -1)
                    EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal




                    --- In nslu2-general@yahoogroups.com, Rod Whitby <list.yahoo@r...> wrote:
                    > On 8/9/05, mike_pruis <mike_pruis@h...> wrote:
                    > > Yep I did a reboot...
                    > > in the mean time I have done the whole proces again
                    > > (reflash/reformatted/re...): same problem...
                    > > here my latest output - from before and after the reboot...
                    >
                    > Reboot again, and as soon as you get in, grab the output from "dmesg"
                    > and post that here. That will identify whether it's a slow disk or
                    > not.
                    >
                    > BTW, we'll be asking you to write up these troubleshooting steps on
                    the wiki ...
                    >
                    > -- Rod
                  • Petr Jakes
                    Hi all, I just want to know how the story from this posting ended up. I have got the same problem. I did follow up the Unslung-5.x Family Release README
                    Message 9 of 9 , Sep 7, 2005
                    • 0 Attachment
                      Hi all, I just want to know how the story from this posting ended up.
                      I have got the same problem. I did follow up the "Unslung-5.x Family
                      Release README INSTALLATION" precisely and carefully many times and
                      after reboot the rootfs is starting from the slug, not from the memory
                      stick.
                      Petr


                      --- In nslu2-general@yahoogroups.com, "mike_pruis" <mike_pruis@h...>
                      wrote:
                      > ok guys/girls, thnx for the help.. I'd be happy to update the wiki...
                      > as soon as I know how :-) I will at minimum present it in a readable
                      > form and hope someone will help me wiki it...
                      >
                      > Ok.. rebooted the slug, enabled telnet, logged in as root and did a
                      > dmesg... and here's gibberish it returned (at least for me it is :-):
                      >
                      >
                      > # dmesg
                      > Linux version 2.4.22-xfs (unslung@u...) (gcc version 3.4.4) #1
                      > Sun Jun 12
                      > 21:17:17 PDT 2005
                      > CPU: XScale-IXP425/IXC1100 revision 1
                      > Machine: Intel IXDP425 Development Platform
                      > Warning: bad configuration page, trying to continue
                      > Security risk: creating user accessible mapping for 0x60000000 at
                      > 0xff00f000
                      > Security risk: creating user accessible mapping for 0x51000000 at
                      > 0xf1000000
                      > On node 0 totalpages: 8192
                      > zone(0): 8192 pages.
                      > zone(1): 0 pages.
                      > zone(2): 0 pages.
                      > Kernel command line: console=ttyS0,115200n8 root=/dev/mtdblock4
                      > rootfstype=jffs2
                      > rw init=/linuxrc mem=32M@0x00000000
                      > Relocating machine vectors to 0xffff0000
                      > Calibrating delay loop... 131.48 BogoMIPS
                      > Memory: 32MB = 32MB total
                      > Memory: 30276KB available (1582K code, 274K data, 244K init)
                      > Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
                      > Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
                      > Mount cache hash table entries: 512 (order: 0, 4096 bytes)
                      > Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
                      > Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
                      > POSIX conformance testing by UNIFIX
                      > PCI Autoconfig: Found Bus 0, Device 1, Function 0
                      > PCI Autoconfig: BAR 0, Mem, size=0x1000, address=0x4bfff000
                      > PCI Autoconfig: Found Bus 0, Device 1, Function 1
                      > PCI Autoconfig: BAR 0, Mem, size=0x1000, address=0x4bffe000
                      > PCI Autoconfig: Found Bus 0, Device 1, Function 2
                      > PCI Autoconfig: BAR 0, Mem, size=0x100, address=0x4bffdf00
                      > PCI: bus0: Fast back to back transfers disabled
                      > Linux NET4.0 for Linux 2.4
                      > Based upon Swansea University Computer Society NET3.039
                      > Initializing RT netlink socket
                      > Starting kswapd
                      > VFS: Disk quotas vdquot_6.5.1
                      > Journalled Block Device driver loaded
                      > devfs: v1.12c (20020818) Richard Gooch (rgooch@a...)
                      > devfs: boot_options: 0x0
                      > Installing knfsd (copyright (C) 1996 okir@m...).
                      > JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis
                      > Communications AB.
                      > i2c-core.o: i2c core module
                      > i2c-dev.o: i2c /dev entries driver module
                      > i2c-core.o: driver i2c-dev dummy driver registered.
                      > i2c-algo-bit.o: i2c bit algorithm module version 2.6.1 (20010830)
                      > pty: 256 Unix98 ptys configured
                      > Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ
                      > SERIAL_PCI en
                      > abled
                      > ttyS00 at 0xff000003 (irq = 15) is a XScale UART
                      > ttyS01 at 0xff001003 (irq = 13) is a XScale UART
                      > RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
                      > loop: loaded (max 8 devices)
                      > SCSI subsystem driver Revision: 1.00
                      > * host:<NULL>
                      > IXP425 Flash: Found an alias at 0x800000 for the chip at 0x0
                      > cfi_cmdset_0001: Erase suspend on write enabled
                      > 0: offset=0x0,size=0x20000,blocks=64
                      > Using buffer write method
                      > Creating 6 MTD partitions on "IXP425 Flash":
                      > 0x00000000-0x00040000 : "RedBoot"
                      > 0x00040000-0x00060000 : "SysConf"
                      > 0x00060000-0x00160000 : "Kernel"
                      > 0x00160000-0x00180000 : "Ramdisk"
                      > 0x00180000-0x007e0000 : "Flashdisk"
                      > 0x007e0000-0x00800000 : "FIS directory"
                      > usb.c: registered new driver usbdevfs
                      > usb.c: registered new driver hub
                      > pci probe begin
                      > ehci_hcd 00:01.2: NEC Corporation USB 2.0
                      > ehci_hcd 00:01.2: irq 26, pci mem c3872f00
                      > usb.c: new USB bus registered, assigned bus number 1
                      > PCI: 00:01.2 PCI cache line size set incorrectly (0 bytes) by BIOS/FW.
                      > PCI: 00:01.2 PCI cache line size corrected to 32.
                      > ehci_hcd 00:01.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Jun-19/2.4
                      > hub.c: USB hub found
                      > hub.c: 5 ports detected
                      > pci probe ok
                      > host/usb-uhci.c: $Revision: 1.1 $ time 21:18:46 Jun 12 2005
                      > host/usb-uhci.c: High bandwidth mode enabled
                      > host/usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
                      > host/usb-ohci.c: USB OHCI at membase 0xc387a000, IRQ 28
                      > host/usb-ohci.c: usb-00:01.0, NEC Corporation USB
                      > usb.c: new USB bus registered, assigned bus number 2
                      > hub.c: USB hub found
                      > hub.c: 3 ports detected
                      > host/usb-ohci.c: USB OHCI at membase 0xc3880000, IRQ 27
                      > host/usb-ohci.c: usb-00:01.1, NEC Corporation USB (#2)
                      > usb.c: new USB bus registered, assigned bus number 3
                      > hub.c: USB hub found
                      > hub.c: 2 ports detected
                      > Initializing USB Mass Storage driver...
                      > usb.c: registered new driver usb-storage
                      > USB Mass Storage support registered.
                      > i2c-dev.o: Registered 'IXP425 I2C Adapter' as minor 0
                      > i2c-core.o: adapter IXP425 I2C Adapter registered as adapter 0.
                      > NET4: Linux TCP/IP 1.0 for NET4.0
                      > IP Protocols: ICMP, UDP, TCP, IGMP
                      > IP: routing cache hash table of 512 buckets, 4Kbytes
                      > TCP: Hash tables configured (established 2048 bind 4096)
                      > IP-Config: No network devices available.
                      > NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
                      > NetWinder Floating Point Emulator V0.97 (double precision)
                      > VFS: Mounted root (jffs2 filesystem).
                      > Freeing init memory: 244K
                      > hub.c: new USB device 00:01.2-1, assigned address 2
                      > Protocol: Transparent SCSI
                      > before kernel thread
                      > *** detect:usb-storage
                      > * scsi_register: usb-storage-1,
                      > * scsi_reg, hostno:1 prot is 49
                      > * scsi_reg, retval->host_no:1
                      > scsi1 : SCSI emulation for USB Mass Storage devices
                      > ! scan_scsis
                      > *** 49
                      > 31 port connect!!!!!
                      > Vendor: Kingston Model: DataTraveler 2.0 Rev: 1.04
                      > Type: Direct-Access ANSI SCSI revision: 02
                      > the host no is 1
                      > * sd_attach:0
                      > Attached scsi removable disk sda at scsi1, channel 0, id 0, lun 0
                      > SCSI device sda: 1003520 512-byte hdwr sectors (514 MB)
                      > sda: Write Protect is off
                      > Partition check:
                      > /dev/scsi/host1/bus0/target0/lun0: p1 p2 p3
                      > WARNING: USB Mass Storage data integrity not assured
                      > USB Mass Storage device found at 2
                      > Module init.
                      > ixp425_eth:
                      > Initializing IXP425 NPE Ethernet driver software v. 1.1
                      > ixp425_eth: CPU clock speed (approx) = 0 MHz
                      > [error] ixEthMiiPhyScan : unexpected Mii PHY ID 00008201
                      > ixp425_eth: ixp0 is using the PHY at address 1
                      > ixp425_eth: ixp1 is using the PHY at address 0
                      > ixp425_eth: ixEthMiiLinkStatus failed on PHY0.
                      > Can't determine
                      > the auto negotiated parameters. Using default values.
                      > enable_irq(22) unbalanced from c39451bc
                      > X1226: I2C based RTC driver.
                      > i2c-core.o: driver X1226 registered.
                      > X1226: found X1226 on IXP425 I2C Adapter
                      > i2c-core.o: client [X1226] registered to adapter [IXP425 I2C
                      > Adapter](pos. 0).
                      > atr is 20
                      > kjournald starting. Commit interval 5 seconds
                      > EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal
                      > EXT3-fs: recovery complete.
                      > EXT3-fs: mounted filesystem with ordered data mode.
                      > kjournald starting. Commit interval 5 seconds
                      > EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,2), internal journal
                      > EXT3-fs: mounted filesystem with ordered data mode.
                      > kjournald starting. Commit interval 5 seconds
                      > EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,2), internal journal
                      > EXT3-fs: mounted filesystem with ordered data mode.
                      > Adding Swap: 63980k swap-space (priority -1)
                      > EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal
                      >
                      >
                      >
                      >
                      > --- In nslu2-general@yahoogroups.com, Rod Whitby <list.yahoo@r...>
                      wrote:
                      > > On 8/9/05, mike_pruis <mike_pruis@h...> wrote:
                      > > > Yep I did a reboot...
                      > > > in the mean time I have done the whole proces again
                      > > > (reflash/reformatted/re...): same problem...
                      > > > here my latest output - from before and after the reboot...
                      > >
                      > > Reboot again, and as soon as you get in, grab the output from "dmesg"
                      > > and post that here. That will identify whether it's a slow disk or
                      > > not.
                      > >
                      > > BTW, we'll be asking you to write up these troubleshooting steps on
                      > the wiki ...
                      > >
                      > > -- Rod
                    Your message has been successfully submitted and would be delivered to recipients shortly.