Loading ...
Sorry, an error occurred while loading the content.

8903Re: [nslu2-general] problem with openslug + nslu2

Expand Messages
  • Eric CS
    Feb 23, 2013
      I reinstalled the firmware and reunsling hard disk several times with the
      same result.


      2013/2/23 Ovidiu Sas <osas@...>

      > **
      >
      >
      > Try to re-unsling the hard drive and start fresh.
      > I have openslug installed on a NSLU a while ago and it is working fine.
      >
      > Regards,
      > Ovidiu Sas
      >
      >
      > On Fri, Feb 22, 2013 at 6:59 PM, Eric CS erics324@...> wrote:
      > >
      > >
      > >
      > > df command gives me this response
      > >
      > > Filesystem 1K-blocks Used Available Use% Mounted on
      > > /dev/root 6400 5468 932 85% /initrd
      > > /dev/sda1 384578164 251608 364791116 0% /
      > > /dev/sda1 384578164 251608 364791116 0% /dev/.static/dev
      > > udev 2048 36 2012 2% /dev
      > > tmpfs 15120 0 15120 0% /var/volatile
      > > tmpfs 15120 0 15120 0% /dev/shm
      > >
      > > I'm using an external hard drive 400 gb not think it's due to lack of
      > space
      > > .. perhaps the downloads directory hosts "ipkg" not correct? I've also
      > tried
      > > reinstalling "ipkg" but without success, when I try to use "ipkg" or
      > "ipkg-
      > > opt" the NSLU2 reboots itself.
      > >
      > > 2013/2/23 Anthony Takata htwiz2002@...>
      > >
      > > > **
      >
      > >
      > >
      > > >
      > > >
      > > > IIRC = If I Remember Correctly.
      > > > Make sure you have sufficient space on the disks (use the df command)
      > > > You can always try reinstalling ipkg, that won't harm anything.
      > > >
      > > >
      > > > On Fri, Feb 22, 2013 at 11:54 AM, Eric CS erics324@...> wrote:
      > > >
      > > > > **
      > > > >
      > > > >
      > > > > thanks for the reply.
      > > > > Yes I installed the firmware is Big endian think.
      > > > > In fact the first time I try to "opkg update" works fine but then
      > "opkg
      > > > > upgrade" the system hangs and reboots. I also managed to install ipkg
      > > > with
      > > > > "setup-optware.sh" installs fine but when I do "ipkg update" the
      > system
      > > > > also
      > > > > hangs and reboots too.
      > > > > What is IIRC? how I can fix the kernel panic?
      > > > >
      > > > > 2013/2/22 Anthony Takata htwiz2002@...>
      > > > >
      > > > > > **
      > > >
      > > > >
      > > > > >
      > > > > >
      > > > > > Do you get any data back before it restarts? If it's causing a
      > kernel
      > > > > panic
      > > > > > that might be the cause.
      > > > > > I'm not familiar with openslug, but iirc you might need to make
      > sure
      > > > > > whether the programs you install are big-endian or little-endian (I
      > > > think
      > > > > > the nslu2 is big endian by default?)
      > > > > >
      > > > > > On Fri, Feb 22, 2013 at 8:16 AM, Eric CS erics324@...>
      > wrote:
      > > > > >
      > > > > > > **
      > > > >
      > > > > >
      > > > > > >
      > > > > > >
      > > > > > > Hi all, I have a question about slugosBE 5.3 Beta and NSLU2. I
      > > > > installed
      > > > > > > the
      > > > > > > firmware with upslug2 successfully. I configured the network with
      > > > > "turnup
      > > > > > > init" then I installed the system to my external hard drive 400
      > gb
      > > > > with "
      > > > > > > turnup disk-i / dev/sda1" then I created a swapfile file.
      > Everything
      > > > > fine
      > > > > > > until I try to use opkg or ipkg, when I use the command "opkg
      > update"
      > > > > > and "
      > > > > > > ipkg update" NSLU2 automatically restarts.
      > > > > > > I searched a lot on google but can not find solution. Someone
      > could
      > > > > give
      > > > > > > me a
      > > > > > > solution to solve this? thanks
      >
      >
      >


      [Non-text portions of this message have been removed]
    • Show all 9 messages in this topic