Loading ...
Sorry, an error occurred while loading the content.

Re: [new_distillers] Re: Pot still cap

Expand Messages
  • Alex
    Use bran paste. Keep a ball in hand during run. ... -- Sent from my Android phone with K-9 Mail. Please excuse my brevity. Use bran paste. Keep a ball in hand
    Message 1 of 8 , Oct 23, 2012
      Use bran paste. Keep a ball in hand during run.

      johnjab01 <johnjab01@...> wrote:

      Thanks for the reply Virgil,

      I responed to this once, but Yahoo must have glitched...

      I have my cap about done. It looks like a chimney pipe cap/plug. sticking off the top of the still. It came out fairly well, I cut the top rolled edge & handle off & crimped the cut edge. I will use flour paste for a better seal around the cap during the run.

      I am still contemplating my vapor escape. I really want to come off the top of the cap(bottom of bucket)because of the nice flate surface. I want to put a copper 90 degree fitting coming out of it which will attach to the copper worm. Do you think a 3/4" fitting out the top would suffice?

      To answer your question. I plan on running the unit hard with vinegar & salt to clean out any impurities that may have accumulated over the years. I plan on leaving the copper as-is I dont want to polish off any history of the still, just add more!

      Thanks again..........John

      --- In new_distillers@yahoogroups.com, virgil hoskins <varminteater2003@...> wrote:
      > Hi JJ,, that great that you found your top, and your on your way again
      > I was just a a shop tonight and seen a stainless steel dog water dish that would have worked
      > for a top,, so cool a copper pot sounds great ,, and for your question ,, your beautiful antique pot
      > pretty much had there liebig or steam cone/ or pipe came out the side to a thump keg and then to a cooling coil
      > and down into a barrel with water to cool the shine steam and then collected in jars or jugs.
      > just a good old family still.
      > now as you look farther into our stills you`ll find different still tops for different areas,,,
      > none were streight up pipes like the new reflux stills we have today.
      > my quetion back toyou is how are you going to clean your pot out before you use it ,, and how?
      > next ,, are you going to shine the outside as well or keep it antique?
      > virgil
      > ________________________________
      > From: johnjab01 <johnjab01@...>
      > To: new_distillers@yahoogroups.com
      > Sent: Thursday, October 18, 2012 2:07 PM
      > Subject: [new_distillers] Re: Pot still cap
      > OK...I'm in the process of making my own cap. One question I have, should I have the cap discharge out the top, or out the side? I found a 6" dia copper bucket that I'm going to modify to fit, so the top of the cap will be the flat bottom of the bucket.
      > I have seen stills discharge out the top & out the side. Which do you think is best, or does it really matter?
      > Thanks....JJ
      > --- In mailto:new_distillers%40yahoogroups.com, virgil hoskins <varminteater2003@> wrote:
      > >
      > > Good morning JJ
      > > Well it looks like a high dollar fix to plug a hole that size,, would you be willing to cut the threaded area
      > > out/ off and replate it with a 2in, threaded hole ?,, is the area rounded or flat?
      > > if its flat you can have the hole tapped already before installing it,
      > > if it is a round area, the plate may have to be installed first then taped/ well or soldered in place
      > > to form with the curved area,, and i dont like the idea of using brass in a still ,,copper or stainless only
      > > let us know what you come up with,,do you have a machine shop close to you?
      > > they will tap your 2in, hole pretty fast ,
      > > virgil
      > >
      > >
      > > ________________________________
      > > From: johnjab01 <johnjab01@>
      > > To: mailto:new_distillers%40yahoogroups.com
      > > Sent: Thursday, October 11, 2012 3:16 PM
      > > Subject: [new_distillers] Pot still cap
      > >
      > >  
      > > Does anyone have a good source for brass/copper threaded caps? I dug up an old pot still that has a threaded opening of 5 13/16". I'm trying to come up with a cap to make it functional again.
      > >
      > > Thanks......JJ
      > >

      Sent from my Android phone with K-9 Mail. Please excuse my brevity.
    Your message has been successfully submitted and would be delivered to recipients shortly.