Loading ...
Sorry, an error occurred while loading the content.

Re: [mill_drill] Re: Grizzly G1006 Reversing drum switch

Expand Messages
  • Druid Noibn
    Hi GP,   Yes, indeed... The utility companies can be rather difficult at times and it is very difficult to get the folks to change their minds.    If one
    Message 1 of 17 , Jul 7, 2013
      Hi GP,
      Yes, indeed... The utility companies can be rather difficult at times and it is very difficult to get the folks to change their minds. 
      If one really wants the utility company to consider bringing the power over (the cost can be a surprise - depending on teh factors involved) one might ask the town board for a variance on the property.  For a residential area, the chance is very low.  Sometimes one might see some success IF...you can demonstrate that there would be no increase in traffic, no trucks (other than the usual USPS, UPS, FedEx and rare other delieveries...) and no increase in pedestrian trafic, e.g., not open to the public.  
      It's easier to get a converter <smile>  The VFDs that I have all worked well, so far. 
      Be well,

      From: Guenther Paul <paulguenter@...>
      To: "mill_drill@yahoogroups.com" <mill_drill@yahoogroups.com>
      Sent: Saturday, July 6, 2013 5:06 PM
      Subject: Re: [mill_drill] Re: Grizzly G1006 Reversing drum switch
      I have 3phase on the pole across the street, The power company will not hook up 3-phase to my property i am zoned
      agricultural-residential  i would need at least a light commercial zoning. Acutely i am fine all my machines i have now run a single phase but that may change ho knows i may get a machine with a 3phase
      From: Druid Noibn <druid_noibn@...>
      To: "mill_drill@yahoogroups.com" <mill_drill@yahoogroups.com>
      Sent: Saturday, July 6, 2013 4:48 PM
      Subject: Re: [mill_drill] Re: Grizzly G1006 Reversing drum switch
      Hi GP,
      Interesting question, one that an engineer is likely to ask <smile>
      We see lots of comments on this point, all good of course, but's let's stick with our engineering. 
      First - let's consider the approach to get 3-phase power 1) ask the power company to run a 3-phase line to our facilities and a licensed electrician to install the wiring (FYI, in NJ two folks can do the internal wiring on a home - the home owner or a licensed electrician); 2) get a rotary converter; 3) get a static converter; 4) get a VFD.  The last few points "assumes" that one has the appropriate power wired into the shop. 
      Item 1 is very good - and can be rather expensive as it depends a lot on what is available in your area.  I would have to pay, to have a power line brought in from a couple of blocks away.  Considering potential use - the utility company would not be eager to do it and it would be expensive. 
      Item 2- rotary converters are motor/generators (motoralternators if you wish) - they are very nice and lets one get full 3-pahse power.  Bigger is not always better and some control might be in order - not likley an issue for our needs and they are very reliable.  Probably best to find a good used one, as they can be expensive.
      Item 3 - static converters - they are sized to a particular motor size, and supply about 66% of the rated power - use only if forced to.  Look up as to what they really are <smile> - make your own.
      Item  4 - VFD - these are adjustable electronically controled converters - takes in AC converts it to DC and converts that back to AC; and are very efficient at doing so.  I'll leave it up to others to look up the specs on a few noting their total power consumption and conversion - they are efficient.  The output is variable, i.e., you can adjust the output such that it will allow the "motor" to vary it speed over a wide range.  It is not generally recommented to run multiple motors concurrently, although it can be done.  DO NOT put a switch, circuit breaket, relay, contactor or other disconnect device between the motor and the VFD.  For those areas when the safety rule demands a disconnect here - read the manual - some system permit a disconnect X milleseconds after interrupting the main power input. Cost...? varies with size of VFD and manufacturer - consider $130-$450 for the ones we typically need 
      Now, what the heck does the above have to do with the question? <smile>  
      The cost of 3-phase power depends on the approach used and it isn't only the $/KWH but also the cost of equipment needed. 
      Why did a fellow like me switch to a 3-phase system when I certainly know that it would not improve my work?  Because, I wanted to - it is a part of the fun I get working in my shop; and it is a part of my learning.  Heck, look at the speed adjustments on typical system, we may have "Low, Medium and High" yet we go a bit crazy discussing SFM (surface feet per minute) cutting speeds; an issue better left for those in production manufacturing. 
      I hope the above was of some interest.
      Kind regards,

      From: Guenther Paul <paulguenter@...>
      To: "mill_drill@yahoogroups.com" <mill_drill@yahoogroups.com>
      Sent: Friday, July 5, 2013 11:44 AM
      Subject: Re: [mill_drill] Re: Grizzly G1006 Reversing drum switch
      Did you all ever figure the operating cost i mean the cosumtion of elec. to convert single to 3 phase.
      From: wjhaasman <brianomcp@...>
      To: mill_drill@yahoogroups.com
      Sent: Friday, July 5, 2013 11:26 AM
      Subject: [mill_drill] Re: Grizzly G1006 Reversing drum switch
      What I meant was; Get a 3 phase motor with a phase converter to run on 240V household current then add a VFD for speed control. Cash permitting that is.
    Your message has been successfully submitted and would be delivered to recipients shortly.