Loading ...
Sorry, an error occurred while loading the content.
 

Re: [mill_drill] Big Red Cuck dont come out

Expand Messages
  • Guenther Paul
    I was in a hurry sorry. I did get the chuck  out of the arbor after all of this. The chuck arbor did not have a tang at all. It was taped out to a 10 mm x 1.5
    Message 1 of 10 , Mar 25, 2013
      I was in a hurry sorry. I did get the chuck  out of the arbor after all of this. The chuck arbor did not have a tang at all. It was taped out to a 10 mm x 1.5 thread. I guess i have to buy a tang stile arbor. I took a 1/4 piece of flat stock filed a knob on it the with of the tang and laid it on top of the arbor in the spindle. The drift wedge took it right out, i am all set.  I just bought big red about 4 weeks ago and have not messed with it.
      GP

       


      From: FocusKnobs <focusknobs@...>
      To: mill_drill@yahoogroups.com
      Sent: Mon, March 25, 2013 3:57:13 PM
      Subject: RE: [mill_drill] Big Red Cuck dont come out

       

      Well, at least the misspelling had a “u”, and not an “o”. <g>

       

      From: mill_drill@yahoogroups.com [mailto:mill_drill@yahoogroups.com] On Behalf Of Barry Kneller
      Sent: Monday, March 25, 2013 12:48 PM
      To: mill_drill@yahoogroups.com
      Subject: Re: [mill_drill] Big Red Cuck dont come out

       




      On 25/03/2013 19:35, Guenther Paul wrote:

      Miss spell in the head line sorry
       

      GP

       

       

      Could have been worse, co-- instead of cu-- ...........  :0)



    • Guenther Paul
      Thanks Bill I did about the same as you suggest except i used 1/4 flat stock GP ________________________________ From: Bill Armstrong
      Message 2 of 10 , Mar 25, 2013
        Thanks Bill
        I did about the same as you suggest except i used 1/4 flat stock 
        GP



        From: Bill Armstrong <bill_1955@...>
        To: "mill_drill@yahoogroups.com" <mill_drill@yahoogroups.com>
        Sent: Mon, March 25, 2013 3:40:42 PM
        Subject: Re: [mill_drill] Big Red Cuck dont come out

         

        Been there.....
        I've used a ball bearing, or a piece of key-stock, or flatbar, sitting on the end of the arbor, and use a morse taper wedge like normal.

        Bill

        Sent from my iPad

        On Mar 25, 2013, at 12:25 PM, "Guenther P" <paulguenter@...> wrote:

         

        How can i get the chuck out of the spindle ? Thers is no tang on the chuck arbor. The top of the chuck arbor is flush with the bottom of
        the slot in the spindle
        Thanks

      • Guenther Paul
        I called Grizzly for some other parts and asked about the G0517 was told the that machine came with a 12 mm draw bar. The G0517 is the same as big red as far
        Message 3 of 10 , Mar 25, 2013
          I called Grizzly for some other parts and asked about the G0517 was told the that machine came with a 12 mm draw bar. The G0517 is the same as big red as far as i can tell , there is no way one could use a 12 mm draw bar on big red
          Looking at a dimensional drawing of the spindle of G0517 it is just like big  red except its the Grizzly version
           
          GP



          From: Guenther Paul <paulguenter@...>
          To: mill_drill@yahoogroups.com
          Sent: Mon, March 25, 2013 4:48:58 PM
          Subject: Re: [mill_drill] Big Red Cuck dont come out

           

          Thanks Bill
          I did about the same as you suggest except i used 1/4 flat stock 
          GP



          From: Bill Armstrong <bill_1955@...>
          To: "mill_drill@yahoogroups.com" <mill_drill@yahoogroups.com>
          Sent: Mon, March 25, 2013 3:40:42 PM
          Subject: Re: [mill_drill] Big Red Cuck dont come out

           

          Been there.....
          I've used a ball bearing, or a piece of key-stock, or flatbar, sitting on the end of the arbor, and use a morse taper wedge like normal.

          Bill

          Sent from my iPad

          On Mar 25, 2013, at 12:25 PM, "Guenther P" <paulguenter@...> wrote:

           

          How can i get the chuck out of the spindle ? Thers is no tang on the chuck arbor. The top of the chuck arbor is flush with the bottom of
          the slot in the spindle
          Thanks

        • Carl Hollopeter
          GP’ Get a short 10 mm x 1.5 bolt, a socket head would probably be ideal, if not get a Phillips head. Turn or file or grind the head to slightly smaller than
          Message 4 of 10 , Mar 25, 2013
            GP’
               Get a short 10 mm x 1.5 bolt, a socket head would probably be ideal, if not get a Phillips head. Turn or file or grind the head to slightly smaller than the diameter of the small end of the arbor and screw it in the end. Now when the arbor is seated the bolt head will be protruding up into the slot and your wedge should work fine from now on.
            Carl H
             
            Sent: Monday, March 25, 2013 3:43 PM
            Subject: Re: [mill_drill] Big Red Cuck dont come out
             
             

            I was in a hurry sorry. I did get the chuck  out of the arbor after all of this. The chuck arbor did not have a tang at all. It was taped out to a 10 mm x 1.5 thread. I guess i have to buy a tang stile arbor. I took a 1/4 piece of flat stock filed a knob on it the with of the tang and laid it on top of the arbor in the spindle. The drift wedge took it right out, i am all set.  I just bought big red about 4 weeks ago and have not messed with it.
            GP

             
             

            From: FocusKnobs <focusknobs@...>
            To: mill_drill@yahoogroups.com
            Sent: Mon, March 25, 2013 3:57:13 PM
            Subject: RE: [mill_drill] Big Red Cuck dont come out

             

            Well, at least the misspelling had a “u”, and not an “o”. <g>

             

            From: mill_drill@yahoogroups.com [mailto:mill_drill@yahoogroups.com] On Behalf Of Barry Kneller
            Sent: Monday, March 25, 2013 12:48 PM
            To: mill_drill@yahoogroups.com
            Subject: Re: [mill_drill] Big Red Cuck dont come out

             




            On 25/03/2013 19:35, Guenther Paul wrote:

            Miss spell in the head line sorry
             

            GP

             

             

            Could have been worse, co-- instead of cu-- ...........  :0)



          • Guenther Paul
            Thanks Carl I was thinking the same way. A bolt is a lot cheaper as a new chuck arbor  GP ________________________________ From: Carl Hollopeter
            Message 5 of 10 , Mar 25, 2013
              Thanks Carl
              I was thinking the same way. A bolt is a lot cheaper as a new chuck arbor
               
              GP



              From: Carl Hollopeter <chollo@...>
              To: mill_drill@yahoogroups.com
              Sent: Mon, March 25, 2013 7:23:46 PM
              Subject: Re: [mill_drill] Big Red Cuck dont come out

               

              GP’
                 Get a short 10 mm x 1.5 bolt, a socket head would probably be ideal, if not get a Phillips head. Turn or file or grind the head to slightly smaller than the diameter of the small end of the arbor and screw it in the end. Now when the arbor is seated the bolt head will be protruding up into the slot and your wedge should work fine from now on.
              Carl H
               
              Sent: Monday, March 25, 2013 3:43 PM
              Subject: Re: [mill_drill] Big Red Cuck dont come out
               
               

              I was in a hurry sorry. I did get the chuck  out of the arbor after all of this. The chuck arbor did not have a tang at all. It was taped out to a 10 mm x 1.5 thread. I guess i have to buy a tang stile arbor. I took a 1/4 piece of flat stock filed a knob on it the with of the tang and laid it on top of the arbor in the spindle. The drift wedge took it right out, i am all set.  I just bought big red about 4 weeks ago and have not messed with it.
              GP

               
               

              From: FocusKnobs <focusknobs@...>
              To: mill_drill@yahoogroups.com
              Sent: Mon, March 25, 2013 3:57:13 PM
              Subject: RE: [mill_drill] Big Red Cuck dont come out

               

              Well, at least the misspelling had a “u”, and not an “o”. <g>

               

              From: mill_drill@yahoogroups.com [mailto:mill_drill@yahoogroups.com] On Behalf Of Barry Kneller
              Sent: Monday, March 25, 2013 12:48 PM
              To: mill_drill@yahoogroups.com
              Subject: Re: [mill_drill] Big Red Cuck dont come out

               




              On 25/03/2013 19:35, Guenther Paul wrote:

              Miss spell in the head line sorry
               

              GP

               

               

              Could have been worse, co-- instead of cu-- ...........  :0)



            Your message has been successfully submitted and would be delivered to recipients shortly.