Loading ...
Sorry, an error occurred while loading the content.

Re: [mill_drill] new article: Drilling a Hexagonal Hole

Expand Messages
  • John
    Hey Rick,I don t have the mating part in front of me, but IIRC it was about a 7/16 hex.  It just needed to be a slip fit, so I m not too worried about
    Message 1 of 24 , Feb 28 10:51 PM
    • 0 Attachment

      Hey Rick,

      I don't have the mating part in front of me, but IIRC it was about a 7/16" hex.  It just needed to be a slip fit, so I'm not too worried about tolerances.  I was thinking I'd go a little bigger on the holes for the corners and use a small file to make the flats a little "flatter" after the center drill operation.  

      -John



      --- On Sun, 2/24/13, Rick Sparber <rgsparber@...> wrote:

      From: Rick Sparber <rgsparber@...>
      Subject: Re: [mill_drill] new article: Drilling a Hexagonal Hole
      To: "mill_drill@yahoogroups.com" <mill_drill@yahoogroups.com>
      Date: Sunday, February 24, 2013, 3:57 AM

       
      John,

      Glad to be of service.  What size hex do you plan to drill?

      Rick

      On Feb 24, 2013, at 2:57 AM, John <jennasys@...> wrote:

      Awesome.  I have a project where I need to make a single hex hole and this will work beautifully.  I had already planned on using a similar technique, but this spells out exactly what I need to do.  Thanks for posting it!

      -John



      --- On Tue, 2/19/13, Rick Sparber <rgsparber@...> wrote:

      From: Rick Sparber <rgsparber@...>
      Subject: [mill_drill] new article: Drilling a Hexagonal Hole
      To: valleymetal@yahoogroups.com, mill_drill@yahoogroups.com, smithy-machines@yahoogroups.com, 3_in_1_Lathe_Mill_Drill@yahoogroups.com
      Date: Tuesday, February 19, 2013, 9:22 AM

       

      This article, intended for those new to our hobby of metalworking, explains how you can drill a hole with a hexagonal cross section. I provide all needed dimensions for a ¼” hex bit plus the math enabling you to drill any size polygon.

       

      If you are interested, please see

       

      http://rick.sparber.org/dhh.pdf

       

      Your comments and questions are welcome. All of us are smarter than any one of us.

       

      For the full index of my articles, see rick.sparber.org.

       

      Rick

    • Rick Sparber
      John, I was going to write up the general case as an article but then realized there is no general case. You just have to pick drill sizes that take out the
      Message 2 of 24 , Mar 2, 2013
      • 0 Attachment

        John,

         

        I was going to write up the general case as an article but then realized there is no general case. You just have to pick drill sizes that take out the most material.

         

        Rick

         

        From: mill_drill@yahoogroups.com [mailto:mill_drill@yahoogroups.com] On Behalf Of John
        Sent: Thursday, February 28, 2013 11:52 PM
        To: mill_drill@yahoogroups.com
        Subject: Re: [mill_drill] new article: Drilling a Hexagonal Hole

         




        Hey Rick,

        I don't have the mating part in front of me, but IIRC it was about a 7/16" hex.  It just needed to be a slip fit, so I'm not too worried about tolerances.  I was thinking I'd go a little bigger on the holes for the corners and use a small file to make the flats a little "flatter" after the center drill operation.  

        -John

         


        --- On Sun, 2/24/13, Rick Sparber <rgsparber@...> wrote:


        From: Rick Sparber <rgsparber@...>
        Subject: Re: [mill_drill] new article: Drilling a Hexagonal Hole
        To: "mill_drill@yahoogroups.com" <mill_drill@yahoogroups.com>
        Date: Sunday, February 24, 2013, 3:57 AM

         

        John,

         

        Glad to be of service.  What size hex do you plan to drill?

         

        Rick


        On Feb 24, 2013, at 2:57 AM, John <jennasys@...> wrote:

        Awesome.  I have a project where I need to make a single hex hole and this will work beautifully.  I had already planned on using a similar technique, but this spells out exactly what I need to do.  Thanks for posting it!

        -John

         


        --- On Tue, 2/19/13, Rick Sparber <rgsparber@...> wrote:


        From: Rick Sparber <rgsparber@...>
        Subject: [mill_drill] new article: Drilling a Hexagonal Hole
        To: valleymetal@yahoogroups.com, mill_drill@yahoogroups.com, smithy-machines@yahoogroups.com, 3_in_1_Lathe_Mill_Drill@yahoogroups.com
        Date: Tuesday, February 19, 2013, 9:22 AM

         

        This article, intended for those new to our hobby of metalworking, explains how you can drill a hole with a hexagonal cross section. I provide all needed dimensions for a ¼” hex bit plus the math enabling you to drill any size polygon.

         

        If you are interested, please see

         

        http://rick.sparber.org/dhh.pdf

         

        Your comments and questions are welcome. All of us are smarter than any one of us.

         

        For the full index of my articles, see rick.sparber.org.

         

        Rick




      • Guenther Paul
        Hey Rick Havent seen you here bevore. Have you bean here a while ?  GP ________________________________ From: Rick Sparber To:
        Message 3 of 24 , Mar 2, 2013
        • 0 Attachment
          Hey Rick
          Havent seen you here bevore. Have you bean here a while ?
           
          GP



          From: Rick Sparber <rgsparber@...>
          To: mill_drill@yahoogroups.com
          Sent: Sat, March 2, 2013 9:16:04 PM
          Subject: RE: [mill_drill] new article: Drilling a Hexagonal Hole

           

          John,

           

          I was going to write up the general case as an article but then realized there is no general case. You just have to pick drill sizes that take out the most material.

           

          Rick

           

          From: mill_drill@yahoogroups.com [mailto:mill_drill@yahoogroups.com] On Behalf Of John
          Sent: Thursday, February 28, 2013 11:52 PM
          To: mill_drill@yahoogroups.com
          Subject: Re: [mill_drill] new article: Drilling a Hexagonal Hole

           




          Hey Rick,

          I don't have the mating part in front of me, but IIRC it was about a 7/16" hex.  It just needed to be a slip fit, so I'm not too worried about tolerances.  I was thinking I'd go a little bigger on the holes for the corners and use a small file to make the flats a little "flatter" after the center drill operation.  

          -John

           


          --- On Sun, 2/24/13, Rick Sparber <rgsparber@...> wrote:


          From: Rick Sparber <rgsparber@...>
          Subject: Re: [mill_drill] new article: Drilling a Hexagonal Hole
          To: "mill_drill@yahoogroups.com" <mill_drill@yahoogroups.com>
          Date: Sunday, February 24, 2013, 3:57 AM

           

          John,

           

          Glad to be of service.  What size hex do you plan to drill?

           

          Rick


          On Feb 24, 2013, at 2:57 AM, John <jennasys@...> wrot




        • Rick Sparber
          GP, I’ve been here a while but spent so much time on my Electronic Edge Finders, there wasn’t much time left over for milling. I think I’m done with
          Message 4 of 24 , Mar 2, 2013
          • 0 Attachment

            GP,

             

            I’ve been here a while but spent so much time on my Electronic Edge Finders, there wasn’t much time left over for milling. I think I’m done with electronics for a while but can never be sure what my next project will be.

             

            My web site does have an entire section devoted to mill attachments and another for mill technique:

             

            http://rick.sparber.org/ma.htm

             

            Rick

             

            From: mill_drill@yahoogroups.com [mailto:mill_drill@yahoogroups.com] On Behalf Of Guenther Paul
            Sent: Saturday, March 02, 2013 7:48 PM
            To: mill_drill@yahoogroups.com
            Subject: Re: [mill_drill] new article: Drilling a Hexagonal Hole

             




            Hey Rick

            Havent seen you here bevore. Have you bean here a while ?
             

            GP

             

             


            From: Rick Sparber <rgsparber@...>
            To: mill_drill@yahoogroups.com
            Sent: Sat, March 2, 2013 9:16:04 PM
            Subject: RE: [mill_drill] new article: Drilling a Hexagonal Hole

             

            John,

             

            I was going to write up the general case as an article but then realized there is no general case. You just have to pick drill sizes that take out the most material.

             

            Rick

             

            From: mill_drill@yahoogroups.com [mailto:mill_drill@yahoogroups.com] On Behalf Of John
            Sent: Thursday, February 28, 2013 11:52 PM
            To: mill_drill@yahoogroups.com
            Subject: Re: [mill_drill] new article: Drilling a Hexagonal Hole

             



            Hey Rick,

            I don't have the mating part in front of me, but IIRC it was about a 7/16" hex.  It just needed to be a slip fit, so I'm not too worried about tolerances.  I was thinking I'd go a little bigger on the holes for the corners and use a small file to make the flats a little "flatter" after the center drill operation.  

            -John

             


            --- On Sun, 2/24/13, Rick Sparber <rgsparber@...> wrote:


            From: Rick Sparber <rgsparber@...>
            Subject: Re: [mill_drill] new article: Drilling a Hexagonal Hole
            To: "mill_drill@yahoogroups.com" <mill_drill@yahoogroups.com>
            Date: Sunday, February 24, 2013, 3:57 AM

             

            John,

             

            Glad to be of service.  What size hex do you plan to drill?

             

            Rick


            On Feb 24, 2013, at 2:57 AM, John <jennasys@...> wrot






          • John
            If I get some time, I ll try and write up a little program to calculate drill sizes to get the best fit/require the least amount of cleanup.John ... From: Rick
            Message 5 of 24 , Mar 2, 2013
            • 0 Attachment

              If I get some time, I'll try and write up a little program to calculate drill sizes to get the best fit/require the least amount of cleanup.

              John


              --- On Sat, 3/2/13, Rick Sparber <rgsparber@...> wrote:

              From: Rick Sparber <rgsparber@...>
              Subject: RE: [mill_drill] new article: Drilling a Hexagonal Hole
              To: mill_drill@yahoogroups.com
              Date: Saturday, March 2, 2013, 6:15 PM

               

              John,

               

              I was going to write up the general case as an article but then realized there is no general case. You just have to pick drill sizes that take out the most material.

               

              Rick

               

              From: mill_drill@yahoogroups.com [mailto:mill_drill@yahoogroups.com] On Behalf Of John
              Sent: Thursday, February 28, 2013 11:52 PM
              To: mill_drill@yahoogroups.com
              Subject: Re: [mill_drill] new article: Drilling a Hexagonal Hole

               




              Hey Rick,

              I don't have the mating part in front of me, but IIRC it was about a 7/16" hex.  It just needed to be a slip fit, so I'm not too worried about tolerances.  I was thinking I'd go a little bigger on the holes for the corners and use a small file to make the flats a little "flatter" after the center drill operation.  

              -John

               


              --- On Sun, 2/24/13, Rick Sparber <rgsparber@...> wrote:


              From: Rick Sparber <rgsparber@...>
              Subject: Re: [mill_drill] new article: Drilling a Hexagonal Hole
              To: "mill_drill@yahoogroups.com" <mill_drill@yahoogroups.com>
              Date: Sunday, February 24, 2013, 3:57 AM

               

              John,

               

              Glad to be of service.  What size hex do you plan to drill?

               

              Rick


              On Feb 24, 2013, at 2:57 AM, John <jennasys@...> wrote:

              Awesome.  I have a project where I need to make a single hex hole and this will work beautifully.  I had already planned on using a similar technique, but this spells out exactly what I need to do.  Thanks for posting it!

              -John

               


              --- On Tue, 2/19/13, Rick Sparber <rgsparber@...> wrote:


              From: Rick Sparber <rgsparber@...>
              Subject: [mill_drill] new article: Drilling a Hexagonal Hole
              To: valleymetal@yahoogroups.com, mill_drill@yahoogroups.com, smithy-machines@yahoogroups.com, 3_in_1_Lathe_Mill_Drill@yahoogroups.com
              Date: Tuesday, February 19, 2013, 9:22 AM

               

              This article, intended for those new to our hobby of metalworking, explains how you can drill a hole with a hexagonal cross section. I provide all needed dimensions for a ¼” hex bit plus the math enabling you to drill any size polygon.

               

              If you are interested, please see

               

              http://rick.sparber.org/dhh.pdf

               

              Your comments and questions are welcome. All of us are smarter than any one of us.

               

              For the full index of my articles, see rick.sparber.org.

               

              Rick




            • Rick Sparber
              John, That would be very impressive. Rick ... John, That would be very impressive. Rick On Mar 2, 2013, at 9:26 PM, John wrote: If I get
              Message 6 of 24 , Mar 2, 2013
              • 0 Attachment
                John,

                That would be very impressive.

                Rick

                On Mar 2, 2013, at 9:26 PM, John <jennasys@...> wrote:

                If I get some time, I'll try and write up a little program to calculate drill sizes to get the best fit/require the least amount of cleanup.

                John


                --- On Sat, 3/2/13, Rick Sparber <rgsparber@...> wrote:

                From: Rick Sparber <rgsparber@...>
                Subject: RE: [mill_drill] new article: Drilling a Hexagonal Hole
                To: mill_drill@yahoogroups.com
                Date: Saturday, March 2, 2013, 6:15 PM

                 

                John,

                 

                I was going to write up the general case as an article but then realized there is no general case. You just have to pick drill sizes that take out the most material.

                 

                Rick

                 

                From: mill_drill@yahoogroups.com [mailto:mill_drill@yahoogroups.com] On Behalf Of John
                Sent: Thursday, February 28, 2013 11:52 PM
                To: mill_drill@yahoogroups.com
                Subject: Re: [mill_drill] new article: Drilling a Hexagonal Hole

                 




                Hey Rick,

                I don't have the mating part in front of me, but IIRC it was about a 7/16" hex.  It just needed to be a slip fit, so I'm not too worried about tolerances.  I was thinking I'd go a little bigger on the holes for the corners and use a small file to make the flats a little "flatter" after the center drill operation.  

                -John

                 


                --- On Sun, 2/24/13, Rick Sparber <rgsparber@...> wrote:


                From: Rick Sparber <rgsparber@...>
                Subject: Re: [mill_drill] new article: Drilling a Hexagonal Hole
                To: "mill_drill@yahoogroups.com" <mill_drill@yahoogroups.com>
                Date: Sunday, February 24, 2013, 3:57 AM

                 

                John,

                 

                Glad to be of service.  What size hex do you plan to drill?

                 

                Rick


                On Feb 24, 2013, at 2:57 AM, John <jennasys@...> wrote:

                Awesome.  I have a project where I need to make a single hex hole and this will work beautifully.  I had already planned on using a similar technique, but this spells out exactly what I need to do.  Thanks for posting it!

                -John

                 


                --- On Tue, 2/19/13, Rick Sparber <rgsparber@...> wrote:


                From: Rick Sparber <rgsparber@...>
                Subject: [mill_drill] new article: Drilling a Hexagonal Hole
                To: valleymetal@yahoogroups.com, mill_drill@yahoogroups.com, smithy-machines@yahoogroups.com, 3_in_1_Lathe_Mill_Drill@yahoogroups.com
                Date: Tuesday, February 19, 2013, 9:22 AM

                 

                This article, intended for those new to our hobby of metalworking, explains how you can drill a hole with a hexagonal cross section. I provide all needed dimensions for a ¼” hex bit plus the math enabling you to drill any size polygon.

                 

                If you are interested, please see

                 

                http://rick.sparber.org/dhh.pdf

                 

                Your comments and questions are welcome. All of us are smarter than any one of us.

                 

                For the full index of my articles, see rick.sparber.org.

                 

                Rick




              • John
                Hey Rick, I just started going through the theory section in your paper - should the initial calculation for the hypotenuse (center to hex corner) be:   1/8
                Message 7 of 24 , Mar 5, 2013
                • 0 Attachment

                  Hey Rick, I just started going through the theory section in your paper - should the initial calculation for the hypotenuse (center to hex corner) be: 

                    1/8 / cos(30)

                  instead of:

                    1/8 x cos(30)


                  -John


                  --- On Sat, 3/2/13, Rick Sparber <rgsparber@...> wrote:

                  From: Rick Sparber <rgsparber@...>
                  Subject: Re: [mill_drill] new article: Drilling a Hexagonal Hole
                  To: "mill_drill@yahoogroups.com" <mill_drill@yahoogroups.com>
                  Date: Saturday, March 2, 2013, 8:27 PM

                   
                  John,

                  That would be very impressive.

                  Rick

                  On Mar 2, 2013, at 9:26 PM, John <jennasys@...> wrote:

                  If I get some time, I'll try and write up a little program to calculate drill sizes to get the best fit/require the least amount of cleanup.

                  John


                  --- On Sat, 3/2/13, Rick Sparber <rgsparber@...> wrote:

                  From: Rick Sparber <rgsparber@...>
                  Subject: RE: [mill_drill] new article: Drilling a Hexagonal Hole
                  To: mill_drill@yahoogroups.com
                  Date: Saturday, March 2, 2013, 6:15 PM

                   

                  John,

                   

                  I was going to write up the general case as an article but then realized there is no general case. You just have to pick drill sizes that take out the most material.

                   

                  Rick

                   

                  From: mill_drill@yahoogroups.com [mailto:mill_drill@yahoogroups.com] On Behalf Of John
                  Sent: Thursday, February 28, 2013 11:52 PM
                  To: mill_drill@yahoogroups.com
                  Subject: Re: [mill_drill] new article: Drilling a Hexagonal Hole

                   




                  Hey Rick,

                  I don't have the mating part in front of me, but IIRC it was about a 7/16" hex.  It just needed to be a slip fit, so I'm not too worried about tolerances.  I was thinking I'd go a little bigger on the holes for the corners and use a small file to make the flats a little "flatter" after the center drill operation.  

                  -John

                   


                  --- On Sun, 2/24/13, Rick Sparber <rgsparber@...> wrote:


                  From: Rick Sparber <rgsparber@...>
                  Subject: Re: [mill_drill] new article: Drilling a Hexagonal Hole
                  To: "mill_drill@yahoogroups.com" <mill_drill@yahoogroups.com>
                  Date: Sunday, February 24, 2013, 3:57 AM

                   

                  John,

                   

                  Glad to be of service.  What size hex do you plan to drill?

                   

                  Rick


                  On Feb 24, 2013, at 2:57 AM, John <jennasys@...> wrote:

                  Awesome.  I have a project where I need to make a single hex hole and this will work beautifully.  I had already planned on using a similar technique, but this spells out exactly what I need to do.  Thanks for posting it!

                  -John

                   


                  --- On Tue, 2/19/13, Rick Sparber <rgsparber@...> wrote:


                  From: Rick Sparber <rgsparber@...>
                  Subject: [mill_drill] new article: Drilling a Hexagonal Hole
                  To: valleymetal@yahoogroups.com, mill_drill@yahoogroups.com, smithy-machines@yahoogroups.com, 3_in_1_Lathe_Mill_Drill@yahoogroups.com
                  Date: Tuesday, February 19, 2013, 9:22 AM

                   

                  This article, intended for those new to our hobby of metalworking, explains how you can drill a hole with a hexagonal cross section. I provide all needed dimensions for a ¼” hex bit plus the math enabling you to drill any size polygon.

                   

                  If you are interested, please see

                   

                  http://rick.sparber.org/dhh.pdf

                   

                  Your comments and questions are welcome. All of us are smarter than any one of us.

                   

                  For the full index of my articles, see rick.sparber.org.

                   

                  Rick




                • Rick Sparber
                  John, Thanks for catching the error. It is now fixed plus I made the equations look a little better: http://rick.sparber.org/dhh.pdf The figures are right,
                  Message 8 of 24 , Mar 6, 2013
                  • 0 Attachment

                    John,

                     

                    Thanks for catching the error. It is now fixed plus I made the equations look a little better:

                     

                    http://rick.sparber.org/dhh.pdf

                     

                    The figures are right, only the equations were wrong.

                     

                    Rick

                     

                    From: mill_drill@yahoogroups.com [mailto:mill_drill@yahoogroups.com] On Behalf Of John
                    Sent: Tuesday, March 05, 2013 4:58 PM
                    To: mill_drill@yahoogroups.com
                    Subject: Re: [mill_drill] new article: Drilling a Hexagonal Hole

                     




                    Hey Rick, I just started going through the theory section in your paper - should the initial calculation for the hypotenuse (center to hex corner) be: 

                      1/8 / cos(30)

                    instead of:

                      1/8 x cos(30)

                     

                    -John


                    --- On Sat, 3/2/13, Rick Sparber <rgsparber@...> wrote:


                    From: Rick Sparber <rgsparber@...>
                    Subject: Re: [mill_drill] new article: Drilling a Hexagonal Hole
                    To: "mill_drill@yahoogroups.com" <mill_drill@yahoogroups.com>
                    Date: Saturday, March 2, 2013, 8:27 PM

                     

                    John,


                    That would be very impressive.

                    Rick


                    On Mar 2, 2013, at 9:26 PM, John <jennasys@...> wrote:

                    If I get some time, I'll try and write up a little program to calculate drill sizes to get the best fit/require the least amount of cleanup.

                    John


                    --- On Sat, 3/2/13, Rick Sparber <rgsparber@...> wrote:


                    From: Rick Sparber <rgsparber@...>
                    Subject: RE: [mill_drill] new article: Drilling a Hexagonal Hole
                    To: mill_drill@yahoogroups.com
                    Date: Saturday, March 2, 2013, 6:15 PM

                     

                    John,

                     

                    I was going to write up the general case as an article but then realized there is no general case. You just have to pick drill sizes that take out the most material.

                     

                    Rick

                     

                    From: mill_drill@yahoogroups.com [mailto:mill_drill@yahoogroups.com] On Behalf Of John
                    Sent: Thursday, February 28, 2013 11:52 PM
                    To: mill_drill@yahoogroups.com
                    Subject: Re: [mill_drill] new article: Drilling a Hexagonal Hole

                     



                    Hey Rick,

                    I don't have the mating part in front of me, but IIRC it was about a 7/16" hex.  It just needed to be a slip fit, so I'm not too worried about tolerances.  I was thinking I'd go a little bigger on the holes for the corners and use a small file to make the flats a little "flatter" after the center drill operation.  

                    -John

                     


                    --- On Sun, 2/24/13, Rick Sparber <rgsparber@...> wrote:


                    From: Rick Sparber <rgsparber@...>
                    Subject: Re: [mill_drill] new article: Drilling a Hexagonal Hole
                    To: "mill_drill@yahoogroups.com" <mill_drill@yahoogroups.com>
                    Date: Sunday, February 24, 2013, 3:57 AM

                     

                    John,

                     

                    Glad to be of service.  What size hex do you plan to drill?

                     

                    Rick


                    On Feb 24, 2013, at 2:57 AM, John <jennasys@...> wrote:

                    Awesome.  I have a project where I need to make a single hex hole and this will work beautifully.  I had already planned on using a similar technique, but this spells out exactly what I need to do.  Thanks for posting it!

                    -John

                     


                    --- On Tue, 2/19/13, Rick Sparber <rgsparber@...> wrote:


                    From: Rick Sparber <rgsparber@...>
                    Subject: [mill_drill] new article: Drilling a Hexagonal Hole
                    To: valleymetal@yahoogroups.com, mill_drill@yahoogroups.com, smithy-machines@yahoogroups.com, 3_in_1_Lathe_Mill_Drill@yahoogroups.com
                    Date: Tuesday, February 19, 2013, 9:22 AM

                     

                    This article, intended for those new to our hobby of metalworking, explains how you can drill a hole with a hexagonal cross section. I provide all needed dimensions for a ¼” hex bit plus the math enabling you to drill any size polygon.

                     

                    If you are interested, please see

                     

                    http://rick.sparber.org/dhh.pdf

                     

                    Your comments and questions are welcome. All of us are smarter than any one of us.

                     

                    For the full index of my articles, see rick.sparber.org.

                     

                    Rick






                  • John
                    So instead of doing real work for the past day or so, I went ahead and wrote a program to calculate and visualize the drilled hex holes based on fractional
                    Message 9 of 24 , Mar 7, 2013
                    • 1 Attachment
                    • 40 KB

                    So instead of doing real work for the past day or so, I went ahead and wrote a program to calculate and visualize the drilled hex holes based on fractional drill sizes (screenshot is attached).  I'd be more than happy to share it, though I wrote it in Python and I'm not sure if that's a deal killer for the folks here.  Mac and Linux come with Python pre-installed, and I believe I can make a stand alone EXE file for windows if desired.  Worst case I can possibly even port it into Javascript so that it can be run in a web browser.


                    Anyway, I'm just trying to figure out the best way to get it into the hands of anyone that wants it.  What does everyone think?


                    -John



                    --- On Wed, 3/6/13, Rick Sparber <rgsparber@...> wrote:

                    From: Rick Sparber <rgsparber@...>
                    Subject: RE: [mill_drill] new article: Drilling a Hexagonal Hole
                    To: mill_drill@yahoogroups.com
                    Date: Wednesday, March 6, 2013, 6:42 AM

                     

                    John,

                     

                    Thanks for catching the error. It is now fixed plus I made the equations look a little better:

                     

                    http://rick.sparber.org/dhh.pdf

                     

                    The figures are right, only the equations were wrong.

                     

                    Rick

                     

                    From: mill_drill@yahoogroups.com [mailto:mill_drill@yahoogroups.com] On Behalf Of John
                    Sent: Tuesday, March 05, 2013 4:58 PM
                    To: mill_drill@yahoogroups.com
                    Subject: Re: [mill_drill] new article: Drilling a Hexagonal Hole

                     




                    Hey Rick, I just started going through the theory section in your paper - should the initial calculation for the hypotenuse (center to hex corner) be: 

                      1/8 / cos(30)

                    instead of:

                      1/8 x cos(30)

                     

                    -John


                    --- On Sat, 3/2/13, Rick Sparber <rgsparber@...> wrote:


                    From: Rick Sparber <rgsparber@...>
                    Subject: Re: [mill_drill] new article: Drilling a Hexagonal Hole
                    To: "mill_drill@yahoogroups.com" <mill_drill@yahoogroups.com>
                    Date: Saturday, March 2, 2013, 8:27 PM

                     

                    John,


                    That would be very impressive.

                    Rick


                    On Mar 2, 2013, at 9:26 PM, John <jennasys@...> wrote:

                    If I get some time, I'll try and write up a little program to calculate drill sizes to get the best fit/require the least amount of cleanup.

                    John


                    --- On Sat, 3/2/13, Rick Sparber <rgsparber@...> wrote:


                    From: Rick Sparber <rgsparber@...>
                    Subject: RE: [mill_drill] new article: Drilling a Hexagonal Hole
                    To: mill_drill@yahoogroups.com
                    Date: Saturday, March 2, 2013, 6:15 PM

                     

                    John,

                     

                    I was going to write up the general case as an article but then realized there is no general case. You just have to pick drill sizes that take out the most material.

                     

                    Rick

                     

                    From: mill_drill@yahoogroups.com [mailto:mill_drill@yahoogroups.com] On Behalf Of John
                    Sent: Thursday, February 28, 2013 11:52 PM
                    To: mill_drill@yahoogroups.com
                    Subject: Re: [mill_drill] new article: Drilling a Hexagonal Hole

                     



                    Hey Rick,

                    I don't have the mating part in front of me, but IIRC it was about a 7/16" hex.  It just needed to be a slip fit, so I'm not too worried about tolerances.  I was thinking I'd go a little bigger on the holes for the corners and use a small file to make the flats a little "flatter" after the center drill operation.  

                    -John

                     


                    --- On Sun, 2/24/13, Rick Sparber <rgsparber@...> wrote:


                    From: Rick Sparber <rgsparber@...>
                    Subject: Re: [mill_drill] new article: Drilling a Hexagonal Hole
                    To: "mill_drill@yahoogroups.com" <mill_drill@yahoogroups.com>
                    Date: Sunday, February 24, 2013, 3:57 AM

                     

                    John,

                     

                    Glad to be of service.  What size hex do you plan to drill?

                     

                    Rick


                    On Feb 24, 2013, at 2:57 AM, John <jennasys@...> wrote:

                    Awesome.  I have a project where I need to make a single hex hole and this will work beautifully.  I had already planned on using a similar technique, but this spells out exactly what I need to do.  Thanks for posting it!

                    -John

                     


                    --- On Tue, 2/19/13, Rick Sparber <rgsparber@...> wrote:


                    From: Rick Sparber <rgsparber@...>
                    Subject: [mill_drill] new article: Drilling a Hexagonal Hole
                    To: valleymetal@yahoogroups.com, mill_drill@yahoogroups.com, smithy-machines@yahoogroups.com, 3_in_1_Lathe_Mill_Drill@yahoogroups.com
                    Date: Tuesday, February 19, 2013, 9:22 AM

                     

                    This article, intended for those new to our hobby of metalworking, explains how you can drill a hole with a hexagonal cross section. I provide all needed dimensions for a ¼” hex bit plus the math enabling you to drill any size polygon.

                     

                    If you are interested, please see

                     

                    http://rick.sparber.org/dhh.pdf

                     

                    Your comments and questions are welcome. All of us are smarter than any one of us.

                     

                    For the full index of my articles, see rick.sparber.org.

                     

                    Rick






                  • Rick Sparber
                    John, This is a good start but there is more to it. If the flat to flat distance is ¼”, then using 1/16” holes plus a ¼” center hole is good enough.
                    Message 10 of 24 , Mar 7, 2013
                    • 0 Attachment

                      John,

                       

                      This is a good start but there is more to it. If the flat to flat distance is ¼”, then using 1/16” holes plus a ¼” center hole is good enough. But as you go to larger flat to flat distances, more small holes are needed to minimize error.

                       

                      The challenge is to calculate the diameter and location of these small holes. They will not all be 1/16”.

                       

                      Rick

                       

                      From: mill_drill@yahoogroups.com [mailto:mill_drill@yahoogroups.com] On Behalf Of John
                      Sent: Thursday, March 07, 2013 3:32 AM
                      To: mill_drill@yahoogroups.com
                      Subject: RE: [mill_drill] new article: Drilling a Hexagonal Hole [1 Attachment]

                       

                      [Attachment(s) from John included below]


                      So instead of doing real work for the past day or so, I went ahead and wrote a program to calculate and visualize the drilled hex holes based on fractional drill sizes (screenshot is attached).  I'd be more than happy to share it, though I wrote it in Python and I'm not sure if that's a deal killer for the folks here.  Mac and Linux come with Python pre-installed, and I believe I can make a stand alone EXE file for windows if desired.  Worst case I can possibly even port it into Javascript so that it can be run in a web browser.

                       

                      Anyway, I'm just trying to figure out the best way to get it into the hands of anyone that wants it.  What does everyone think?

                       

                      -John

                       


                      --- On Wed, 3/6/13, Rick Sparber <rgsparber@...> wrote:


                      From: Rick Sparber <rgsparber@...>
                      Subject: RE: [mill_drill] new article: Drilling a Hexagonal Hole
                      To: mill_drill@yahoogroups.com
                      Date: Wednesday, March 6, 2013, 6:42 AM

                       

                      John,

                       

                      Thanks for catching the error. It is now fixed plus I made the equations look a little better:

                       

                      http://rick.sparber.org/dhh.pdf

                       

                      The figures are right, only the equations were wrong.

                       

                      Rick

                       

                      From: mill_drill@yahoogroups.com [mailto:mill_drill@yahoogroups.com] On Behalf Of John
                      Sent: Tuesday, March 05, 2013 4:58 PM
                      To: mill_drill@yahoogroups.com
                      Subject: Re: [mill_drill] new article: Drilling a Hexagonal Hole

                       



                      Hey Rick, I just started going through the theory section in your paper - should the initial calculation for the hypotenuse (center to hex corner) be: 

                        1/8 / cos(30)

                      instead of:

                        1/8 x cos(30)

                       

                      -John


                      --- On Sat, 3/2/13, Rick Sparber <rgsparber@...> wrote:


                      From: Rick Sparber <rgsparber@...>
                      Subject: Re: [mill_drill] new article: Drilling a Hexagonal Hole
                      To: "mill_drill@yahoogroups.com" <mill_drill@yahoogroups.com>
                      Date: Saturday, March 2, 2013, 8:27 PM

                       

                      John,


                      That would be very impressive.

                      Rick


                      On Mar 2, 2013, at 9:26 PM, John <jennasys@...> wrote:

                      If I get some time, I'll try and write up a little program to calculate drill sizes to get the best fit/require the least amount of cleanup.

                      John


                      --- On Sat, 3/2/13, Rick Sparber <rgsparber@...> wrote:


                      From: Rick Sparber <rgsparber@...>
                      Subject: RE: [mill_drill] new article: Drilling a Hexagonal Hole
                      To: mill_drill@yahoogroups.com
                      Date: Saturday, March 2, 2013, 6:15 PM

                       

                      John,

                       

                      I was going to write up the general case as an article but then realized there is no general case. You just have to pick drill sizes that take out the most material.

                       

                      Rick

                       

                      From: mill_drill@yahoogroups.com [mailto:mill_drill@yahoogroups.com] On Behalf Of John
                      Sent: Thursday, February 28, 2013 11:52 PM
                      To: mill_drill@yahoogroups.com
                      Subject: Re: [mill_drill] new article: Drilling a Hexagonal Hole

                       

                       

                      Hey Rick,

                      I don't have the mating part in front of me, but IIRC it was about a 7/16" hex.  It just needed to be a slip fit, so I'm not too worried about tolerances.  I was thinking I'd go a little bigger on the holes for the corners and use a small file to make the flats a little "flatter" after the center drill operation.  

                      -John

                       


                      --- On Sun, 2/24/13, Rick Sparber <rgsparber@...> wrote:


                      From: Rick Sparber <rgsparber@...>
                      Subject: Re: [mill_drill] new article: Drilling a Hexagonal Hole
                      To: "mill_drill@yahoogroups.com" <mill_drill@yahoogroups.com>
                      Date: Sunday, February 24, 2013, 3:57 AM

                       

                      John,

                       

                      Glad to be of service.  What size hex do you plan to drill?

                       

                      Rick


                      On Feb 24, 2013, at 2:57 AM, John <jennasys@...> wrote:

                      Awesome.  I have a project where I need to make a single hex hole and this will work beautifully.  I had already planned on using a similar technique, but this spells out exactly what I need to do.  Thanks for posting it!

                      -John

                       


                      --- On Tue, 2/19/13, Rick Sparber <rgsparber@...> wrote:


                      From: Rick Sparber <rgsparber@...>
                      Subject: [mill_drill] new article: Drilling a Hexagonal Hole
                      To: valleymetal@yahoogroups.com, mill_drill@yahoogroups.com, smithy-machines@yahoogroups.com, 3_in_1_Lathe_Mill_Drill@yahoogroups.com
                      Date: Tuesday, February 19, 2013, 9:22 AM

                       

                      This article, intended for those new to our hobby of metalworking, explains how you can drill a hole with a hexagonal cross section. I provide all needed dimensions for a ¼” hex bit plus the math enabling you to drill any size polygon.

                       

                      If you are interested, please see

                       

                      http://rick.sparber.org/dhh.pdf

                       

                      Your comments and questions are welcome. All of us are smarter than any one of us.

                       

                      For the full index of my articles, see rick.sparber.org.

                       

                      Rick



                       

                      Attachment(s) from John

                      1 of 1 Photo(s)

                    • John
                      Actually, that s why I decided to create the program. On this version I made the following assumptions:  1.  Only one hole per corner will be drilled, using
                      Message 11 of 24 , Mar 7, 2013
                      • 1 Attachment
                      • 38 KB

                      Actually, that's why I decided to create the program.


                      On this version I made the following assumptions:

                        1.  Only one hole per corner will be drilled, using a fractional drill bit.

                        2.  The center drill will be the same size as the hex (flat-to-flat)


                      The program (as it currently stands) allows you to enter the desired hex size.  Using the up/down arrow keys, it will cycle through different hole sizes for the corners by 1/64ths.  Each time a different hole size is selected, it will recalculate the corner hole positions (X & Y), as well as recalculate the extra area removed in the corners and the area that's left behind on the flats that will still need to be removed.  When you hit a ratio of 1.0 between these two areas it would mean the extra area removed around the corners is about the same area as the bits on the flats that will need to be removed - essentially balancing the two factors.


                      As a bonus I also added an option to just show the outline created to better visualize the resulting semi-finished hole (see attached).


                      I suppose it would be possible to add the ability to maybe drill 3 holes in each corner (one large and 2 smaller ones on either side of it) to remove additional material on larger hex sizes, though then you go from drilling 7 holes to drilling 19 with 3 different sizes.  I guess that just depends on how close you need it and how much clean up you're willing to do.


                      Well, if there's interest, I can give it some more thought.  The math should be interesting.


                      -John



                      --- On Thu, 3/7/13, Rick Sparber <rgsparber@...> wrote:

                      From: Rick Sparber <rgsparber@...>
                      Subject: RE: [mill_drill] new article: Drilling a Hexagonal Hole
                      To: mill_drill@yahoogroups.com
                      Date: Thursday, March 7, 2013, 3:30 AM

                       

                      John,

                       

                      This is a good start but there is more to it. If the flat to flat distance is ¼”, then using 1/16” holes plus a ¼” center hole is good enough. But as you go to larger flat to flat distances, more small holes are needed to minimize error.

                       

                      The challenge is to calculate the diameter and location of these small holes. They will not all be 1/16”.

                       

                      Rick

                       

                      From: mill_drill@yahoogroups.com [mailto:mill_drill@yahoogroups.com] On Behalf Of John
                      Sent: Thursday, March 07, 2013 3:32 AM
                      To: mill_drill@yahoogroups.com
                      Subject: RE: [mill_drill] new article: Drilling a Hexagonal Hole [1 Attachment]

                       

                      [Attachment(s) from John included below]


                      So instead of doing real work for the past day or so, I went ahead and wrote a program to calculate and visualize the drilled hex holes based on fractional drill sizes (screenshot is attached).  I'd be more than happy to share it, though I wrote it in Python and I'm not sure if that's a deal killer for the folks here.  Mac and Linux come with Python pre-installed, and I believe I can make a stand alone EXE file for windows if desired.  Worst case I can possibly even port it into Javascript so that it can be run in a web browser.

                       

                      Anyway, I'm just trying to figure out the best way to get it into the hands of anyone that wants it.  What does everyone think?

                       

                      -John

                       


                      --- On Wed, 3/6/13, Rick Sparber <rgsparber@...> wrote:


                      From: Rick Sparber <rgsparber@...>
                      Subject: RE: [mill_drill] new article: Drilling a Hexagonal Hole
                      To: mill_drill@yahoogroups.com
                      Date: Wednesday, March 6, 2013, 6:42 AM

                       

                      John,

                       

                      Thanks for catching the error. It is now fixed plus I made the equations look a little better:

                       

                      http://rick.sparber.org/dhh.pdf

                       

                      The figures are right, only the equations were wrong.

                       

                      Rick

                       

                      From: mill_drill@yahoogroups.com [mailto:mill_drill@yahoogroups.com] On Behalf Of John
                      Sent: Tuesday, March 05, 2013 4:58 PM
                      To: mill_drill@yahoogroups.com
                      Subject: Re: [mill_drill] new article: Drilling a Hexagonal Hole

                       



                      Hey Rick, I just started going through the theory section in your paper - should the initial calculation for the hypotenuse (center to hex corner) be: 

                        1/8 / cos(30)

                      instead of:

                        1/8 x cos(30)

                       

                      -John


                      --- On Sat, 3/2/13, Rick Sparber <rgsparber@...> wrote:


                      From: Rick Sparber <rgsparber@...>
                      Subject: Re: [mill_drill] new article: Drilling a Hexagonal Hole
                      To: "mill_drill@yahoogroups.com" <mill_drill@yahoogroups.com>
                      Date: Saturday, March 2, 2013, 8:27 PM

                       

                      John,


                      That would be very impressive.

                      Rick


                      On Mar 2, 2013, at 9:26 PM, John <jennasys@...> wrote:

                      If I get some time, I'll try and write up a little program to calculate drill sizes to get the best fit/require the least amount of cleanup.

                      John


                      --- On Sat, 3/2/13, Rick Sparber <rgsparber@...> wrote:


                      From: Rick Sparber <rgsparber@...>
                      Subject: RE: [mill_drill] new article: Drilling a Hexagonal Hole
                      To: mill_drill@yahoogroups.com
                      Date: Saturday, March 2, 2013, 6:15 PM

                       

                      John,

                       

                      I was going to write up the general case as an article but then realized there is no general case. You just have to pick drill sizes that take out the most material.

                       

                      Rick

                       

                      From: mill_drill@yahoogroups.com [mailto:mill_drill@yahoogroups.com] On Behalf Of John
                      Sent: Thursday, February 28, 2013 11:52 PM
                      To: mill_drill@yahoogroups.com
                      Subject: Re: [mill_drill] new article: Drilling a Hexagonal Hole

                       

                       

                      Hey Rick,

                      I don't have the mating part in front of me, but IIRC it was about a 7/16" hex.  It just needed to be a slip fit, so I'm not too worried about tolerances.  I was thinking I'd go a little bigger on the holes for the corners and use a small file to make the flats a little "flatter" after the center drill operation.  

                      -John

                       


                      --- On Sun, 2/24/13, Rick Sparber <rgsparber@...> wrote:


                      From: Rick Sparber <rgsparber@...>
                      Subject: Re: [mill_drill] new article: Drilling a Hexagonal Hole
                      To: "mill_drill@yahoogroups.com" <mill_drill@yahoogroups.com>
                      Date: Sunday, February 24, 2013, 3:57 AM

                       

                      John,

                       

                      Glad to be of service.  What size hex do you plan to drill?

                       

                      Rick


                      On Feb 24, 2013, at 2:57 AM, John <jennasys@...> wrote:

                      Awesome.  I have a project where I need to make a single hex hole and this will work beautifully.  I had already planned on using a similar technique, but this spells out exactly what I need to do.  Thanks for posting it!

                      -John

                       


                      --- On Tue, 2/19/13, Rick Sparber <rgsparber@...> wrote:


                      From: Rick Sparber <rgsparber@...>
                      Subject: [mill_drill] new article: Drilling a Hexagonal Hole
                      To: valleymetal@yahoogroups.com, mill_drill@yahoogroups.com, smithy-machines@yahoogroups.com, 3_in_1_Lathe_Mill_Drill@yahoogroups.com
                      Date: Tuesday, February 19, 2013, 9:22 AM

                       

                      This article, intended for those new to our hobby of metalworking, explains how you can drill a hole with a hexagonal cross section. I provide all needed dimensions for a ¼” hex bit plus the math enabling you to drill any size polygon.

                       

                      If you are interested, please see

                       

                      http://rick.sparber.org/dhh.pdf

                       

                      Your comments and questions are welcome. All of us are smarter than any one of us.

                       

                      For the full index of my articles, see rick.sparber.org.

                       

                      Rick



                       

                      Attachment(s) from John

                      1 of 1 Photo(s)

                    • Rick Sparber
                      John, I found the math daunting. For example, set the flat to flat distance at ½” and drill 1/16” holes at each point. Then drill the center ½” hole.
                      Message 12 of 24 , Mar 7, 2013
                      • 0 Attachment

                        John,

                         

                        I found the math daunting. For example, set the flat to flat distance at ½” and drill 1/16” holes at each point. Then drill the center ½” hole. You will see that the excess metal to be removed is large. By eye I can pick drill sizes and hole placement to get this excess as small as I like. But doing with a program is tricky. Of course, if you drill multiple small holes, you want to keep a web of around 0.01” between holes so the drill does not break through. The large central hole doesn’t care about the smaller holes both because it is so much larger and because the smaller holes will be equally distributed around the center so no net lateral force is present.

                         

                        Best of luck!

                         

                        Rick

                         

                         

                         

                        From: mill_drill@yahoogroups.com [mailto:mill_drill@yahoogroups.com] On Behalf Of John
                        Sent: Thursday, March 07, 2013 5:55 AM
                        To: mill_drill@yahoogroups.com
                        Subject: RE: [mill_drill] new article: Drilling a Hexagonal Hole [1 Attachment]

                         

                        [Attachment(s) from John included below]


                        Actually, that's why I decided to create the program.

                         

                        On this version I made the following assumptions:

                          1.  Only one hole per corner will be drilled, using a fractional drill bit.

                          2.  The center drill will be the same size as the hex (flat-to-flat)

                         

                        The program (as it currently stands) allows you to enter the desired hex size.  Using the up/down arrow keys, it will cycle through different hole sizes for the corners by 1/64ths.  Each time a different hole size is selected, it will recalculate the corner hole positions (X & Y), as well as recalculate the extra area removed in the corners and the area that's left behind on the flats that will still need to be removed.  When you hit a ratio of 1.0 between these two areas it would mean the extra area removed around the corners is about the same area as the bits on the flats that will need to be removed - essentially balancing the two factors.

                         

                        As a bonus I also added an option to just show the outline created to better visualize the resulting semi-finished hole (see attached).

                         

                        I suppose it would be possible to add the ability to maybe drill 3 holes in each corner (one large and 2 smaller ones on either side of it) to remove additional material on larger hex sizes, though then you go from drilling 7 holes to drilling 19 with 3 different sizes.  I guess that just depends on how close you need it and how much clean up you're willing to do.

                         

                        Well, if there's interest, I can give it some more thought.  The math should be interesting.

                         

                        -John

                         


                        --- On Thu, 3/7/13, Rick Sparber <rgsparber@...> wrote:


                        From: Rick Sparber <rgsparber@...>
                        Subject: RE: [mill_drill] new article: Drilling a Hexagonal Hole
                        To: mill_drill@yahoogroups.com
                        Date: Thursday, March 7, 2013, 3:30 AM

                         

                        John,

                         

                        This is a good start but there is more to it. If the flat to flat distance is ¼”, then using 1/16” holes plus a ¼” center hole is good enough. But as you go to larger flat to flat distances, more small holes are needed to minimize error.

                         

                        The challenge is to calculate the diameter and location of these small holes. They will not all be 1/16”.

                         

                        Rick

                         

                        From: mill_drill@yahoogroups.com [mailto:mill_drill@yahoogroups.com] On Behalf Of John
                        Sent: Thursday, March 07, 2013 3:32 AM
                        To: mill_drill@yahoogroups.com
                        Subject: RE: [mill_drill] new article: Drilling a Hexagonal Hole [1 Attachment]

                         

                        [Attachment(s) from John included below]

                        So instead of doing real work for the past day or so, I went ahead and wrote a program to calculate and visualize the drilled hex holes based on fractional drill sizes (screenshot is attached).  I'd be more than happy to share it, though I wrote it in Python and I'm not sure if that's a deal killer for the folks here.  Mac and Linux come with Python pre-installed, and I believe I can make a stand alone EXE file for windows if desired.  Worst case I can possibly even port it into Javascript so that it can be run in a web browser.

                         

                        Anyway, I'm just trying to figure out the best way to get it into the hands of anyone that wants it.  What does everyone think?

                         

                        -John

                         


                        --- On Wed, 3/6/13, Rick Sparber <rgsparber@...> wrote:


                        From: Rick Sparber <rgsparber@...>
                        Subject: RE: [mill_drill] new article: Drilling a Hexagonal Hole
                        To: mill_drill@yahoogroups.com
                        Date: Wednesday, March 6, 2013, 6:42 AM

                         

                        John,

                         

                        Thanks for catching the error. It is now fixed plus I made the equations look a little better:

                         

                        http://rick.sparber.org/dhh.pdf

                         

                        The figures are right, only the equations were wrong.

                         

                        Rick

                         

                        From: mill_drill@yahoogroups.com [mailto:mill_drill@yahoogroups.com] On Behalf Of John
                        Sent: Tuesday, March 05, 2013 4:58 PM
                        To: mill_drill@yahoogroups.com
                        Subject: Re: [mill_drill] new article: Drilling a Hexagonal Hole

                         

                         

                        Hey Rick, I just started going through the theory section in your paper - should the initial calculation for the hypotenuse (center to hex corner) be: 

                          1/8 / cos(30)

                        instead of:

                          1/8 x cos(30)

                         

                        -John


                        --- On Sat, 3/2/13, Rick Sparber <rgsparber@...> wrote:


                        From: Rick Sparber <rgsparber@...>
                        Subject: Re: [mill_drill] new article: Drilling a Hexagonal Hole
                        To: "mill_drill@yahoogroups.com" <mill_drill@yahoogroups.com>
                        Date: Saturday, March 2, 2013, 8:27 PM

                         

                        John,


                        That would be very impressive.

                        Rick


                        On Mar 2, 2013, at 9:26 PM, John <jennasys@...> wrote:

                        If I get some time, I'll try and write up a little program to calculate drill sizes to get the best fit/require the least amount of cleanup.

                        John


                        --- On Sat, 3/2/13, Rick Sparber <rgsparber@...> wrote:


                        From: Rick Sparber <rgsparber@...>
                        Subject: RE: [mill_drill] new article: Drilling a Hexagonal Hole
                        To: mill_drill@yahoogroups.com
                        Date: Saturday, March 2, 2013, 6:15 PM

                         

                        John,

                         

                        I was going to write up the general case as an article but then realized there is no general case. You just have to pick drill sizes that take out the most material.

                         

                        Rick

                         

                        From: mill_drill@yahoogroups.com [mailto:mill_drill@yahoogroups.com] On Behalf Of John
                        Sent: Thursday, February 28, 2013 11:52 PM
                        To: mill_drill@yahoogroups.com
                        Subject: Re: [mill_drill] new article: Drilling a Hexagonal Hole

                         

                         

                        Hey Rick,

                        I don't have the mating part in front of me, but IIRC it was about a 7/16" hex.  It just needed to be a slip fit, so I'm not too worried about tolerances.  I was thinking I'd go a little bigger on the holes for the corners and use a small file to make the flats a little "flatter" after the center drill operation.  

                        -John

                         


                        --- On Sun, 2/24/13, Rick Sparber <rgsparber@...> wrote:


                        From: Rick Sparber <rgsparber@...>
                        Subject: Re: [mill_drill] new article: Drilling a Hexagonal Hole
                        To: "mill_drill@yahoogroups.com" <mill_drill@yahoogroups.com>
                        Date: Sunday, February 24, 2013, 3:57 AM

                         

                        John,

                         

                        Glad to be of service.  What size hex do you plan to drill?

                         

                        Rick


                        On Feb 24, 2013, at 2:57 AM, John <jennasys@...> wrote:

                        Awesome.  I have a project where I need to make a single hex hole and this will work beautifully.  I had already planned on using a similar technique, but this spells out exactly what I need to do.  Thanks for posting it!

                        -John

                         


                        --- On Tue, 2/19/13, Rick Sparber <rgsparber@...> wrote:


                        From: Rick Sparber <rgsparber@...>
                        Subject: [mill_drill] new article: Drilling a Hexagonal Hole
                        To: valleymetal@yahoogroups.com, mill_drill@yahoogroups.com, smithy-machines@yahoogroups.com, 3_in_1_Lathe_Mill_Drill@yahoogroups.com
                        Date: Tuesday, February 19, 2013, 9:22 AM

                         

                        This article, intended for those new to our hobby of metalworking, explains how you can drill a hole with a hexagonal cross section. I provide all needed dimensions for a ¼” hex bit plus the math enabling you to drill any size polygon.

                         

                        If you are interested, please see

                         

                        http://rick.sparber.org/dhh.pdf

                         

                        Your comments and questions are welcome. All of us are smarter than any one of us.

                         

                        For the full index of my articles, see rick.sparber.org.

                         

                        Rick

                         

                        Attachment(s) from John

                        1 of 1 Photo(s)

                         

                        Attachment(s) from John

                        1 of 1 Photo(s)

                      • John
                        Rick, your eye seems to be pretty accurate as the 1/16 hole for the 1/4 hex looks to be about right based on the theory as well.  You also make a good point
                        Message 13 of 24 , Mar 7, 2013
                        • 0 Attachment

                          Rick, your eye seems to be pretty accurate as the 1/16" hole for the 1/4" hex looks to be about right based on the theory as well.  You also make a good point about keeping a wall between the smaller holes.  That should further help to complicate the math  ;-)


                          -John


                          --- On Thu, 3/7/13, Rick Sparber <rgsparber@...> wrote:

                          From: Rick Sparber <rgsparber@...>
                          Subject: RE: [mill_drill] new article: Drilling a Hexagonal Hole
                          To: mill_drill@yahoogroups.com
                          Date: Thursday, March 7, 2013, 5:04 AM

                           

                          John,

                           

                          I found the math daunting. For example, set the flat to flat distance at ½” and drill 1/16” holes at each point. Then drill the center ½” hole. You will see that the excess metal to be removed is large. By eye I can pick drill sizes and hole placement to get this excess as small as I like. But doing with a program is tricky. Of course, if you drill multiple small holes, you want to keep a web of around 0.01” between holes so the drill does not break through. The large central hole doesn’t care about the smaller holes both because it is so much larger and because the smaller holes will be equally distributed around the center so no net lateral force is present.

                           

                          Best of luck!

                           

                          Rick

                           

                        • Rick Sparber
                          John, You give me too much credit. I chose 1/16” because that was the smallest drill in my fractional drill set and I had spares. I tried to use my CAD
                          Message 14 of 24 , Mar 7, 2013
                          • 0 Attachment

                            John,

                             

                            You give me too much credit. I chose 1/16” because that was the smallest drill in my fractional drill set and I had spares.

                             

                            I tried to use my CAD program to help me see the general case for any size polygon but it quickly got very complicated. Clearly a 1/16” hole at each point is a good start. But beyond that, it gets very tricky.

                             

                            Rick

                             

                            From: mill_drill@yahoogroups.com [mailto:mill_drill@yahoogroups.com] On Behalf Of John
                            Sent: Thursday, March 07, 2013 3:46 PM
                            To: mill_drill@yahoogroups.com
                            Subject: RE: [mill_drill] new article: Drilling a Hexagonal Hole

                             




                            Rick, your eye seems to be pretty accurate as the 1/16" hole for the 1/4" hex looks to be about right based on the theory as well.  You also make a good point about keeping a wall between the smaller holes.  That should further help to complicate the math  ;-)

                             

                            -John


                            --- On Thu, 3/7/13, Rick Sparber <rgsparber@...> wrote:


                            From: Rick Sparber <rgsparber@...>
                            Subject: RE: [mill_drill] new article: Drilling a Hexagonal Hole
                            To: mill_drill@yahoogroups.com
                            Date: Thursday, March 7, 2013, 5:04 AM

                             

                            John,

                             

                            I found the math daunting. For example, set the flat to flat distance at ½” and drill 1/16” holes at each point. Then drill the center ½” hole. You will see that the excess metal to be removed is large. By eye I can pick drill sizes and hole placement to get this excess as small as I like. But doing with a program is tricky. Of course, if you drill multiple small holes, you want to keep a web of around 0.01” between holes so the drill does not break through. The large central hole doesn’t care about the smaller holes both because it is so much larger and because the smaller holes will be equally distributed around the center so no net lateral force is present.

                             

                            Best of luck!

                             

                            Rick

                             




                          Your message has been successfully submitted and would be delivered to recipients shortly.