Altos 5-5AD Restoration
- Altos 5-5AD board repair
With tutoring from Bob Grieb, I learned how to better troubleshoot the motherboard. I can again see the self test boot screen, referred to earlier in this thread.
Here is what we did (Bob feel free to add/correct):
Through careful observation we determined that something was wrong with the communications between the terminal and the RS232 port. With the terminal plugged in, powered on the computer appeared to stall early in the boot process. With the terminal unplugged the computer appeared to go farther (drive would spin, hard drive would light). No characters to the display. Hmmm...
1. clean all sockets and re-seat all chips
2. check chip connections (with power off) using Ohm setting in Fluke meter. By probing a pin connection under the board and at the pin itself one can verify that there are no bad solder joints. My fluke has a beeper to signify a connection, but it's so sensitive that you really need to let the ohm readout to make sure proper voltages were coming through. We also experimented with a sheet of tin foil pressed to the bottom of the board, and used it as a proxy for ohm probes, with limited success.
3. Locate the RS232 driver chips. These chips are near the RS232 ports, and will end in 1488 (send) 1489 (receive). To verify that they're getting the proper voltage, probe pin 7 and pin 1 = -12v and pins 7 and 14 should = +12v
4. Took a look at the cable that connects the terminal with the computer. It's a straight-through. The cable should plug into the "modem" port of the Wyse terminal (not Aux)
5. Using Oscilloscope to test RS232 output (1488)
-ground clip to computer
-probe to pin 3 of rs232
-oscilloscope reports = -5V (OK)
Check oscilloscope on pin 2 of the RS2232 receiver chip (MC1489P) - found it to be bad, not receiving the signal. Replaced the chip.
6. For the TTL chips, you're looking for V=~5 (4.95/5.05 OK) *in general* there are exceptions and you should check your schematics. We did not have schematics so we had to guess. Probe the corner pins to check the voltage while the system is on.
7. Disk drive not responding: Found that the TTL chip in position D10 (a 74LS32) was bad by measuring pin 12. Going 14 ohms to ground. Replaced chip.
8. Discovered that the C2 jumper in slot 3, if pulled, will turn off autoboot to hard drive. By inserting a disk that does not boot (but is formatted for an Altos system) causes system to prompt hard drive or disk boot.
MP/M v2.14 Boot Disk
I was able to make an MP/M boot disk v 2.14. Thanks Dave Dunfield and his ImageDisk!
I was able to boot by floppy to both MP/M and CP/M, and through these regain access to the hard drive without replacing it (drive C) as I originally thought would be necessary. My guess is that when the system originally farted out, it chewed up a little of the file table making it loose it's ability to read track 0. I should be able to clean it up and boot without disk soon.
NOTE: If anyone in this group would like to join a restoration project please contact me, there are plenty of interesting systems that need analysis and restoration at InfoAge.
- Thanks Bill - always helpful to have "real world" fixit stories.
RS232 drivers are always suspect in machines of this vintage since
they are easily damaged if terminals/modems etc. are dis/mis-
They are also susceptible to electrostatic damage since they are
exposed to the outside world through serial cabling. One of my early
tech jobs as a grad student was maintaining a long serial line that
joined two buildings on campus.
After every thunderstorm, I could be almost certain that at least one
of these chips would be "blown" - often completely out of it's
socket - by induced spikes due to lighting. Terminal and computer
ends were protected by opto-isolators but the intermediate drivers
were always at risk. The problem was eventually solved by installing
fiber, but that was a "real" solution that took a bit more resources
than just stringing cable along convenient fire escapes.
--- In firstname.lastname@example.org, "B. Degnan" <billdeg@...>
> Altos 5-5AD board repair
> With tutoring from Bob Grieb, I learned how to better troubleshoot
> motherboard. I can again see the self test boot screen, referred toearlier
> in this thread.with the
> Here is what we did (Bob feel free to add/correct):
> Through careful observation we determined that something was wrong
> communications between the terminal and the RS232 port. With theterminal
> plugged in, powered on the computer appeared to stall early in theboot
> process. With the terminal unplugged the computer appeared to gofarther
> (drive would spin, hard drive would light). No characters to thedisplay.