Loading ...
Sorry, an error occurred while loading the content.

Re: I am definitely going to have to start a SOL restoration blog...

Expand Messages
  • corey986
    I should also mention my Sol-20 is a rev D motherboard.
    Message 1 of 13 , Jan 23, 2013
    • 0 Attachment
      I should also mention my Sol-20 is a rev D motherboard.

      --- In midatlanticretro@yahoogroups.com, corey986 wrote:
      >
      > So the unhacking continues....
      >
      > It looks the resistor at R14 is missing, it's a 1.5k
      > and there is a 1.5k resistor attached to a via near u47 that appears to be hanging in mid air (there isn't a silk screen so I assume its a hack unless it was used to pull a signal down/up as per a fix that is broken)
      >
      > Also it appears someone tied the serial port RTS signal to a 5v trace.
      >
      > I haven't removed the board yet from the machine, so there might be more underneath. I just need to make more room for parts on my bench as I remove them (i.e. wood sides and stuff) so they don't get damaged. Since this is a long term project I can 't just use my soldering table as I will be starting my Scelbi soon...
      >
      > From a power supply perspective the power supply puts out about 4.7 volts on the 5v when not plugged into the motherboard, but 3.7 volts when plugged in, so something is drawing it down. I removed and reseated all the chips and I just ordered a large sheet of antistatic foam so I can pull all the chips and perform the check out procedure from the manual for the video, then processor. Hopefully I can find it that way.
      >
      > It would help if at some point I can play with someone else's Sol to see what I should see when there is no personality module or Ram and then what it looks like when I start to plug them in. Also it would be helpful to see if my personality module even works, it's a mm5204 kind so I can't easily reprogram it or test it. I guess I could throw Solos on my 8k bytesaver and use it for now at the same address the personality module should be at, but I don't know if that will mess me up.
      >
      > Someone on the Altair forum is planning an mm5204 programmer so I may have to buy one if I can't get a 2708 personality module and I'm not paying $100 to that guy on ebay, it's overpriced and the card is missing a chunk (I guess someone's dog got hungry)
      >
      > Cheers,
      > Corey
      >
    • David Gesswein
      ... Not knowing anything about what type of supply this is... Since its low unloaded you may want to test it with a load resistor of the expected draw to see
      Message 2 of 13 , Jan 23, 2013
      • 0 Attachment
        On Wed, Jan 23, 2013 at 10:35:57PM -0000, corey986 wrote:
        > >From a power supply perspective the power supply puts out about 4.7 volts
        > on the 5v when not plugged into the motherboard, but 3.7 volts when plugged
        > in, so something is drawing it down.
        ...
        > so I can pull all the chips and perform the check out procedure
        >
        Not knowing anything about what type of supply this is...
        Since its low unloaded you may want to test it with a load resistor of
        the expected draw to see if the power supply is bad and its not a loading
        problem.
      • corey986
        Good point. It s a linear type supply. I can hook one up tomorrow I have one I use for testing switching supplies. Thanks, Corey
        Message 3 of 13 , Jan 23, 2013
        • 0 Attachment
          Good point. It's a linear type supply.

          I can hook one up tomorrow I have one I use for testing switching supplies.

          Thanks,
          Corey

          --- In midatlanticretro@yahoogroups.com, David Gesswein wrote:
          >
          > On Wed, Jan 23, 2013 at 10:35:57PM -0000, corey986 wrote:
          > > >From a power supply perspective the power supply puts out about 4.7 volts
          > > on the 5v when not plugged into the motherboard, but 3.7 volts when plugged
          > > in, so something is drawing it down.
          > ...
          > > so I can pull all the chips and perform the check out procedure
          > >
          > Not knowing anything about what type of supply this is...
          > Since its low unloaded you may want to test it with a load resistor of
          > the expected draw to see if the power supply is bad and its not a loading
          > problem.
          >
        • B Degnan
          ... From: midatlanticretro@yahoogroups.com [mailto:midatlanticretro@yahoogroups.com] On Behalf Of David Gesswein Sent: Wednesday, January 23, 2013 6:36 PM To:
          Message 4 of 13 , Jan 23, 2013
          • 0 Attachment
            -----Original Message-----
            From: midatlanticretro@yahoogroups.com
            [mailto:midatlanticretro@yahoogroups.com] On Behalf Of David Gesswein
            Sent: Wednesday, January 23, 2013 6:36 PM
            To: midatlanticretro@yahoogroups.com
            Subject: Re: [midatlanticretro] I am definitely going to have to start a SOL
            restoration blog...

            On Wed, Jan 23, 2013 at 10:35:57PM -0000, corey986 wrote:
            > >From a power supply perspective the power supply puts out about 4.7
            > >volts
            > on the 5v when not plugged into the motherboard, but 3.7 volts when
            > plugged in, so something is drawing it down.
            ...
            > so I can pull all the chips and perform the check out procedure
            >
            Not knowing anything about what type of supply this is...
            Since its low unloaded you may want to test it with a load resistor of the
            expected draw to see if the power supply is bad and its not a loading
            problem.

            ---

            Both Herb's working and my partially-working SOLs have ~4.75 volts on the
            motherboard rather than 5V. We tested thoroughly, it seems to be "the way
            it was". Given Herb's system works, fyi.

            Also, most people chipped off the last two pins of the edge connector of the
            personality module. This is normal.
            http://www.vintagecomputer.net/processor_tech/sol-20/sol-20_SOLOS-connectors
            -cut.jpg

            Bill
          • joshbensadon
            ... Is the voltage regulator getting very hot when plugged in (at 3.7V) ? If so, then you might be right. Otherwise, 4.7V no load is an unusual voltage for a
            Message 5 of 13 , Jan 23, 2013
            • 0 Attachment
              --- In midatlanticretro@yahoogroups.com, David Gesswein wrote:
              >
              > On Wed, Jan 23, 2013 at 10:35:57PM -0000, corey986 wrote:
              > > >From a power supply perspective the power supply puts out about 4.7 volts
              > > on the 5v when not plugged into the motherboard, but 3.7 volts when plugged
              > > in, so something is drawing it down.
              > ...
              > > so I can pull all the chips and perform the check out procedure
              > >
              > Not knowing anything about what type of supply this is...
              > Since its low unloaded you may want to test it with a load resistor of
              > the expected draw to see if the power supply is bad and its not a loading
              > problem.

              Is the voltage regulator getting very hot when plugged in (at 3.7V) ?
              If so, then you might be right. Otherwise, 4.7V no load is an unusual voltage for a standard 5V regulator. Does it use a standard regulator or is it like a LM723/2N3055 design? If it's a standard regulator, then the chip might have failed OR it could be the input filter cap (too much ripple on the input pin) or the output decoupling capacitor could be bad (check for oscillation on output).
            • corey986
              Wow I still can t get over how clean that system is from your pics. How did you clean the board and actually the whole system what well? Thanks, Corey
              Message 6 of 13 , Jan 23, 2013
              • 0 Attachment
                Wow I still can't get over how clean that system is from your pics. How did you clean the board and actually the whole system what well?

                Thanks,
                Corey

                http://www.vintagecomputer.net/processor_tech/sol-20/


                --- In midatlanticretro@yahoogroups.com, "B Degnan" wrote:
                >
                >
                >
                > -----Original Message-----
                > From: midatlanticretro@yahoogroups.com
                > [mailto:midatlanticretro@yahoogroups.com] On Behalf Of David Gesswein
                > Sent: Wednesday, January 23, 2013 6:36 PM
                > To: midatlanticretro@yahoogroups.com
                > Subject: Re: [midatlanticretro] I am definitely going to have to start a SOL
                > restoration blog...
                >
                > On Wed, Jan 23, 2013 at 10:35:57PM -0000, corey986 wrote:
                > > >From a power supply perspective the power supply puts out about 4.7
                > > >volts
                > > on the 5v when not plugged into the motherboard, but 3.7 volts when
                > > plugged in, so something is drawing it down.
                > ...
                > > so I can pull all the chips and perform the check out procedure
                > >
                > Not knowing anything about what type of supply this is...
                > Since its low unloaded you may want to test it with a load resistor of the
                > expected draw to see if the power supply is bad and its not a loading
                > problem.
                >
                > ---
                >
                > Both Herb's working and my partially-working SOLs have ~4.75 volts on the
                > motherboard rather than 5V. We tested thoroughly, it seems to be "the way
                > it was". Given Herb's system works, fyi.
                >
                > Also, most people chipped off the last two pins of the edge connector of the
                > personality module. This is normal.
                > http://www.vintagecomputer.net/processor_tech/sol-20/sol-20_SOLOS-connectors
                > -cut.jpg
                >
                > Bill
                >
              • B Degnan
                Thanks. I clean everything before I work on it. This SOL was in nice shape when I got it ... From: midatlanticretro@yahoogroups.com
                Message 7 of 13 , Jan 23, 2013
                • 0 Attachment
                  Thanks. I clean everything before I work on it. This SOL was in nice shape
                  when I got it

                  -----Original Message-----
                  From: midatlanticretro@yahoogroups.com
                  [mailto:midatlanticretro@yahoogroups.com] On Behalf Of corey986
                  Sent: Wednesday, January 23, 2013 10:11 PM
                  To: midatlanticretro@yahoogroups.com
                  Subject: [midatlanticretro] Re: I am definitely going to have to start a SOL
                  restoration blog...

                  Wow I still can't get over how clean that system is from your pics. How did
                  you clean the board and actually the whole system what well?

                  Thanks,
                  Corey

                  http://www.vintagecomputer.net/processor_tech/sol-20/


                  --- In midatlanticretro@yahoogroups.com, "B Degnan" wrote:
                  >
                  >
                  >
                  > -----Original Message-----
                  > From: midatlanticretro@yahoogroups.com
                  > [mailto:midatlanticretro@yahoogroups.com] On Behalf Of David Gesswein
                  > Sent: Wednesday, January 23, 2013 6:36 PM
                  > To: midatlanticretro@yahoogroups.com
                  > Subject: Re: [midatlanticretro] I am definitely going to have to start
                  > a SOL restoration blog...
                  >
                  > On Wed, Jan 23, 2013 at 10:35:57PM -0000, corey986 wrote:
                  > > >From a power supply perspective the power supply puts out about 4.7
                  > > >volts
                  > > on the 5v when not plugged into the motherboard, but 3.7 volts when
                  > > plugged in, so something is drawing it down.
                  > ...
                  > > so I can pull all the chips and perform the check out procedure
                  > >
                  > Not knowing anything about what type of supply this is...
                  > Since its low unloaded you may want to test it with a load resistor of
                  > the expected draw to see if the power supply is bad and its not a
                  > loading problem.
                  >
                  > ---
                  >
                  > Both Herb's working and my partially-working SOLs have ~4.75 volts on
                  > the motherboard rather than 5V. We tested thoroughly, it seems to be
                  > "the way it was". Given Herb's system works, fyi.
                  >
                  > Also, most people chipped off the last two pins of the edge connector
                  > of the personality module. This is normal.
                  > http://www.vintagecomputer.net/processor_tech/sol-20/sol-20_SOLOS-conn
                  > ectors
                  > -cut.jpg
                  >
                  > Bill
                  >



                  ------------------------------------

                  Yahoo! Groups Links
                • Systems Glitch
                  On Wed, 23 Jan 2013 22:35:57 -0000 ... Do you need a SOLOS mask ROM? I ve got one that works. I don t own a SOL-20 so it s unlikely to ever do me good. Thanks,
                  Message 8 of 13 , Jan 24, 2013
                  • 0 Attachment
                    On Wed, 23 Jan 2013 22:35:57 -0000
                    > Someone on the Altair forum is planning an mm5204 programmer so I may have to buy one if I can't get a 2708 personality module and I'm not paying $100 to that guy on ebay, it's overpriced and the card is missing a chunk (I guess someone's dog got hungry)

                    Do you need a SOLOS mask ROM? I've got one that works. I don't own a SOL-20 so it's unlikely to ever do me good.

                    Thanks,
                    Jonathan
                  • corey986
                    Is it in a personality module PCB or is it just an eprom? Thanks, Corey
                    Message 9 of 13 , Jan 24, 2013
                    • 0 Attachment
                      Is it in a personality module PCB or is it just an eprom?
                      Thanks,
                      Corey

                      --- In midatlanticretro@yahoogroups.com, Systems Glitch wrote:
                      >
                      > On Wed, 23 Jan 2013 22:35:57 -0000
                      > > Someone on the Altair forum is planning an mm5204 programmer so I may have to buy one if I can't get a 2708 personality module and I'm not paying $100 to that guy on ebay, it's overpriced and the card is missing a chunk (I guess someone's dog got hungry)
                      >
                      > Do you need a SOLOS mask ROM? I've got one that works. I don't own a SOL-20 so it's unlikely to ever do me good.
                      >
                      > Thanks,
                      > Jonathan
                      >
                    • Systems Glitch
                      ... Just the ROM. It s a mask ROM, not a PROM/EPROM. Thanks, Jonathan
                      Message 10 of 13 , Jan 24, 2013
                      • 0 Attachment
                        > Is it in a personality module PCB or is it just an eprom?

                        Just the ROM. It's a mask ROM, not a PROM/EPROM.

                        Thanks,
                        Jonathan
                      • Christian Liendo
                        Corey.. I have a blog and I haven t had time to update it.  if you want I can add you as a writer and you can add articles about the SOL restoration.
                        Message 11 of 13 , Jan 25, 2013
                        • 0 Attachment
                          Corey..
                          I have a blog and I haven't had time to update it. 
                          if you want I can add you as a writer and you can add articles about the SOL restoration.

                        • corey986
                          Thanks, but I have a website also. I never set the blog stuff up. Maybe this will force me to update it more often. Thanks anyway, Cheers, Corey
                          Message 12 of 13 , Jan 25, 2013
                          • 0 Attachment
                            Thanks, but I have a website also. I never set the blog stuff up. Maybe this will force me to update it more often.

                            Thanks anyway,
                            Cheers,
                            Corey

                            --- In midatlanticretro@yahoogroups.com, Christian Liendo wrote:
                            >
                            > Corey..
                            > I have a blog and I haven't had time to update it. 
                            > if you want I can add you as a writer and you can add articles about the SOL restoration.
                            >
                          Your message has been successfully submitted and would be delivered to recipients shortly.