Loading ...
Sorry, an error occurred while loading the content.

Re: [midatlanticretro] ray borrill and the data domain

Expand Messages
  • Evan Koblentz
    Thanks Andy. I only met him one time at the west-coast VCF, and I remember how much you personally assisted him. Wish I could ve met him when he was younger
    Message 1 of 48 , May 2, 2011
    View Source
    • 0 Attachment
      Thanks Andy. I only met him one time at the west-coast VCF, and I
      remember how much you personally assisted him. Wish I could've met him
      when he was younger and in better health. He was big supporter of what
      we all do.



      On 05/03/2011 01:36 AM, Andrew Molloy wrote:
      > I put together a small tribute site to Ray Borrill and his Data Domain
      > store. Ray was a VCFer and sold his Apple-1 at VCF 4.0 in 2000 on the
      > west coast. He had tons of interesting stories and opened one of the
      > early retail computer stores in the US back in 1976. Worked with Willy
      > Higinbotham, Bob Spinrad, Mike Swaine and Ted Nelson, among others.
      >
      > http://www.landsnail.com/thedatadomain/
      >
      > He was going to attend VCF East a few years back but had to back out
      > for health reasons.
      >
      > Andy
      >
      >
      > ------------------------------------
      >
      > Yahoo! Groups Links
      >
      >
      >
      >
    • Bill Sudbrink
      I have a Dremel, but I tend to make a mess with it. From: midatlanticretro@yahoogroups.com [mailto:midatlanticretro@yahoogroups.com] On Behalf Of Dan Roganti
      Message 48 of 48 , Jun 24, 2011
      View Source
      • 0 Attachment

        I have a Dremel, but I tend to make a mess with it.

         

        From: midatlanticretro@yahoogroups.com [mailto:midatlanticretro@yahoogroups.com] On Behalf Of Dan Roganti
        Sent: Friday, June 24, 2011 12:06 AM
        To: midatlanticretro@yahoogroups.com
        Subject: Re: [midatlanticretro] Dazzler

         




        On Thu, Jun 23, 2011 at 10:29 PM, Richard Cini <rich.cini@...> wrote:

        Bill --

            How did you machine the hole for the joystick and the pot adjustment slides? The joystick opening is about 1.5” in diameter and the adjustment slides are something like only 4mm wide. I’m figuring a nibbler and maybe a Dremel tool but I thought I’d ask before I started hacking at it.

            For the switch holes I purchased a 1/2” hole punch so I’ll get some nice clean holes with that.

            Thanks!

         



        While I haven't built a replica JS-1 yet, I have only my original JS-1, I use my dremel for many projects such as this. And with the right cutting wheel you can get the job done. They have cutting wheels which are thicker, I have 1/8". This would help in cutting a slot for the adjustment trimmers. You might have to improvise on the thickness of the slot if the cutting wheel doesn't match the trimmer knob by cutting slots incrementally till it's the right width. And use the radius of the cutting wheel to square off each end of the slot so it doesn't have that tapered look. You might need the flex shaft extension to cut the slot for the X trimmer since the distance from the edge can be longer than the dremel shaft.

        As for the joystick hole, don't they have a hole punch big enough for that ?
        That would be the quickest way out.

        =Dan






        No virus found in this message.
        Checked by AVG - www.avg.com
        Version: 10.0.1388 / Virus Database: 1513/3724 - Release Date: 06/24/11

      Your message has been successfully submitted and would be delivered to recipients shortly.