Loading ...
Sorry, an error occurred while loading the content.

Messages List

25321

Re: Newbie advice with Alice

Thanks all, No Brazilian rosewood, probably no abalone either, but very nice flamed Koa in the next build. And already one convinced customer!
timoteus_pj
Feb 6
#25321
 
25320

Re: Newbie advice with Alice

Janne, Your guitars look and sound great! I used to do a lot of guitar making in younger years. After graduating engineering school I had to decide between
LESLIE WATTS
Feb 6
#25320
 
25319

Re: Newbie advice with Alice

Sounds great! And feel free to blog about the Alice. -Scott ... -- ... And you'll visualize not taking any chances But meet them halfway with love, peace, and
Scott Helmke
Feb 6
#25319
 
25318

Re: Newbie advice with Alice

Very Nice! I am trying to record my kids Cello ensemble in the next few weeks. I will post to the group also. Jules On Sat, Feb 6, 2016 at 5:21 AM,
Jules Ryckebusch
Feb 6
#25318
 
25317

Re: Newbie advice with Alice

Here is one more NY cover clip from my home studio. Guitar captured with a 16,5mm capsule stereo pair and vocals with 25mm capsule Alice. Somehow these mics
timoteus_pj
Feb 6
#25317
 
25316

Re: Question about source and drain resistors on FET for a Schoeps c

You want voltage across the source and drain resistors to be 1/4th of the supply voltage and the voltage across the FET (Vds) to be 1/2 the supply voltage. By
Homero_Leal
Feb 3
#25316
 
25315

Re: Question about source and drain resistors on FET for a Schoeps c

... It is all the same. You want voltage across the source and drain resistors to be 1/4th of the supply voltage and the voltage across the FET (Vds) to be 1/2
Jerry Lee Marcel
Feb 3
#25315
 
25314

Re: Question about source and drain resistors on FET for a Schoeps c

Thank you Jules, Jerry and Ricardo! I got Scott's Wurcer articles from Linear Audio, and he also recommends not to use trimpots,if the mics are going to be in
Homero_Leal
Feb 3
#25314
 
25313

Re: Question about source and drain resistors on FET for a Schoeps c

As Jerry says, both will work, one with more trouble than the other. My preference for 3 different resistors is cos I am prejudiced against presets ..
ricardo_lee
Feb 2
#25313
 
25312

Re: Question about source and drain resistors on FET for a Schoeps c

The 1st solution has two advantages: it is less bulky and is not subject to tampering or accidental misadjustment. It is also cheaper in components but much
Jerry Lee Marcel
Feb 2
#25312
 
25311

Re: Question about source and drain resistors on FET for a Schoeps c

That should work just fine. Jules On Tue, Feb 2, 2016 at 1:49 PM, homero_leal@... [micbuilders] < ... That should work just fine.  Jules On Tue, Feb 2,
Jules Ryckebusch
Feb 2
#25311
 
25310

Question about source and drain resistors on FET for a Schoeps circu

This question may be mainly for Ricardo, but you guys please feel free! Ok, suppose I followed the FETBias.doc procedure, for a Schoeps Phase Splitter, and I
Homero_Leal
Feb 2
#25310
 
25309

Re: PCBs for Alice/Schoeps mics

David, that's my website, thanks for the mention. The Schoeps PCBs are probably my most popular item. Regards, Robert
gonz0id
Feb 2
#25309
 
25308

PCBs for Alice/Schoeps mics

I came across this website, and remembering that there has been a lot of discussion about building the Alice/Schoeps type circuit, I though it might be of
David Pickett
Feb 2
#25308
 
25307

Re: Need help to put one mic back in operation (Nagra JBR?)

Tried it with white connected to shield (and ground) and red connected to the tip of the connector (input) - and it works! Tested with Sony UX533 and some old
Zoran Petrovic
Feb 2
#25307
 
View First Topic Go to View Last Topic
Loading 1 - 15 of total 25,321 messages