Loading ...
Sorry, an error occurred while loading the content.

Topics List

EvaNut Update

(13)
... Only the CNC'ers with deep pockets use the ball screws. ... No. Only true CNC uses ball screws, anything less is a glorified power feed. John S.
stevenson_engineers
13
posts
4:36 PM

USB Smoothstepper and Mach4

(24)
Sorry. As you are listed as moderator with Greg on the warp9 forum, I though you were in the know ;) Thanks any way. Gaston On 15-07-03 15:17 PM, 'Jeffrey
Gaston Gagnon
24
posts
Jul 3

Motor Tuning screen won't come up

(10)
For those following the above thread the solution for me was so simple I could not see it until this morning. When I copied the file into my cnc computer after
me91967
10
posts
Jul 3

3D printing with Mach3

(27)
Arturo, This is very timely as my buddy and I are looking at converting a couple of CNC machines to 3D printers. Could you please elaborate on a complete setup
metalman7290
27
posts
Jul 1
Steve Blackmore
8
posts
Jun 28

Too good to be true 4 axes at same time?

(26)
Hi Everyone, I read just about every message thread posted on the mach group. I learned long ago that wisdom comes from multiple source's. Reading Chris's
Kevin Impson
26
posts
Jun 28

Thermal Management with your Stepper Motor

(16)
I don’t know so I am going through the process of elimination now. It is a new system I just built and it is all over again deja- vue 5 years ago. I am more
Chris
16
posts
Jun 24

Fun with logging - mach4 edition...

(22)
... Art, I think you just insulted yourself. Carter had less of a clue how to be a good president than just about any of them. Jeff Birt Soigeneris.com From:
Jeffrey Birt
22
posts
Jun 23

External E-Stop is requested?.

(12)
Didn't mean to confuse you, the values are not all that critical, .1uf is preferred, I just used what was available. Steve From: "qconvers@aol.com
Stephen Muscato
12
posts
Jun 18

Is there a way to increase Step Pulse width up above the 5 limit?

(8)
Chris, Thanks for the reply It turned out that the step pulse width was just another blind alley I was going down. The issue was lack of a ground plane. I
campgems
8
posts
Jun 17

Home switch movemet after homing

(6)
Yes ! On 17/06/2015 17:41, 'Jeffrey Birt' birt_j@soigeneris.com ... -- -hanermo (cnc designs)
Hannu Venermo
6
posts
Jun 17

MPG increments

(11)
Thanks Peter, will do, Have a great day, Chuck On Fri, Jun 12, 2015 at 12:48 AM, Peter groups@homanndesigns.com
Chuck K
11
posts
Jun 12

Rasberry Pi2 CNC?

(7)
On 10/06/15 22:36, Garry Foster garry.foster1@gmail.com [mach1mach2cnc] ... And the Toad4 board is powered by a PIC18F4550 and can generate pulses faster than
Lester Caine
7
posts
Jun 10

What do others do in this case?

(16)
This is my last post on the issue of repeat ability on a round post mill RF-30 using laser. Yeah my set up guy had same problem. - Snug the clamp bolts at same
Wolgamott M
16
posts
Jun 6

speeds and feeds

(18)
On Fri, Jun 5, 2015 at 2:14 PM, 'Rick - yahoo' rgsparber.ya@gmail.com ... Ja - - - you forgot all about your cutter. What is it? (lots of grades of every kind
o1bigtenor
18
posts
Jun 5
View First Topic Go to View Last Topic
Loading 1 - 15 of total 15 topics