Loading ...
Sorry, an error occurred while loading the content.

106918Re: [mach1mach2cnc] Re: Spindle Setup with VFD

Expand Messages
  • gcode fi (hanermo)
    Apr 1, 2009
    • 0 Attachment
      Ports n pins/Spindle setup
      check - x - "use spindle motor output"
      check - x - "step/dir spindle"

      Ports n pins/Motor outputs
      At the bottom, for spindle, check the right step/ dir pins for your setup



      Noel Anthony wrote:
      >
      > For me the MACH setup. From what I gather the 0-10 is created somehow by
      > step/direction with the Spindle Motor Output. i.e assign two pins there.
      > What pins do you choose and where do you take them. Have a separate power
      > supply for 0-10 output.
      >
      > Any clues appreciated
      >
      > Kind Regards
      >
      > Noel Anthony
      >
      > Director
      >
      > wild gravity
      >
      > www.wildgravity.com.au <http://www.wildgravity.com.au/
      > <http://www.wildgravity.com.au/>>
      >
      > From: mach1mach2cnc@yahoogroups.com
      > <mailto:mach1mach2cnc%40yahoogroups.com>
      > [mailto:mach1mach2cnc@yahoogroups.com
      > <mailto:mach1mach2cnc%40yahoogroups.com>]
      > On Behalf Of gcode fi (hanermo)
      > Sent: Wednesday, 1 April 2009 5:25 PM
      > To: mach1mach2cnc@yahoogroups.com <mailto:mach1mach2cnc%40yahoogroups.com>
      > Subject: Re: [mach1mach2cnc] Re: Spindle Setup with VFD
      >
      > Sorry ! - Did not remember about the an/out (As I use a C25).
      >
      > I have a multifunction board as well, on another lathe, and on that the
      > analog out was just like wiring to a kbic speed controller, just like
      > the c6, just like the vfd.
      > Use a separate power supply for the analog out unless things have
      > changed !
      >
      > What is your difficulty ?
      > In wiring, or mach setup, or exactly where ... if you let me know where
      > you are, I can maybe go look at mine.
      >
      > wildgrav wrote:
      > >
      > > The CNC4PC C23 Board which I have has a 0-10 out. assigned to pin 14.
      > > I cannot figure how step/dir (2 Pins) relates to that??
      > >
      > > --- In mach1mach2cnc@yahoogroups.com
      > <mailto:mach1mach2cnc%40yahoogroups.com>
      > <mailto:mach1mach2cnc%40yahoogroups.com>
      > > <mailto:mach1mach2cnc%40yahoogroups.com>, "gcode fi (hanermo)"
      > > <yahoog@...> wrote:
      > > >
      > > > You need an analog out board, like the c6 from cnc4pc.
      > > > It takes the step/dir and converts to 0-10v.
      > > > I have some, they work fine.
      > > >
      > > > wildgrav wrote:
      > > > >
      > > > >
      > > > > Hi All
      > > > >
      > > > > Could someone please explain how you get 0-10 using step/dir in
      > > > > Ports/Pins. Motor Outputs / Spindle. Where do the two pins go after
      > > > > that. The VFD has 0-10 input and a common so how does step/Dir fit
      > > with
      > > > > that.
      > > > >
      > > > > Ports/Pins, Spindle Setup allows you to choose a pin for the
      > relay and
      > > > > the Step Direction for Motor control. Is there a flow chart for
      > > dummies?
      > > > > Using SS and a C23.
      > > > >
      > > > > Regards
      > > > >
      > > > > Noel
      > > > >
      > > > >
      > > >
      > >
      > >
      > >
      >
      > [Non-text portions of this message have been removed]
      >
      >
    • Show all 11 messages in this topic