Loading ...
Sorry, an error occurred while loading the content.

Messages List

1687

Re: Setup file for KPC-3 Dan, things seem to be going from bad-to-worse here. You asked the simplest question, but our complex and varied replies would confuse me, and I've been doing

zl4ax
Feb 4
#1687
 

Messages List

1686

Re: Setup file for KPC-3 DAN WHEN I RESTORE THE KPC-3 TO DEFAULT WITH THE CMD “RESTORE D,” I RELOAD IT WITH THIS DEFAULT SETTINGS; SEE BELOW ;Parameter list for KPC3 ; HOTKEY F12 ;

COLBY I YORK JR
Feb 4
#1686
 

Messages List

1685

Re: Setup file for KPC-3 HI AGAIN DAN I NEED TO CLEAR UP WHAT I DO TO RESET MY KPC-3 BACK TO FACTORY SETTINGS, FIRST – I ENTER THE CMD “RESTORE D,” THEN I WAIT UNTIL IT RESETS

COLBY I YORK JR
Feb 4
#1685
 

Messages List

1684

Re: Setup file for KPC-3 Sorry, I still have a lot of trouble with this message board since Yahoo changed all the format. I used to just click on the guy's part-email-address at the

zl4ax
Feb 3
#1684
 

Messages List

1683

Re: Setup file for KPC-3 Dan, if it's really a text file that you have, open it with Notepad and try sending a few of the commands one at a time to the TNC. I'm assuming that you can

dave_mue11er
Feb 3
#1683
 

Messages List

1682

Re: Setup file for KPC-3 Ok, will give it a try. 73's Dan

dmlgnnv
Feb 3
#1682
 

Messages List

1681

Re: Setup file for KPC-3 We seem to be causing more confusion than helping you, because of all our different replies. Yes, you have the right program already. If you were able to

zl4ax
Feb 3
#1681
 

Messages List

1680

Re: Setup file for KPC-3 I have a text file but it seems not to work, do I need to send it with Hyper-Terminal 73's Dan

dmlgnnv
Feb 3
#1680
 

Messages List

1679

Re: Setup file for KPC-3 Colby, Just to be clear, your file appears to be the output of the "DISP" command. A file of commands to send TO the TNC would vary somewhat from that format.

John Minger
Feb 3
#1679
 

Messages List

1678

Re: Setup file for KPC-3 HI DAN I AM SENDING YOU A COPY OF MY KPC-3 SET UP PARAMETERS, HOPE THIS HELPS YOU OUT COLBY 73 KI4MPY KANTRONICS PACKET COMMUNICATOR III VERSION 8.2 (C)

COLBY I YORK JR
Feb 3
#1678
 

Messages List

1677

Re: Setup file for KPC-3 Outpost has the ability to send a file saved in the program. It sends the TNC commands before PTT-ing the radio. Don va7dgp On Tue, Feb 3, 2015 at 10:13 AM,

Don Poaps
Feb 3
#1677
 

Messages List

1676

Re: Setup file for KPC-3 The KPC3 is programmed with text commands, usually with a terminal emulator software (like Hyperterm, Putty or others) on a PC. The only way to have a "setup

dave_mue11er
Feb 3
#1676
 

Messages List

1675

Setup file for KPC-3 How do you configure a setup file to set the parameters for KPC-3 I am having problems doing that. 73 Dan

dmlgnnv
Feb 3
#1675
 

Messages List

1674

Re: Kam+ No Serial Data It was the op amp that drives the serial port, LMC6034 (U26?). Dave AA3EE

dave_mue11er
Jan 22
#1674
 

Messages List

1673

Re: Kam+ No Serial Data Measure voltage at the input and output of the 7805. The input is what voltage you are feeding into the KAM. The output should be close to 5VDC. Make sure the

kevin asato
Jan 3
#1673
 
View First Topic Go to View Last Topic
Loading 1 - 15 of total 1,687 messages