Loading ...
Sorry, an error occurred while loading the content.

Re: Node 3833 Embedded Audio a bit low

Expand Messages
  • Matthew Sybrant
    All reports I m getting are that the audio I m sending to you (other nodes) is very good/clear regards kb0jwr node 3833 ... sending to ... is by ...
    Message 1 of 6 , Jan 21, 2009
    • 0 Attachment
      All reports I'm getting are that the audio I'm sending to "you" (other
      nodes) is "very good/clear"

      regards

      kb0jwr
      node 3833

      --- In irlp-embedded@yahoogroups.com, "Nate Duehr" <nate@...> wrote:
      >
      > That covers your audio you're hearing, but not the audio you're
      sending to
      > us. The only way to know the audio you're sending to us is correct,
      is by
      > following Randy's instructions.
      >
      > :-)
      >
      > Nate
      >
      > -----Original Message-----
      > From: irlp-embedded@yahoogroups.com [mailto:irlp-
      embedded@yahoogroups.com]
      > On Behalf Of Matthew Sybrant
      > Sent: Wednesday, January 21, 2009 3:25 PM
      > To: irlp-embedded@yahoogroups.com
      > Subject: [irlp-embedded] Re: Node 3833 Embedded Audio a bit low
      >
      > Thanks for all the help. I have adj the pcm and it's now the same
      > level as all local repeaters when listening to them.
      >
      > regards
      > kb0wjr
      > node 3833
      >
      > --- In irlp-embedded@yahoogroups.com, "Nate Duehr" <nate@> wrote:
      > >
      > > It's also HIGHLY recommended that you use a good procedure to set
      > audio
      > > levels to a known standard.
      > >
      > > See the right-hand side bar on Randy KC6HUR's site for three good
      > ways to do
      > > it, one "poor-man's" method, one that utilizes an SSB receiver,
      and
      > the
      > > full-blown "borrow an FM Service Monitor and do it right" version.
      > >
      > > See "Setting Audio Levels" on the right side of this page:
      > >
      > > http://irlp.kc6hur.net/
      > >
      > > People who really care about their levels will appreciate it if
      you
      > take the
      > > time to set your levels to the network's standards via one of
      these
      > methods.
      > > Anything else, so called "setting by ear" is usually close, but it
      > often
      > > gets lost that there IS a network standard in IRLP, making it far
      > more clear
      > > and usable by users than other systems, when done right.
      > >
      > > I regularly tell users of nodes that HAVEN'T done it right, that
      > their audio
      > > sounds like crap, in hopes that their node owners will someday get
      a
      > clue...
      > > It usually doesn't work, but I guess it makes me feel better that
      at
      > least I
      > > said something and TRIED to keep up the good work people started
      > years
      > > ago... (GRIN!!!)
      > >
      > > 73,
      > >
      > > Nate WY0X
      > >
      > > -----Original Message-----
      > > From: irlp-embedded@yahoogroups.com [mailto:irlp-
      > embedded@yahoogroups.com]
      > > On Behalf Of David Cameron (IRLP)
      > > Sent: Wednesday, January 21, 2009 2:46 PM
      > > To: irlp-embedded@yahoogroups.com
      > > Subject: Re: [irlp-embedded] Node 3833 Embedded Audio a bit low
      > >
      > > The details of all of the aumix sliders are covered on page 14 in
      > the
      > > embedded information document at:
      > >
      > > http://www.irlp.net/embedded/embedded_info.pdf
      > >
      > > Generally, the Vol and PCM would be used to boost the audio from
      the
      > > node to the radio. You can also try the ogain slider (if
      equipped).
      > >
      > > If this is being used as a full duplex repeater controller, be
      aware
      > > that adjusting the Vol slider will increase the audio repeat loop
      as
      > well.
      > >
      > > Dave Cameron
      > > VE7LTD
      > >
      > > Matthew Sybrant wrote:
      > > >
      > > >
      > > > I have noticed the audio level I hear when speaking with others
      is
      > > > that the audio level I hear is a bit low. I have reports that
      the
      > > > audio level on the other end (i.e. my voice) is OK.
      > > >
      > > > Using the (aumix) script, which slider is used to adjust the
      > volume of
      > > > audio I hear on my end?
      > > >
      > > > regards
      > > > kb0jwr
      > > > node 3833
      > > >
      > > >
      > >
      > > ------------------------------------
      > >
      > > Yahoo! Groups Links
      > >
      >
      >
      >
      >
      > ------------------------------------
      >
      > Yahoo! Groups Links
      >
    Your message has been successfully submitted and would be delivered to recipients shortly.