Loading ...
Sorry, an error occurred while loading the content.
 

Re: [irlp-embedded] Outputs

Expand Messages
  • David Cameron (IRLP)
    http://www.irlp.net/new-install/Ver3_Wiring.pdf They are not open collector, as they have a 100K pull-up resistor to +5V. But they are FETs that go to ground.
    Message 1 of 6 , Jun 30, 2013
      http://www.irlp.net/new-install/Ver3_Wiring.pdf

      They are not open collector, as they have a 100K pull-up resistor to +5V.

      But they are FETs that go to ground. PTT, AUX1, AUX2, and AUX3 are all
      the same.

      They can handle up to 6A per fet, but the wire that feeds the DB-9 cable
      can only handle about 500mA.

      Dave Cameron
      VE7LTD

      On 6/30/2013 12:24 PM, dsay2001 wrote:
      > How do the outputs work? Are they Open Collector type, or ...? I looked through this board, and the Embedded Node docs, but couldn't find any details. Is there some documentation that I missed?
      >
      > Thanks.
      >
      >
    • Don Sayler
      Thanks David. Being primarily a software guy, I don t understand how to use this info. I need to use the PTT/AUX1 outputs to switch an external 10V signal to
      Message 2 of 6 , Jun 30, 2013
        Thanks David.  Being primarily a software guy, I don't understand how to use this info.

        I need to use the PTT/AUX1 outputs to switch an external 10V signal to our repeater controller.  I tried using a 5V relay, where the coil was connected between the AUX3 output (measured at 4.8V) and PTT/AUX1. 

        When I turn AUX1 on, I expected the relay to energize, but it didn't.  I did make sure that the relay worked by testing it with another 4.5V source.  What is the proper way to wire this?  Do I even need the relay?  Can I use the FET to switch the 10V directly?


        On Sun, Jun 30, 2013 at 7:20 PM, David Cameron (IRLP) <dcameron@...> wrote:
         

        http://www.irlp.net/new-install/Ver3_Wiring.pdf

        They are not open collector, as they have a 100K pull-up resistor to +5V.

        But they are FETs that go to ground. PTT, AUX1, AUX2, and AUX3 are all
        the same.

        They can handle up to 6A per fet, but the wire that feeds the DB-9 cable
        can only handle about 500mA.

        Dave Cameron
        VE7LTD



        On 6/30/2013 12:24 PM, dsay2001 wrote:
        > How do the outputs work? Are they Open Collector type, or ...? I looked through this board, and the Embedded Node docs, but couldn't find any details. Is there some documentation that I missed?
        >
        > Thanks.
        >
        >


      • dsay2001
        Let s try a different question then... What is the maximum voltage that can be applied to one of the output pins?
        Message 3 of 6 , Jul 3, 2013
          Let's try a different question then...
          What is the maximum voltage that can be applied to one of the output pins?

          --- In irlp-embedded@yahoogroups.com, Don Sayler <don.sayler@...> wrote:
          >
          > Thanks David. Being primarily a software guy, I don't understand how to
          > use this info.
          >
          > I need to use the PTT/AUX1 outputs to switch an external 10V signal to our
          > repeater controller. I tried using a 5V relay, where the coil was
          > connected between the AUX3 output (measured at 4.8V) and PTT/AUX1.
          >
          > When I turn AUX1 on, I expected the relay to energize, but it didn't. I
          > did make sure that the relay worked by testing it with another 4.5V
          > source. What is the proper way to wire this? Do I even need the relay?
          > Can I use the FET to switch the 10V directly?
          >
          >
          > On Sun, Jun 30, 2013 at 7:20 PM, David Cameron (IRLP) <dcameron@...>wrote:
          >
          > > **
          > >
          > >
          > > http://www.irlp.net/new-install/Ver3_Wiring.pdf
          > >
          > > They are not open collector, as they have a 100K pull-up resistor to +5V.
          > >
          > > But they are FETs that go to ground. PTT, AUX1, AUX2, and AUX3 are all
          > > the same.
          > >
          > > They can handle up to 6A per fet, but the wire that feeds the DB-9 cable
          > > can only handle about 500mA.
          > >
          > > Dave Cameron
          > > VE7LTD
          > >
          > >
          > > On 6/30/2013 12:24 PM, dsay2001 wrote:
          > > > How do the outputs work? Are they Open Collector type, or ...? I looked
          > > through this board, and the Embedded Node docs, but couldn't find any
          > > details. Is there some documentation that I missed?
          > > >
          > > > Thanks.
          > > >
          > > >
          > >
          > >
          > >
          >
        Your message has been successfully submitted and would be delivered to recipients shortly.