Re: [Hammock Camping] Dream hammock photos and test
- OK I think I understand now?????
1) By using the two clips on the bugnet you create a "virtual" ridgeline to
suspend the net.
2) would a couple more underbody loops help keep the net tight around your
3) I like the straps, I'm gonna try them.
On 12/4/06, Chinell, David F (GE Indust, Security) <david.chinell@...>
>[Non-text portions of this message have been removed]
> I've added a series of photos of my "Dream Hammock" to my album: Bear's
> Pix. As you may recall, this is a three-layer hammock patterned after Tom
> Claytor's "Mosquito Hammock" but with no zippers.
> For these photos, I replaced the one-foot loop of cord in the casing with
> some long tubular nylon straps so I could spread the ends out flat.
> I think the photo captions explain the construction fairly well. The
> photos with the hammock hung show how the netting presses itself against the
> body of the hammock.
> I took it out to Myakka River State Park this weekend (Saturday night) for
> a test run. It worked well, but not perfectly.
> I spent a lot more time fussing with the netting than I'd have liked to.
> It tended to lay against my face from the side. If I make a V2 of the
> hammock, I might make the lifting grossgrain straps 18 inches wide and add
> loops at the ends, so I can put a stick between the end loops to spread the
> Also, If you roll over on your side, there's a risk the netting will make
> a gap immediately opposite your face. I think this is because the tension
> caused by the shock cord running underneath puts the entire edge of the
> netting under tension -- normally a good thing. But that tight edge wants to
> be below your shoulder when you're on your back for best sealing. When
> you're on your side -- it has nothing to snap around.
> But once I put on a sleeping cap and my poncho liner, the netting stayed
> away from me. Even when I rolled, there were no gaps. No bites in the
> morning. Hooray!
> Maybe I was just too sensitized to the potential problems and consequently
> fussed too much. Once I was asleep, it seemed to handle itself without my
> As it stands, the hammock is 1 lb, 4 oz. I think even lighter materials
> could be used for the body. I'll bet it could be made under a pound.
Yes, you've got it right.
I've been thinking about ways to improve the seal as well. I'm loath to add any more clips that have to be undone and redone to get in an out. It's supposed to be at least as easy as using a zipper.
However, I'm considering experimenting with two puller straps, maybe around 1/3 the way along the sides, rather than one in the middle. That might be an acceptable compromise between solid sealing and ease of entry.
[Non-text portions of this message have been removed]
- Taking a look at your dream hammock, my first thought was two puller
straps, too. Placed just as you state below.
But, the I began to wonder about this alternative: What if you used
twice the width of mosquito netting. The netting would run from halfway
underneath, around the top, and back to halfway underneath. The netting
would only be sewn to the hammock at the casings. The rest of it
would be loose. Having the ends sewn to the casing, may keep the net
wrapped around you. So, all you'd have to do is pull the net up to
climb in and out, no calisthenics to connect puller straps underneath
you. That's the theory, but I probably do not have enough real-world
experience to predict how well it will work. For all I know, the net
would wind up as a rope over your head.
If this works, it would allow you to eliminate the puller straps all
together. The biggest disadvantage I see so far is that this will
prevent you from flipping the hammock over for a net-free night (among
other uses). This might be solved with bungies and mitten-hooks (rather
like installing a JRB quilt on the wrong side) instead of sewing the
loose halves into the underside of the hammock casing.
Chinell, David F (GE Indust, Security) wrote:
> However, I'm considering experimenting with two puller straps, maybe around 1/3 the way along the sides, rather than one in the middle. That might be an acceptable compromise between solid sealing and ease of entry.