Loading ...
Sorry, an error occurred while loading the content.

Built my dream hammock

Expand Messages
  • Chinell, David F (GE Indust, Security)
    Hangers: There are no pictures, so this may be a bit wordy. Over the holidays, my Rita helped me sew together my dream hammock. It s a design I ve been
    Message 1 of 21 , Nov 27, 2006
    • 0 Attachment
      Hangers:

      There are no pictures, so this may be a bit wordy. Over the holidays, my Rita helped me sew together my dream hammock. It's a design I've been thinking about for years while I swung in other people's designs. It's a three-layer, jungle hammock type, much like the Mosquito Hammocks, but with no zippers.

      Here's how it goes. Dimensions are finished dimensions and do not include casing allowances.

      The bottom two layers are 1.1 oz ripstop nylon (not silnylon). These pieces are 4 ft. 6 in. wide, and 8 ft long. They are joined at the ends to form a casing. The casing also includes the netting layer.

      The third layer is mosquito netting. (Would have preferred no-seeum, but couldn't get it at the time.) This layer is 5 ft. wide and 8 ft. long. All three layers are folded to form the casing.

      In addition, all three layers are sewn together for 12 inches, starting at the casing. In this area, the extra width of the netting (3 inches on each side) is tucked between the bottom layers before all three layers are sewn together.

      The netting has four areas where grossgrain ribbon straps are sewn on. Two of the straps are used to hold the netting up at the ends. Two are used to pull the netting together underneath me at the center of the hammock.

      The straps that hold the netting up are 18 inches from the casing. They are about six inches long, running parallel to the casing, and in the middle of the netting. They're made by sticking a strip inside the netting, then sticking another strip with a preformed loop on the outside, then sewing them together. (Hooray for spray adhesive!) To each loop, I attached a yard of 1/8-inch shock cord with a mitten hook at either end. One mitten hook goes through the loop, the other hook will go to my ridgeline or to the tree rope.

      The straps that pull the netting together under my butt are shaped like upside-down Ts. The base of the T runs along the edge of the netting. It's about 12 inches long and centered along the length of the netting. The vertical stem is about 7 inches long, and runs perpendicular to the edge of the netting. It's doubled over to from its own loop, which extends an inch below the edge of the netting. I use another yard of 1/8-inch shock cord to form an 18-inch loop, tied through one of the strap loops, and through a mitten hook. Once I'm in the hammock, I pull the shock cord under me to the other side, and hook the mitten hook into the other loop.

      Finally, I use two feet of 5mm rope to create a one foot loop through the casing at each end. I attach a 1-1/2 inch diameter metal ring to each loop using a lark's head.

      In practice...

      I attach my tree ropes to the tree, leaving about a yard of running end. The running end goes through the metal ring on the hammock, gets adjusted, then tied off using a Hennessy hitch or slipped sheet bend.

      If there are no bugs, I put the netting side down.

      If there are bugs, I put the netting side up, attach the shock cords at the ends to my ridge line or the tree ropes. Getting in or out just involves using the hook to attach or unattach the shock cord running underneath me.

      There are areas at the head and foot where the netting may gap away from the hammock material, but once these are arranged to run below the droop of the hammock, they press firmly against the hammock sides as if by magic. The widths of the base and netting panels are, for me, optimal to ensure protection.

      I like having the bottom two layers open along their length so I can insert and adjust my insulating pads from both sides. I also like that the hammock is symmetrical -- there's no head or foot, left or right.

      There. That's it. I wouldn't mind in the least if someone with high volume manufacturing capabilities experimented with this design using even better materials and ended up offering it as an ultra-light model, so I can have the seams perfect, and can order another one whenever I want to hook somebody else on hammocking.

      Bear



      [Non-text portions of this message have been removed]
    • tim garner
      bear... i`d really like to see pictures of that hammock, w/ a few close-ups of some of the details. sounds really great. ...tim Chinell, David F (GE
      Message 2 of 21 , Nov 27, 2006
      • 0 Attachment
        bear... i`d really like to see pictures of that hammock, w/ a few close-ups of some of the details. sounds really great. ...tim

        "Chinell, David F (GE Indust, Security)" <david.chinell@...> wrote: Hangers:

        There are no pictures, so this may be a bit wordy. Over the holidays, my Rita helped me sew together my dream hammock. It's a design I've been thinking about for years while I swung in other people's designs. It's a three-layer, jungle hammock type, much like the Mosquito Hammocks, but with no zippers.

        Here's how it goes. Dimensions are finished dimensions and do not include casing allowances.

        The bottom two layers are 1.1 oz ripstop nylon (not silnylon). These pieces are 4 ft. 6 in. wide, and 8 ft long. They are joined at the ends to form a casing. The casing also includes the netting layer.

        The third layer is mosquito netting. (Would have preferred no-seeum, but couldn't get it at the time.) This layer is 5 ft. wide and 8 ft. long. All three layers are folded to form the casing.

        In addition, all three layers are sewn together for 12 inches, starting at the casing. In this area, the extra width of the netting (3 inches on each side) is tucked between the bottom layers before all three layers are sewn together.

        The netting has four areas where grossgrain ribbon straps are sewn on. Two of the straps are used to hold the netting up at the ends. Two are used to pull the netting together underneath me at the center of the hammock.

        The straps that hold the netting up are 18 inches from the casing. They are about six inches long, running parallel to the casing, and in the middle of the netting. They're made by sticking a strip inside the netting, then sticking another strip with a preformed loop on the outside, then sewing them together. (Hooray for spray adhesive!) To each loop, I attached a yard of 1/8-inch shock cord with a mitten hook at either end. One mitten hook goes through the loop, the other hook will go to my ridgeline or to the tree rope.

        The straps that pull the netting together under my butt are shaped like upside-down Ts. The base of the T runs along the edge of the netting. It's about 12 inches long and centered along the length of the netting. The vertical stem is about 7 inches long, and runs perpendicular to the edge of the netting. It's doubled over to from its own loop, which extends an inch below the edge of the netting. I use another yard of 1/8-inch shock cord to form an 18-inch loop, tied through one of the strap loops, and through a mitten hook. Once I'm in the hammock, I pull the shock cord under me to the other side, and hook the mitten hook into the other loop.

        Finally, I use two feet of 5mm rope to create a one foot loop through the casing at each end. I attach a 1-1/2 inch diameter metal ring to each loop using a lark's head.

        In practice...

        I attach my tree ropes to the tree, leaving about a yard of running end. The running end goes through the metal ring on the hammock, gets adjusted, then tied off using a Hennessy hitch or slipped sheet bend.

        If there are no bugs, I put the netting side down.

        If there are bugs, I put the netting side up, attach the shock cords at the ends to my ridge line or the tree ropes. Getting in or out just involves using the hook to attach or unattach the shock cord running underneath me.

        There are areas at the head and foot where the netting may gap away from the hammock material, but once these are arranged to run below the droop of the hammock, they press firmly against the hammock sides as if by magic. The widths of the base and netting panels are, for me, optimal to ensure protection.

        I like having the bottom two layers open along their length so I can insert and adjust my insulating pads from both sides. I also like that the hammock is symmetrical -- there's no head or foot, left or right.

        There. That's it. I wouldn't mind in the least if someone with high volume manufacturing capabilities experimented with this design using even better materials and ended up offering it as an ultra-light model, so I can have the seams perfect, and can order another one whenever I want to hook somebody else on hammocking.

        Bear


        .

        don`t leave the CREATOR out of the creation!!!


        ---------------------------------
        Cheap Talk? Check out Yahoo! Messenger's low PC-to-Phone call rates.

        [Non-text portions of this message have been removed]
      • jonas4321
        Holy Hammocks, Batman! We need PICTURES!!!
        Message 3 of 21 , Nov 28, 2006
        • 0 Attachment
          Holy Hammocks, Batman! We need PICTURES!!!
        • jdmitchtroop226
          I gotta echo the need for pics that others have made. The design sounds very cool, but frankly, I can t manage to envision this. Sounds neat. ... holidays, my
          Message 4 of 21 , Nov 28, 2006
          • 0 Attachment
            I gotta echo the need for pics that others have made. The design
            sounds very cool, but frankly, I can't manage to envision this.

            Sounds neat.

            --- In hammockcamping@yahoogroups.com, "Chinell, David F \(GE Indust,
            Security\)" <david.chinell@...> wrote:
            >
            > Hangers:
            >
            > There are no pictures, so this may be a bit wordy. Over the
            holidays, my Rita helped me sew together my dream hammock. It's a
            design I've been thinking about for years while I swung in other
            people's designs. It's a three-layer, jungle hammock type, much like
            the Mosquito Hammocks, but with no zippers.
            >
            > Here's how it goes. Dimensions are finished dimensions and do not
            include casing allowances.
            >
            > The bottom two layers are 1.1 oz ripstop nylon (not silnylon). These
            pieces are 4 ft. 6 in. wide, and 8 ft long. They are joined at the
            ends to form a casing. The casing also includes the netting layer.
            >
            > The third layer is mosquito netting. (Would have preferred no-seeum,
            but couldn't get it at the time.) This layer is 5 ft. wide and 8 ft.
            long. All three layers are folded to form the casing.
            >
            > In addition, all three layers are sewn together for 12 inches,
            starting at the casing. In this area, the extra width of the netting
            (3 inches on each side) is tucked between the bottom layers before all
            three layers are sewn together.
            >
            > The netting has four areas where grossgrain ribbon straps are sewn
            on. Two of the straps are used to hold the netting up at the ends. Two
            are used to pull the netting together underneath me at the center of
            the hammock.
            >
            > The straps that hold the netting up are 18 inches from the casing.
            They are about six inches long, running parallel to the casing, and in
            the middle of the netting. They're made by sticking a strip inside the
            netting, then sticking another strip with a preformed loop on the
            outside, then sewing them together. (Hooray for spray adhesive!) To
            each loop, I attached a yard of 1/8-inch shock cord with a mitten hook
            at either end. One mitten hook goes through the loop, the other hook
            will go to my ridgeline or to the tree rope.
            >
            > The straps that pull the netting together under my butt are shaped
            like upside-down Ts. The base of the T runs along the edge of the
            netting. It's about 12 inches long and centered along the length of
            the netting. The vertical stem is about 7 inches long, and runs
            perpendicular to the edge of the netting. It's doubled over to from
            its own loop, which extends an inch below the edge of the netting. I
            use another yard of 1/8-inch shock cord to form an 18-inch loop, tied
            through one of the strap loops, and through a mitten hook. Once I'm in
            the hammock, I pull the shock cord under me to the other side, and
            hook the mitten hook into the other loop.
            >
            > Finally, I use two feet of 5mm rope to create a one foot loop
            through the casing at each end. I attach a 1-1/2 inch diameter metal
            ring to each loop using a lark's head.
            >
            > In practice...
            >
            > I attach my tree ropes to the tree, leaving about a yard of running
            end. The running end goes through the metal ring on the hammock, gets
            adjusted, then tied off using a Hennessy hitch or slipped sheet bend.
            >
            > If there are no bugs, I put the netting side down.
            >
            > If there are bugs, I put the netting side up, attach the shock cords
            at the ends to my ridge line or the tree ropes. Getting in or out just
            involves using the hook to attach or unattach the shock cord running
            underneath me.
            >
            > There are areas at the head and foot where the netting may gap away
            from the hammock material, but once these are arranged to run below
            the droop of the hammock, they press firmly against the hammock sides
            as if by magic. The widths of the base and netting panels are, for me,
            optimal to ensure protection.
            >
            > I like having the bottom two layers open along their length so I can
            insert and adjust my insulating pads from both sides. I also like that
            the hammock is symmetrical -- there's no head or foot, left or right.
            >
            > There. That's it. I wouldn't mind in the least if someone with high
            volume manufacturing capabilities experimented with this design using
            even better materials and ended up offering it as an ultra-light
            model, so I can have the seams perfect, and can order another one
            whenever I want to hook somebody else on hammocking.
            >
            > Bear
            >
            >
            >
            > [Non-text portions of this message have been removed]
            >
          • teblum
            ... I got to third (or fourth??) the picture request. Take a close up of the ends, where you run a loop through the casing . I m looking for an alternative
            Message 5 of 21 , Nov 28, 2006
            • 0 Attachment
              --- In hammockcamping@yahoogroups.com, "jdmitchtroop226" <jdmitch@...>
              I got to third (or fourth??) the picture request.

              Take a close up of the ends, where you run a loop through the
              "casing". I'm looking for an alternative to whipping.

              If nothing else, find someone with a camera cell phone. You get them
              free with renewall these days

              TIA
              Tom





              wrote:> I gotta echo the need for pics that others have made. The design
              > sounds very cool, but frankly, I can't manage to envision this.
              >
              > Sounds neat.
              >
              > --- In hammockcamping@yahoogroups.com, "Chinell, David F \(GE Indust,
              > Security\)" <david.chinell@> wrote:
              > >
              > > Hangers:
              > >
              > > There are no pictures, so this may be a bit wordy. Over the
              > holidays, my Rita helped me sew together my dream hammock. It's a
              > design I've been thinking about for years while I swung in other
              > people's designs. It's a three-layer, jungle hammock type, much like
              > the Mosquito Hammocks, but with no zippers.
              > >
              > > Here's how it goes. Dimensions are finished dimensions and do not
              > include casing allowances.
              > >
              > > The bottom two layers are 1.1 oz ripstop nylon (not silnylon). These
              > pieces are 4 ft. 6 in. wide, and 8 ft long. They are joined at the
              > ends to form a casing. The casing also includes the netting layer.
              > >
              > > The third layer is mosquito netting. (Would have preferred no-seeum,
              > but couldn't get it at the time.) This layer is 5 ft. wide and 8 ft.
              > long. All three layers are folded to form the casing.
              > >
              > > In addition, all three layers are sewn together for 12 inches,
              > starting at the casing. In this area, the extra width of the netting
              > (3 inches on each side) is tucked between the bottom layers before all
              > three layers are sewn together.
              > >
              > > The netting has four areas where grossgrain ribbon straps are sewn
              > on. Two of the straps are used to hold the netting up at the ends. Two
              > are used to pull the netting together underneath me at the center of
              > the hammock.
              > >
              > > The straps that hold the netting up are 18 inches from the casing.
              > They are about six inches long, running parallel to the casing, and in
              > the middle of the netting. They're made by sticking a strip inside the
              > netting, then sticking another strip with a preformed loop on the
              > outside, then sewing them together. (Hooray for spray adhesive!) To
              > each loop, I attached a yard of 1/8-inch shock cord with a mitten hook
              > at either end. One mitten hook goes through the loop, the other hook
              > will go to my ridgeline or to the tree rope.
              > >
              > > The straps that pull the netting together under my butt are shaped
              > like upside-down Ts. The base of the T runs along the edge of the
              > netting. It's about 12 inches long and centered along the length of
              > the netting. The vertical stem is about 7 inches long, and runs
              > perpendicular to the edge of the netting. It's doubled over to from
              > its own loop, which extends an inch below the edge of the netting. I
              > use another yard of 1/8-inch shock cord to form an 18-inch loop, tied
              > through one of the strap loops, and through a mitten hook. Once I'm in
              > the hammock, I pull the shock cord under me to the other side, and
              > hook the mitten hook into the other loop.
              > >
              > > Finally, I use two feet of 5mm rope to create a one foot loop
              > through the casing at each end. I attach a 1-1/2 inch diameter metal
              > ring to each loop using a lark's head.
              > >
              > > In practice...
              > >
              > > I attach my tree ropes to the tree, leaving about a yard of running
              > end. The running end goes through the metal ring on the hammock, gets
              > adjusted, then tied off using a Hennessy hitch or slipped sheet bend.
              > >
              > > If there are no bugs, I put the netting side down.
              > >
              > > If there are bugs, I put the netting side up, attach the shock cords
              > at the ends to my ridge line or the tree ropes. Getting in or out just
              > involves using the hook to attach or unattach the shock cord running
              > underneath me.
              > >
              > > There are areas at the head and foot where the netting may gap away
              > from the hammock material, but once these are arranged to run below
              > the droop of the hammock, they press firmly against the hammock sides
              > as if by magic. The widths of the base and netting panels are, for me,
              > optimal to ensure protection.
              > >
              > > I like having the bottom two layers open along their length so I can
              > insert and adjust my insulating pads from both sides. I also like that
              > the hammock is symmetrical -- there's no head or foot, left or right.
              > >
              > > There. That's it. I wouldn't mind in the least if someone with high
              > volume manufacturing capabilities experimented with this design using
              > even better materials and ended up offering it as an ultra-light
              > model, so I can have the seams perfect, and can order another one
              > whenever I want to hook somebody else on hammocking.
              > >
              > > Bear
              > >
              > >
              > >
              > > [Non-text portions of this message have been removed]
              > >
              >
            • Ralph Oborn
              ... Have you tried the double sheet bend? Ralph [Non-text portions of this message have been removed]
              Message 6 of 21 , Nov 28, 2006
              • 0 Attachment
                On 11/28/06, teblum <teblum@...> wrote:
                >
                >
                > Take a close up of the ends, where you run a loop through the
                > "casing". I'm looking for an alternative to whipping.


                Have you tried the double sheet bend?

                Ralph


                [Non-text portions of this message have been removed]
              • teblum
                I have no idea what a double sheet bend is. If you mean the knot, I have no problem with whipping and hanging successfully. It doesn t come apart. I just
                Message 7 of 21 , Nov 28, 2006
                • 0 Attachment
                  I have no idea what a "double sheet bend" is. If you mean the knot, I
                  have no problem with whipping and hanging successfully. It doesn't
                  come apart.

                  I just always end up with a tight (high) spot in the middle of the
                  hammock after using it for a while. My theory is that the fabric slips
                  through the whipping. It's just an untested theory at this point.

                  Tom

                  --- In hammockcamping@yahoogroups.com, "Ralph Oborn" <Ralph.oborn@...>
                  wrote:
                  >
                  > On 11/28/06, teblum <teblum@...> wrote:
                  > >
                  > >
                  > > Take a close up of the ends, where you run a loop through the
                  > > "casing". I'm looking for an alternative to whipping.
                  >
                  >
                  > Have you tried the double sheet bend?
                  >
                  > Ralph
                  >
                  >
                  > [Non-text portions of this message have been removed]
                  >
                • mrbyer
                  double sheet bend with photo: http://www.iland.net/~jbritton/sheetbend.htm
                  Message 8 of 21 , Nov 28, 2006
                  • 0 Attachment
                    double sheet bend with photo:

                    http://www.iland.net/~jbritton/sheetbend.htm



                    --- In hammockcamping@yahoogroups.com, "teblum" <teblum@...> wrote:
                    >
                    > I have no idea what a "double sheet bend" is. If you mean the knot, I
                    > have no problem with whipping and hanging successfully. It doesn't
                    > come apart.
                    >
                    > I just always end up with a tight (high) spot in the middle of the
                    > hammock after using it for a while. My theory is that the fabric slips
                    > through the whipping. It's just an untested theory at this point.
                    >
                    > Tom
                    >
                    > --- In hammockcamping@yahoogroups.com, "Ralph Oborn" <Ralph.oborn@>
                    > wrote:
                    > >
                    > > On 11/28/06, teblum <teblum@> wrote:
                    > > >
                    > > >
                    > > > Take a close up of the ends, where you run a loop through the
                    > > > "casing". I'm looking for an alternative to whipping.
                    > >
                    > >
                    > > Have you tried the double sheet bend?
                    > >
                    > > Ralph
                    > >
                    > >
                    > > [Non-text portions of this message have been removed]
                    > >
                    >
                  • Ralph Oborn
                    before bending the hammock to tie, try pulling the sides an inch or so tighter than the middle. The double sheet bend makes experimentation easy. Ralph
                    Message 9 of 21 , Nov 28, 2006
                    • 0 Attachment
                      before bending the hammock to tie, try pulling the sides an inch or so
                      tighter than the middle. The double sheet bend makes experimentation
                      easy.

                      Ralph

                      On 11/28/06, teblum <teblum@...> wrote:
                      > I have no idea what a "double sheet bend" is. If you mean the knot, I
                      > have no problem with whipping and hanging successfully. It doesn't
                      > come apart.
                      >
                      > I just always end up with a tight (high) spot in the middle of the
                      > hammock after using it for a while. My theory is that the fabric slips
                      > through the whipping. It's just an untested theory at this point.
                      >
                      > Tom
                      >
                      > --- In hammockcamping@yahoogroups.com, "Ralph Oborn" <Ralph.oborn@...>
                      > wrote:
                      > >
                      > > On 11/28/06, teblum <teblum@...> wrote:
                      > > >
                      > > >
                      > > > Take a close up of the ends, where you run a loop through the
                      > > > "casing". I'm looking for an alternative to whipping.
                      > >
                      > >
                      > > Have you tried the double sheet bend?
                      > >
                      > > Ralph
                      > >
                      > >
                      > > [Non-text portions of this message have been removed]
                      > >
                      >
                      >
                      >
                      >
                      >
                      > Yahoo! Groups Links
                      >
                      >
                      >
                      >
                    • jonas4321
                      ... Do yourself a favor and make your double sheet bends slipped (instead of sending the end of the webbing through the second time, fold it over and put a
                      Message 10 of 21 , Nov 29, 2006
                      • 0 Attachment
                        --- In hammockcamping@yahoogroups.com, "Ralph Oborn" <Ralph.oborn@...>
                        wrote:
                        >
                        > before bending the hammock to tie, try pulling the sides an inch or so
                        > tighter than the middle. The double sheet bend makes experimentation
                        > easy.

                        Do yourself a favor and make your double sheet bends slipped (instead
                        of sending the end of the webbing through the second time, fold it
                        over and put a loop through). This will make it lots easier to untie
                        as you experiment, or if you want to wash your hammock, or dry it, or
                        (insert personal reason here). After you've spent a few nights in the
                        hammock, any knot you have tied there will be pretty snug. The slipped
                        version gives you an easier 'undo' feature (CTRL-Z for you Windows
                        geeks out there).

                        I do gotta echo the choice of a double sheet bend, it's easier to
                        untie then whipping. To me, it's also easier to feel like I can trust
                        it not to come undone, unlike whipping, which depends on my skill at
                        doing it tight enough. One nice thing about bends is that they tighten
                        up under loads.

                        Pics of the slipped double sheet bend are under Jonas4321 in the
                        Photos section. Ignore the fact that I attach a loop, you can attach
                        one end of your webbing to the hammock the same way.

                        Jonas
                      • teblum
                        -Okay, guys. I m always ready to try new stuff. Re. the double sheet bend. Is the larger line the bunched up hammock end itself? If so, I got it. Also I got
                        Message 11 of 21 , Nov 29, 2006
                        • 0 Attachment
                          -Okay, guys. I'm always ready to try new stuff.

                          Re. the double sheet bend.

                          Is the "larger line" the bunched up hammock end itself?

                          If so, I got it.

                          Also I got it re. the slipped double bend part. That's a good tip.
                          Don't need the bos'n spike near as often with that veriation.

                          Tom


                          - In hammockcamping@yahoogroups.com, "jonas4321" <jonas4321@...> wrote:
                          >
                          > --- In hammockcamping@yahoogroups.com, "Ralph Oborn" <Ralph.oborn@>
                          > wrote:
                          > >
                          > > before bending the hammock to tie, try pulling the sides an inch or so
                          > > tighter than the middle. The double sheet bend makes experimentation
                          > > easy.
                          >
                          > Do yourself a favor and make your double sheet bends slipped (instead
                          > of sending the end of the webbing through the second time, fold it
                          > over and put a loop through). This will make it lots easier to untie
                          > as you experiment, or if you want to wash your hammock, or dry it, or
                          > (insert personal reason here). After you've spent a few nights in the
                          > hammock, any knot you have tied there will be pretty snug. The slipped
                          > version gives you an easier 'undo' feature (CTRL-Z for you Windows
                          > geeks out there).
                          >
                          > I do gotta echo the choice of a double sheet bend, it's easier to
                          > untie then whipping. To me, it's also easier to feel like I can trust
                          > it not to come undone, unlike whipping, which depends on my skill at
                          > doing it tight enough. One nice thing about bends is that they tighten
                          > up under loads.
                          >
                          > Pics of the slipped double sheet bend are under Jonas4321 in the
                          > Photos section. Ignore the fact that I attach a loop, you can attach
                          > one end of your webbing to the hammock the same way.
                          >
                          > Jonas
                          >
                        • Sandy Kramer
                          ... ditto... PS Don t try it in Florida without no see um mesh!
                          Message 12 of 21 , Nov 29, 2006
                          • 0 Attachment
                            --- In hammockcamping@yahoogroups.com, "jonas4321" <jonas4321@...>
                            wrote:
                            >
                            > Holy Hammocks, Batman! We need PICTURES!!!
                            >

                            ditto...

                            PS Don't try it in Florida without no see 'um mesh!
                          • jonas4321
                            ... Yes. Just remember, the loose end of the hammock must end up on the same side of the finished bend as the bitter end (free end) of the rope or webbing.
                            Message 13 of 21 , Nov 30, 2006
                            • 0 Attachment
                              --- In hammockcamping@yahoogroups.com, "teblum" <teblum@...> wrote:
                              >
                              > -Okay, guys. I'm always ready to try new stuff.
                              >
                              > Re. the double sheet bend.
                              >
                              > Is the "larger line" the bunched up hammock end itself?

                              Yes.

                              Just remember, the "loose" end of the hammock must end up on the same
                              side of the finished bend as the bitter end (free end) of the rope or
                              webbing. They must exit the same side. If they exit opposite sides,
                              you'll have a danger of the bend slipping.

                              Sorry, that hurt my head just re-reading it.

                              A properly tied sheet bend has both free ends of the ropes on the same
                              side of the finished bend. If you imagine the hammock being one of the
                              ropes, you'll get what I mean.

                              Here's a web page that has a picture of the knot (um, bend):

                              http://www.scoutxing.com/knots/double_sheet_bend/double_sheet_bend.gif

                              Jonas
                            • Chinell, David F (GE Indust, Security)
                              Hangers: I ve added a series of photos of my Dream Hammock to my album: Bear s Pix. As you may recall, this is a three-layer hammock patterned after Tom
                              Message 14 of 21 , Dec 4, 2006
                              • 0 Attachment
                                Hangers:

                                I've added a series of photos of my "Dream Hammock" to my album: Bear's Pix. As you may recall, this is a three-layer hammock patterned after Tom Claytor's "Mosquito Hammock" but with no zippers.

                                For these photos, I replaced the one-foot loop of cord in the casing with some long tubular nylon straps so I could spread the ends out flat.

                                I think the photo captions explain the construction fairly well. The photos with the hammock hung show how the netting presses itself against the body of the hammock.

                                I took it out to Myakka River State Park this weekend (Saturday night) for a test run. It worked well, but not perfectly.

                                I spent a lot more time fussing with the netting than I'd have liked to. It tended to lay against my face from the side. If I make a V2 of the hammock, I might make the lifting grossgrain straps 18 inches wide and add loops at the ends, so I can put a stick between the end loops to spread the netting.

                                Also, If you roll over on your side, there's a risk the netting will make a gap immediately opposite your face. I think this is because the tension caused by the shock cord running underneath puts the entire edge of the netting under tension -- normally a good thing. But that tight edge wants to be below your shoulder when you're on your back for best sealing. When you're on your side -- it has nothing to snap around.

                                But once I put on a sleeping cap and my poncho liner, the netting stayed away from me. Even when I rolled, there were no gaps. No bites in the morning. Hooray!

                                Maybe I was just too sensitized to the potential problems and consequently fussed too much. Once I was asleep, it seemed to handle itself without my intervention.

                                As it stands, the hammock is 1 lb, 4 oz. I think even lighter materials could be used for the body. I'll bet it could be made under a pound.

                                Bear
                                <http://geo.yahoo.com/serv?s=97359714/grpId=8969804/grpspId=1705065843/msgId=16436/stime=1164650894/nc1=1/nc2=2/nc3=3>



                                [Non-text portions of this message have been removed]
                              • Jeff
                                Great pics, Bear...looks like an excellent project. Maybe if you sewed a small strip of elastic, maybe 3 long, right where the netting sags onto your face, it
                                Message 15 of 21 , Dec 4, 2006
                                • 0 Attachment
                                  Great pics, Bear...looks like an excellent project.

                                  Maybe if you sewed a small strip of elastic, maybe 3" long, right
                                  where the netting sags onto your face, it would tighten it up enough
                                  to keep it off your face.

                                  Also, I think you may have discussed this before but I don't remember
                                  the details. On the close-up pic of your rings attachment, is that
                                  just a cord holding the rings, then the webbing passes through it?
                                  Has that been strong enough to hold you well w/o slipping? And it's
                                  easy to undo in the morning?

                                  Jeff
                                • Chinell, David F (GE Indust, Security)
                                  Jeff: If you mean the photo titled Rings close up then what you re looking at is the stock configuration of a Travel Hammock. It s a single layer of
                                  Message 16 of 21 , Dec 4, 2006
                                  • 0 Attachment
                                    Jeff:

                                    If you mean the photo titled "Rings close up" then what you're looking at is the stock configuration of a "Travel Hammock."

                                    It's a single layer of parachute nylon with a casing. They use 7 or 8 mm prussik cord through the casing. I attached my two rings using a Lark's head hitch -- didn't even have to untie the stock loop.

                                    And yes, it holds just fine and is easy to adjust or release in the morning.

                                    Some folks can't find the right combination of webbing and rings to make it work without slipping, but I don't have that problem. (Maybe it's got something to do with my body weight?)

                                    All that happens is that the surface of the webbing gets either really compressed or hot or something that makes it a bit shiny. But that doesn't seem to impact the operation much.

                                    If you look at the "Ring and toggle" photo, that method seems even better to me. And you'll notice that topologically, the ring and toggle is the same as a common ladder buckle.

                                    I'd like to be the first to advance the theory that if we could find a sufficiently thick ladder buckle, that's all we'd need for a simple, adjustable strap system. I've tried it with a wire ladder buckle of about 1/8 inch gauge wire, but the force just bends the middle wire in. Once the webbing goes flat, it starts to slip.

                                    Bear


                                    [Non-text portions of this message have been removed]
                                  • Ralph Oborn
                                    OK I think I understand now????? 1) By using the two clips on the bugnet you create a virtual ridgeline to suspend the net. 2) would a couple more underbody
                                    Message 17 of 21 , Dec 4, 2006
                                    • 0 Attachment
                                      OK I think I understand now?????

                                      1) By using the two clips on the bugnet you create a "virtual" ridgeline to
                                      suspend the net.
                                      2) would a couple more underbody loops help keep the net tight around your
                                      shoulers?


                                      3) I like the straps, I'm gonna try them.

                                      Ralph


                                      On 12/4/06, Chinell, David F (GE Indust, Security) <david.chinell@...>
                                      wrote:
                                      >
                                      > Hangers:
                                      >
                                      > I've added a series of photos of my "Dream Hammock" to my album: Bear's
                                      > Pix. As you may recall, this is a three-layer hammock patterned after Tom
                                      > Claytor's "Mosquito Hammock" but with no zippers.
                                      >
                                      > For these photos, I replaced the one-foot loop of cord in the casing with
                                      > some long tubular nylon straps so I could spread the ends out flat.
                                      >
                                      > I think the photo captions explain the construction fairly well. The
                                      > photos with the hammock hung show how the netting presses itself against the
                                      > body of the hammock.
                                      >
                                      > I took it out to Myakka River State Park this weekend (Saturday night) for
                                      > a test run. It worked well, but not perfectly.
                                      >
                                      > I spent a lot more time fussing with the netting than I'd have liked to.
                                      > It tended to lay against my face from the side. If I make a V2 of the
                                      > hammock, I might make the lifting grossgrain straps 18 inches wide and add
                                      > loops at the ends, so I can put a stick between the end loops to spread the
                                      > netting.
                                      >
                                      > Also, If you roll over on your side, there's a risk the netting will make
                                      > a gap immediately opposite your face. I think this is because the tension
                                      > caused by the shock cord running underneath puts the entire edge of the
                                      > netting under tension -- normally a good thing. But that tight edge wants to
                                      > be below your shoulder when you're on your back for best sealing. When
                                      > you're on your side -- it has nothing to snap around.
                                      >
                                      > But once I put on a sleeping cap and my poncho liner, the netting stayed
                                      > away from me. Even when I rolled, there were no gaps. No bites in the
                                      > morning. Hooray!
                                      >
                                      > Maybe I was just too sensitized to the potential problems and consequently
                                      > fussed too much. Once I was asleep, it seemed to handle itself without my
                                      > intervention.
                                      >
                                      > As it stands, the hammock is 1 lb, 4 oz. I think even lighter materials
                                      > could be used for the body. I'll bet it could be made under a pound.
                                      >
                                      > Bear
                                      >
                                      > http://geo.yahoo.com/serv?s=97359714/grpId=8969804/grpspId=1705065843/msgId=16436/stime=1164650894/nc1=1/nc2=2/nc3=3
                                      >


                                      [Non-text portions of this message have been removed]
                                    • Chinell, David F (GE Indust, Security)
                                      Ralph: Yes, you ve got it right. I ve been thinking about ways to improve the seal as well. I m loath to add any more clips that have to be undone and redone
                                      Message 18 of 21 , Dec 5, 2006
                                      • 0 Attachment
                                        Ralph:

                                        Yes, you've got it right.

                                        I've been thinking about ways to improve the seal as well. I'm loath to add any more clips that have to be undone and redone to get in an out. It's supposed to be at least as easy as using a zipper.

                                        However, I'm considering experimenting with two puller straps, maybe around 1/3 the way along the sides, rather than one in the middle. That might be an acceptable compromise between solid sealing and ease of entry.

                                        Bear


                                        [Non-text portions of this message have been removed]
                                      • Cara Lin Bridgman
                                        Taking a look at your dream hammock, my first thought was two puller straps, too. Placed just as you state below. But, the I began to wonder about this
                                        Message 19 of 21 , Dec 6, 2006
                                        • 0 Attachment
                                          Taking a look at your dream hammock, my first thought was two puller
                                          straps, too. Placed just as you state below.

                                          But, the I began to wonder about this alternative: What if you used
                                          twice the width of mosquito netting. The netting would run from halfway
                                          underneath, around the top, and back to halfway underneath. The netting
                                          would only be sewn to the hammock at the casings. The rest of it
                                          would be loose. Having the ends sewn to the casing, may keep the net
                                          wrapped around you. So, all you'd have to do is pull the net up to
                                          climb in and out, no calisthenics to connect puller straps underneath
                                          you. That's the theory, but I probably do not have enough real-world
                                          experience to predict how well it will work. For all I know, the net
                                          would wind up as a rope over your head.

                                          If this works, it would allow you to eliminate the puller straps all
                                          together. The biggest disadvantage I see so far is that this will
                                          prevent you from flipping the hammock over for a net-free night (among
                                          other uses). This might be solved with bungies and mitten-hooks (rather
                                          like installing a JRB quilt on the wrong side) instead of sewing the
                                          loose halves into the underside of the hammock casing.

                                          CL

                                          Chinell, David F (GE Indust, Security) wrote:
                                          > However, I'm considering experimenting with two puller straps, maybe around 1/3 the way along the sides, rather than one in the middle. That might be an acceptable compromise between solid sealing and ease of entry.
                                        Your message has been successfully submitted and would be delivered to recipients shortly.