Loading ...
Sorry, an error occurred while loading the content.
 

Another good part

Expand Messages
  • afogassa
    This time with red pigment, the first part failled to come up good becouse i did not made the supports very well and it end up getting distorted, but i´ve got
    Message 1 of 4 , Feb 17, 2013
      This time with red pigment, the first part failled to come up good becouse i did not made the supports very well and it end up getting distorted, but i´ve got it right on the second try. deviation was 0.3mm at the most and about 0.2mm oversize overal,this time i had to scale it in x,y,z by 1.02 to get it right.
      next step is to get a pump to stir up the red pigment
    • afogassa
      forgot the pics link
      Message 2 of 4 , Feb 17, 2013
        forgot the pics link
        http://groups.yahoo.com/group/diy_3d_printing_and_fabrication/photos/album/27619611/pic/361404488/view?picmode=&mode=tn&order=ordinal&start=1&count=20&dir=asc


        --- In diy_3d_printing_and_fabrication@yahoogroups.com, "afogassa" <afogassa@...> wrote:
        >
        > This time with red pigment, the first part failled to come up good becouse i did not made the supports very well and it end up getting distorted, but i´ve got it right on the second try. deviation was 0.3mm at the most and about 0.2mm oversize overal,this time i had to scale it in x,y,z by 1.02 to get it right.
        > next step is to get a pump to stir up the red pigment
        >
      • Mike Polcyn
        nice... how large (small) is this part? Mike ... From: afogassa Subject: [diy_3d_printing_and_fabrication] Re: Another good part To:
        Message 3 of 4 , Feb 17, 2013
          nice... how large (small) is this part?
          Mike

          --- On Sun, 2/17/13, afogassa <afogassa@...> wrote:

          From: afogassa <afogassa@...>
          Subject: [diy_3d_printing_and_fabrication] Re: Another good part
          To: diy_3d_printing_and_fabrication@yahoogroups.com
          Date: Sunday, February 17, 2013, 6:31 AM

           

          forgot the pics link
          http://groups.yahoo.com/group/diy_3d_printing_and_fabrication/photos/album/27619611/pic/361404488/view?picmode=&mode=tn&order=ordinal&start=1&count=20&dir=asc

          --- In diy_3d_printing_and_fabrication@yahoogroups.com, "afogassa" wrote:
          >
          > This time with red pigment, the first part failled to come up good becouse i did not made the supports very well and it end up getting distorted, but i´ve got it right on the second try. deviation was 0.3mm at the most and about 0.2mm oversize overal,this time i had to scale it in x,y,z by 1.02 to get it right.
          > next step is to get a pump to stir up the red pigment
          >

        • afogassa
          It�s a small one, 44mm diameter by 22mm
          Message 4 of 4 , Feb 17, 2013
            It´s a small one, 44mm diameter by 22mm

            --- In diy_3d_printing_and_fabrication@yahoogroups.com, Mike Polcyn <lizardman2000@...> wrote:
            >
            > nice... how large (small) is this part?
            > Mike
            >
            > --- On Sun, 2/17/13, afogassa <afogassa@...> wrote:
            >
            > From: afogassa <afogassa@...>
            > Subject: [diy_3d_printing_and_fabrication] Re: Another good part
            > To: diy_3d_printing_and_fabrication@yahoogroups.com
            > Date: Sunday, February 17, 2013, 6:31 AM
            >
            >
            >
            >
            >
            >
            >
            >
            >
            >
            >
            >
            >
            >
            >
            >
            >  
            >
            >
            >
            >
            >
            >
            >
            >
            >
            > forgot the pics link
            >
            > http://groups.yahoo.com/group/diy_3d_printing_and_fabrication/photos/album/27619611/pic/361404488/view?picmode=&mode=tn&order=ordinal&start=1&count=20&dir=asc
            >
            >
            >
            > --- In diy_3d_printing_and_fabrication@yahoogroups.com, "afogassa" wrote:
            >
            > >
            >
            > > This time with red pigment, the first part failled to come up good becouse i did not made the supports very well and it end up getting distorted, but i´ve got it right on the second try. deviation was 0.3mm at the most and about 0.2mm oversize overal,this time i had to scale it in x,y,z by 1.02 to get it right.
            >
            > > next step is to get a pump to stir up the red pigment
            >
            > >
            >
          Your message has been successfully submitted and would be delivered to recipients shortly.