Loading ...
Sorry, an error occurred while loading the content.

36RE: [capri26] How Much Play is too much play?

Expand Messages
  • Leighton Westlake
    Apr 12, 2007
    • 0 Attachment

      Something to be said for tillers!

       

      Leighton D. Westlake , Jr.

      Vice-President and General Manager

      Team USA-5 division of

      The DANIS Group, llc

      10175 Flag Drive

      Palm Beach Gardens, FL 33410-4775

      TEL: 561-799-5280

      FAX: 561-799-5776

      email: leighton @...


      From: capri26@yahoogroups.com [mailto: capri26@yahoogroups.com ] On Behalf Of Tom Black
      Sent: Thursday, April 12, 2007 2:15 PM
      To: capri26@yahoogroups.com
      Subject: Re: [capri26] How Much Play is too much play?

       

      Thanks for the info Leighton. Unfortunately in my situation it is not a particularly easy job to drop the rudder. My boat has wheel steering and a diesel engine. This makes working behind the aft bulkhead a tough place to be. I think I would have to remove the steering quadrant and a couple of other things I cannot even see because of the fuel tank. This is why I was trying to gauge how much play is typical. It's potentially a bigger project than I want to tackle unless absolutely necessary.

      On 4/12/07, Leighton Westlake <leighton@thedanisgr oup.com> wrote:

      Check the bushings top and bottom.  On mine they are plastic and have lasted without problem. They may have broken and are causing excess play in the rudder.  If I had my choice I would have a bronze bushing made just because I do not trust plastic. It is easy enough to drop the rudder and inspect the bushings.

       

      Leighton D. Westlake , Jr.

      Vice-President and General Manager

      Team USA-5 division of

      The DANIS Group, llc

      10175 Flag Drive

      Palm Beach Gardens , FL 33410-4775

      TEL: 561-799-5280

      FAX: 561-799-5776

      email: leighton @thedanisgroup. com


      From: capri26@yahoogroups .com [mailto:capri26@yahoogroups .com] On Behalf Of Bob Unkel
      Sent: Monday, April 09, 2007 7:30 PM
      To: capri26@yahoogroups .com
      Subject: Re: [capri26] How Much Play is too much play?

       

      On 4/8/07 11:00 PM, "Tom Black" <uslaser@gmail. com> wrote:


       
       

      Hello All,

      While preparing for bottom paint, I noticed the rudder has some play
      front to back, may be up and down. Does anyone know what is correct
      here. Is any play too much? or is some play typical?

      Thanks,

      Tom
       Tom:
          Just how much clearance do you have or what makes you think there is a problem? These things are not precision fit assemblies.
       There is some clearance between the rudder post and the housing in the hull. The vertical clearance is determined between the tiller fitting and the top of the rudder. There should be a 'washer/shim' between the top of the rudder  and the hull. It is like a big plastic washer.
          Do you have a tiller or wheel steering? If tiller you can remove the single bolt in the tiller fitting that bolts it to the rudder shaft and the rudder will drop down. It weighs about 40-50#. I can 'rock' my rudder back and forth with the tip of the rudder probably moving at least 1". The rudder shaft housing in the hull is just fiberglass and there aren't any 'replaceable bearings' in this assembly. If you have a lot of clearance, you might be able to use a strip of UHMW tape around the shaft or in the housing to take up excess clearance.
          As for a wheel steering, I haven't had one apart so I can't comment. I believe they put the sector gear below the deck and opened up the housing. The shaft is still supported top and bottom. Getting it out will involve tearing apart the wheel steering. Perhaps one of our other members has had this apart and can share their experience with you.

      Regards,
      Bob Unkel
           
          

       

       

    • Show all 17 messages in this topic