Loading ...
Sorry, an error occurred while loading the content.

Re: [bolger] Re: MICRO TRAWLER

Expand Messages
  • nezih
    Agree with you sir. Maintenance is priority for inboard and outboard. ... From: Douglas Pollard To: bolger@yahoogroups.com Sent: Monday, November 12, 2012 7:21
    Message 1 of 42 , Nov 13, 2012
      Agree with you sir.
      Maintenance is priority for inboard and outboard.
      ----- Original Message -----
      Sent: Monday, November 12, 2012 7:21 PM
      Subject: Re: [bolger] Re: MICRO TRAWLER


      Well I don't agree in principal.  The present day inboard outboards may have problems but there is absolutely no reason why they should be less long lived than an outboard.  The leg and shafting and gears as well as bearings and seals are about the same. The engine being inboard is well protected from the weather and should last longer than one out in the salt spray and rain. If they are less dependable it is because they are flawed not due to any advantage of outboard motors over inboards. I think inboards are the reliable, the easiest to work on big alternators are easily fitted.  A good diesel is infinantly rebuildable. The small volvo in my boat is almost 40 years old. It is saltwater cooled and is still running and dependable.  I would say the difference could be that people don't pull the inboard outboars off and have the underwater seals replaced . With the outboard that is easily done, so to me that means poor maintenance rather than more trouble prone?          Doug  

      On 11/12/2012 11:51 AM, philbolger@... wrote:


      Way too heavy anyway...

      Susanne Altenburger, Phil Bolger & Friends
      ----- Original Message -----
      Sent: Monday, November 12, 2012 11:22 AM
      Subject: Re: [bolger] Re: MICRO TRAWLER


      What ever you decide DO NOT USE A STERNDRIVE INBOARD !!!!  I/O  as they are known in the

      USA  are the worst choice for saltwater. I made a poem about them :


      I O,  IO,-- it will never work you know

      It will,you think

      and then it sinks

      IO ,IO 

      Too much to go wrong. Seals ,hydraulics,electrical,linkage,gages and saltwater corrosion and electrolysis. Save your money. In my opinion ,you can't beat a 4 stroke outboard  . The smallest that will give you the performance you desire. Keep it as simple as possible. The main advantage of and outboard is there in no thru - hull fittings to worry about . Most boats sink at their docks with leaking thru - hull fittings. Capt. Rocky

      From: "nezih" <gencahm@gmail.com>
      To: bolger@yahoogroups.com
      Sent: Monday, November 12, 2012 11:03:49 AM
      Subject: Re: [bolger] Re: MICRO TRAWLER


      Agree with you and I will calculate the weight of Dieel Engine and also shaft angle.
      Maybe stern drive inboard is OK.
      ----- Original Message -----
      Sent: Sunday, November 11, 2012 9:43 PM
      Subject: [bolger] Re: MICRO TRAWLER


      Well, sir, okay. So Hawkeye seems one half meter too long. And the photo of Katie Z is irresistible!

      Further, I only suggest you watch the diesel's weight and shaft angle carefully.

      Best o' luck.

      On Nov 11, 2012, at 4:24 AM, nezih wrote:


      Dear Mr.Mark,
      Thanks for your below comments.You know why I want to build MT?Bcs it lenght is less than five metric meters.
      In my country,boat owners,more than five meters,paying taxes.MT is capable for trailer transportation easily and
      it is enough for me at he moment(for 62 years old man).It is also easy to maintain it.
      I mean,expectations after sixty is not so high!!!
      Thanks again

      True Doug, Ford FE gas truck engines had larger diameter crankshafts and cam profiles designed more for low RPM torque, compared to the equivalent car engines.
      Message 42 of 42 , Nov 16, 2012
        True Doug, Ford FE gas truck engines had larger diameter crankshafts and cam profiles designed more for low RPM torque, compared to the equivalent car engines. Some GMC truck gassers even had exhaust valve rotators and stellite valve seats, anticipating heavier engine load demands. 

        Your Isuzu may have had oil starvation issues if the oilpan capacity was not increased and the pickup lowered. I have a marinized 1956 Packard V8 with the oilpan capacity increased from 5 quarts to 4 gallons and an integral oil cooler built in. Most working boats of 25-30 feet and up have gone diesel but that may not be a practical option for the MT being discussed. 4 cycle outboards have been around for several years now and have a good track record even in small commercial fishboats that get hard use.

        From: Douglas Pollard <dougpol1@...>
        To: bolger@yahoogroups.com
        Sent: Fri, November 16, 2012 12:33:28 PM
        Subject: Re: [bolger] Re: MICRO TRAWLER


        Yes this is all true. Back in the 1960's we used to marinize v8 gasoline engines for Chesapeake Bay work boats. WE always looked for a truck engine because they had four bolt main bearings and I think maybe an extra main though I am not sure about that. Most Of the small diesel boat engine are industrial stationary engine that the manufacturer has marinized. There is not much difference between an engine running a boat and one running a water pump 24-7.   I think that the Volkswagen 4 cylinder automobile diesel engine did not hold up well.  I had a 3cylinder Izuzu diesel in a boat and it was a marinized industrial engine.  I had trouble with the #1 cylinder and again after rebuilding. I figured it was designed to set flat when running and the incline may have been a problem??   My experience with outboard engines is that they don't last long in my experience. This may be due to running wide open all the time??   I can't speak for the 4 cycle high torque engines with propellers intended for slower none plaining boats. They may be great?           Doug

        On 11/16/2012 12:29 PM, JOHN WALLIS wrote:
        Good points Susanne. Also consider that automobile engines typically only run @ about 20% of rated max HP around 80% of the time (coasting, idling at the stop light, flat terrain cruising etc). 

        On the other hand, when you consider hull drag, prop thrust and friction, marine engines are constantly going uphill towing a trailer and are designed accordingly. My recommendation is a 4 stroke outboard until you get into larger boats where a diesel inboard makes more sense. 

        From: "philbolger@..." <philbolger@...>
        To: bolger@yahoogroups.com
        Sent: Fri, November 16, 2012 4:57:13 AM
        Subject: Re: [bolger] Re: MICRO TRAWLER


        Every SUBARU engine is a flat -4 or -6 - and always water-cooled.

        Ultimately for the horsepower to get MT up on a plane no power plant will as light for the power as an outboard by the time you add up gearbox, shafting, propeller, pivoting of prop etc.

        Susanne Altenburger, PB&F
        ----- Original Message -----
        From: nezih
        Sent: Friday, November 16, 2012 3:35 AM
        Subject: Re: [bolger] Re: MICRO TRAWLER


        Any picture of the Engine,you saw in Fort Lauderdale in a Dunebuggy shop.
        Highly appreciated
        ----- Original Message -----
        Sent: Friday, November 16, 2012 4:24 AM
        Subject: Re: [bolger] Re: MICRO TRAWLER


        I read someplace that the engine designer was an airplane designer. It sure looks like and airplane engine. Back in the 1980's somebody built a water cooled aluminum block to bolt on to the crank case in place of the air cooled jugs.  They also had water cooled heads for it. I saw one of the engines in a Dunebuggy shop In Fort Lauderdale. That engine might well make a nice boat engine.  

        On 11/15/2012 09:00 PM, Mark Albanese wrote:

        Yeh, it was great to have it and the transaxle balanced atop a rolling jack. The heat is what burned the valves out. I expect in a boat one may also seem pretty loud.

        On Nov 15, 2012, at 11:49 AM, Douglas Pollard wrote:

        What the engine had going for it was it could be dropped out for rebuilding in 15 minutes.  Usually the valves were burned and new rings needed the lower end bearings and crank held up well... ...I would think it would make a far better engine for an air boat. In this case it can be standing above the boat where it can get free air circulation.  

        On 11/15/2012 12:52 PM, nezih wrote:

        Yesterday,I have been informed that boat builders here are installing old VW Beetle Engines(after marinise)
        as Inboard Engine.They are not heavy,like outbards.I think this engine eliminates the weight problem of other
        Inboard Engines
        Awaiting comments.

      Your message has been successfully submitted and would be delivered to recipients shortly.