Re: [axialflux] WG fuses Re: disconnect switch
- You need to rethink what an axial flux is, the voltages we are working with, and the application. Your "issues" do not apply.On Thu, Dec 6, 2012 at 7:57 PM, jerry freedomev <freedomev@...> wrote:Hi Steve and All,Not having a fuse or breaker between the battery and anything is illegal in every code I've seen and plain asking for trouble, fires and even explosions. Not having one on a WG is also not a good idea as it could catch on fire, electrify the tower, and burn up the wires, etc.Depending on a load to keep a WG from distruction isn't a smart way to go as too many failure points in the system that will also unload it. You need a WG that can survive an unloaded state or it won't survive in real life.Jerry DycusFrom: Steve Spence <greentrust@...>
Sent: Thursday, December 6, 2012 7:48 PM
Subject: Re: [axialflux] Re: disconnect switch
You do not want a fuse between the battery and the wind turbine.
On 12/6/2012 7:39 PM, Robert Copcutt wrote:High enough to withstand normal operation extremely reliably and not
leave your turbine unloaded. Small enough to prevent your wires catching
fire if there is a short.
On Thu, 2012-12-06 at 12:45 -0800, jon dyer wrote:
> Thank you Robert, how high is a "high rated fuze"?
> Jon Dyer
> From: Robert Copcutt <mailto:r%40copcutt.me.uk>
> To: mailto:axialflux%40yahoogroups.com
> Sent: Wednesday, December 5, 2012 8:39 AM
> Subject: Re: [axialflux] Re: disconnect switch
> On Sun, 2012-12-02 at 06:44 -0800, jon dyer wrote:
> > But if one of the diodes fails while the disconnect switch is still
> > you will have a problem.
> A high rated fuse connected very near to one of the battery terminals
> a good idea anyway.
-- Steve, KK4HFJ http://www.green-trust.org http://www.essnmag.com http://arduinotronics.blogspot.com
Director, Green Trust
Yes very true, I have it running to my battery banks. I was just trying to say I am happy with the Axial flux setup. I’m not here to put it down in any way.
Axial flux alternators are not designed for grid tie. You need a grid tie inverter.
On 12/10/2012 3:34 PM, Jeff wrote:
Don’t get me wrong but I like my turbine but it’s just been the blades, the blades did come from them and he has e-mail to help fix it right. I have had very good output from it; I am a net meter home. And try to push all I can back to the grid to where it’s the world’s largest battery, and think the setup itself is right and has all ways worked.
Hi Jeff and all,
You should consider just buying a better blade set as there are multiple ones out there like otherpower, etc. Better than chucking the whole thing and cheaper too. Hugh Piggott has free plans if you want to try your own in wood or FG. Or take the 2 good close to the same weight ones, balance them and just use a 2 blade set up. Please change subject when you do.
I got the 10’ kit with a 24VDC setup and it came with the blades and from day one I had to add a lot of weight to 1 blade to get it to balance out., First I did it the way they tell you and add weight to stop it from turning and found it still shakes everything, So I took the blades off and checked the weight of each blade, Found one was a bit longer, then did the string way by hanging it and adding weight to get it to balance level. Then put it back on and did the test again to make sure the blades stayed where you left them. And still acts like it’s out of balance, Getting ready to take it down and replace the whole turbine with another type. I have just spent way too much time it trying to get it to work right. I will say when the wind blows it makes good power, I have a output meter on it and can pin it at 50 amps. I did get my blades with my kit and know I had to do some work But I have one blade that is all most the weight of 2 blades that came in the kit.