Loading ...
Sorry, an error occurred while loading the content.

Topics List

QCTP for 10" Atlas?
(11)
Thanks, Kurt. I would like to see pictures, but this is no hurry. I have some minor need for the lathe right now, but nothing for which a QCTP would make all

Bruce .
11
posts
2:08 PM

Topics List

Hardening a spindle shaft
(32)
Nothing wrong with that.... Sounds like you have very realistic expectations, and are doing it 'cause you like to. I respect that. I do lots of things

jtiers
32
posts
8:03 PM

Topics List

Atlas 10FV In the UK - my first lathe
(30)
Ben & Jerry, I haven't taken any careful measurements but the top of the T-slot or boring slide is I think thicker than the top of the standard cross slide.

wa5cab
30
posts
Mar 2

Topics List

VFD w/ 3-phase or DC - recommendations?
(10)
Thank guys for the input. Thanks Carvel for that bit of information on the frequency range, I will look for a 120 Hz VFD. The motor is a new Lincoln Welding

stanley5819@att.net
10
posts
Feb 27

Topics List

treadmill motlr on a 10f?
(65)
Sounds right. That's what I did with the 6" I ran with a TM motor. David Hair ... From: 'Glenn N' glennsneff@gmail.com [atlas_craftsman] To:

David Hair
65
posts
Feb 26

Topics List

Re: [atlas_craftsman] New file uploaded to atlas_craftsman
(129)
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the atlas_craftsman group. File :

atlas_craftsman@yahoogroups.com
129
posts
Feb 25

Topics List

iGaging & Absolute DRO's Again
(9)
Yes you can. You just are not looking at it right... IF you have backlash, AND YOU DO....(because EVERY *leadscrew / feedscrew* machine has it, even when

jtiers
9
posts
Feb 21

Topics List

Feed Rate re set to .0021!
(12)
Robert, what block?

a8050266
12
posts
Feb 21

Topics List

How do you mount a quick change tool holder for a 10 inch lathe
(15)
I got my quick change tool post holder mounted tonight. I ended up cutting the base plate down to 1 inch by .300 so it would slide into the T slot, using a

topsaddle@att.net
15
posts
Feb 21

Topics List

Atlas Milling Attachment Replacement Jaw Blocks.
(9)
I have about a bzillion (30+ anyway) wall mount cabinets with the common about 3/4 x 2 x 5 plastic drawers. One drawer that's right behind me as I stand at

wa5cab
9
posts
Feb 15

Topics List

QCTP Holder Type 16 (116)
(8)
Robert, How about a photo of what your looking for. David Hair ... From: wa5cab@cs.com [atlas_craftsman] To: atlas_craftsman@yahoogroups.com Sent: Saturday,

David Hair
8
posts
Feb 14

Topics List

Carriage problem
(13)
I should have added... Clausing has both the wipers and the oilers (and probably the retainers but lose one, those should last forever). Robert Downs - Houston

wa5cab
13
posts
Feb 8

Topics List

Re: Milling setup for Atlas 10-inch
(12)
Thanks! I will measure later, kids schedule has me tight right now. Whit Sent from my iPhone ... Thanks! I will measure later, kids schedule has me tight right

Whitney
12
posts
Feb 7

Topics List

Milling setup for Atlas 10-inch.
(28)
OK. Thanks. So it would fit the front slot on the Atlas Double Tool Cross Slide. Although that slot is right at the front of the slide, which isn't ideal.

wa5cab
28
posts
Feb 7

Topics List

Looking for a steady rest
(24)
Oops just saw it was $13 ($3) seemed low lol On Feb 4, 2015 12:26 PM, "Kurt Bjorling kb@muziker.org [atlas_craftsman]"

Chris Anderson
24
posts
Feb 4
View First Topic Go to View Last Topic
Loading 1 - 15 of total 15 topics