Loading ...
Sorry, an error occurred while loading the content.

Topics List

Fw: new message

(3)
Jon, RobertA peddler of a diet program  GP From: "finewood@... [atlas_craftsman]" To: "Mark Spencer
christopher_matthew_andrews
3
posts
5:06 AM

My new to me Atlas has a few problems

(29)
Keith, There should be a metal plate on the motor somewhere showing how to connect the wiring. For several reasons that some of us think are still good, you
rutter.keith
29
posts
10:43 PM

Fibre Washer for Counter Shaft 9-146

(47)
Bill,   There is another kind, like a tube that just goes inside the pulley bore,and slides over the shaft, and has two hex shapes, at the outside end,hold
geoffrey_in_siam_atlas_12in_3991
47
posts
11:44 AM

Re: Differences between Atlas TH 36 and other Atlas 10" la...

(4)
I have the apron back together and I did use socket head screws. I don't want to go crazy buying things that are not necessary until I know that this is going
wa5cab
4
posts
Feb 10

Quick change gear box for my Lathe

(9)
... A quick change box does nothing for the spindle. It changes how many turns of the leadscrew per turn of the spindle. It's used in place of having to swap
rutter.keith
9
posts
Feb 10

Differences between Atlas TH 36 and other Atlas 10" lathes

(1)
I just dragged home an Atlas TH 36 in filthy condition. I am curious about parts interchangeability between this and other Atlas models. I have a manual for a
daviddazer
1
post
Feb 10

Re: [atlas_craftsman] My new to me Atlas has a few problems

(1)
Yeah, I would say a weekend is quite aggressive. 😊 Sent from my HTC ... From: "thehairs@... [atlas_craftsman]" To:
Kurt Sierens
1
post
Feb 8

1964 Atlas/Craftsman motor support Rings

(1)
It turned out that the rubber support rings that fit on my 1964 motor are not that common. I was able to find rings that had the right OD and then grind the ID
Rick - yahoo
1
post
Feb 7

Parts for drum switches?

(5)
On 2/6/2016 11:46 PM, 'Carvel Webb' carvelw@... ... For a plastic one and a month or two on a slow boat from Asia. Not at all fitting for a lathe
Gregg Eshelman
5
posts
Feb 7

Half Nut ?

(17)
I have seen some folks who make lead screw nuts out of Delrin by boring a rod undersize, slicing it in half, then clamping it in a vice around the leadscrew.
fa_s_na_10_tic
17
posts
Feb 6

Atlas 10" saddle and cross slide $95 shipped in the USA

(1)
$95 includes shipping anywhere in the USA Includes: Saddle casting Both bearing plates Gib Gib screws Cross slide/compound rest base swivel with good tight nut
dwshelf
1
post
Feb 5

rubber moter mounts failed

(3)
The first ebay item has an OD of 2-1/4" and not 2-1/2" but otherwise is exactly what I need. I measured an ID of 1.85" but maybe some of that was wear and
Rick - yahoo
3
posts
Feb 4

Atlas 12" Lathe Partout

(2)
Hi i was wondering if you still had the compound gear with the guard?? thanks, Ed C. . .
xfy80ihv
2
posts
Feb 4

Lathe Spindle

(10)
Jim, I should have written "Atlas MOLO". Short for Atlas Manual Of Lathe Operations and Machinists Tables. Any one of the 33 Editions or 10 versions. Robert
jimbrady@bellsouth.net
10
posts
Feb 3

atlas 6" mkII clutch not working right......

(5)
hi I finally got around to looking at the clutch on the mk2.....I have been into it a couple of times and I kept noticing about 3/16 play between the pulley
hyme64
5
posts
Feb 3
View First Topic Go to View Last Topic
Loading 1 - 15 of total 16,704 topics