Loading ...
Sorry, an error occurred while loading the content.

Messages List

3941

Econo-Probe Sale

I thought this might be of interest to this group. If inappropriate, please let me know. Wildhorse Innovations is offering the Econo-Probe 3D Probe & Tool
wildhorsesoftware
May 14
#3941
 
3940

Re: Sieg Power Feed Circuit

Sorry that was a mistake, How about thi one ? 4k7 4.7k Switched Linear Potentiometer
ray.tony27
Mar 22
#3940
 
3939

Re: Sieg Power Feed Circuit

Thanks for the link but I was looking for a pot which also has an integrated on/off switch. I tried many suppliers of electronic parts (I live in Sydney, Aust)
paulj1950
Mar 22
#3939
 
3938

Re: Sieg Power Feed Circuit

Rotary Potentiometer - 4.7k Ohm, Linear - COM-09941 - SparkFun Electronics https://www.sparkfun.com/products/9941 Rotary Potentiometer - 4.7k Ohm, Linear -
ray.tony27
Mar 21
#3938
 
3937

Re: Sieg Power Feed Circuit

Thanks Sandy for the link to the Grizzly site. Unfortunately the circuit for the power feed is not shown. Regards, Paul.
paulj1950
Mar 17
#3937
 
3936

Re: Sieg Power Feed Circuit

The Grizzly G0619 is an SX-3. The Manual is on line as well as a Parts List. They have been very helpful with my SX-3. They even have most parts in stock at
sandy8228
Mar 17
#3936
 
3935

Sieg Power Feed Circuit

The switch on the Sieg power feed potentiometer on my SX3 mill has failed and the supplier where I bought the mill does not keep spares. Does anyone have a
paulj1950
Mar 16
#3935
 
3934

Re: Bruce Murray's X3 spindle mod

Thanks Sandy. That's good info. Bill
W. Smith
Mar 10
#3934
 
3933

Re: Bruce Murray's X3 spindle mod

I have a SX3 and when my bearings died, I changed the upper to a taper. I did not install the thrust bearing or spacer. Timken told me to set the bearing
sandy8228
Mar 10
#3933
 
3932

Re: Bruce Murray's X3 spindle mod

Paul I gave the wrong file name. The copy in our group's file section is named: "SIEG X3 Small Mill History.pdf" The file has several mods Bruce made to his
W. Smith
Mar 9
#3932
 
3931

Re: Bruce Murray's X3 spindle mod

Hi Bill, I have looked for the spindle modification but cannot find it. Can you point me in the right direction. Regards, Paul.
paulj1950
Mar 9
#3931
 
3930

Bruce Murray's X3 spindle mod

I'm attempting to do Bruce's mod to my X3's spindle as he documented in the X3_MODS_Bruce_Murray.pdf file. There's a copy of that file in our groups files
W. Smith
Mar 9
#3930
 
3929

Re: SX3 Spindle bearings

Thank you  for this information.Paul. From: "Hannu Venermo gcode.fi@... [X_Series_Mills]" To:
Paul James
Feb 18
#3929
 
3928

Re: SX3 Spindle bearings

It cannot be done by torque. There are too many variables that change the torque by more than 100%. Note: Too much is just 1 degree extra tightening. As soon
Hannu Venermo
Feb 18
#3928
 
3927

Re: SX3 Spindle bearings

Thanks Les,The guide shows how to assemble the spindle but does not specify the torque for pre-loading the bearings. From: "g8fub@... [X_Series_Mills]"
Paul James
Feb 17
#3927
 
View First Topic Go to View Last Topic
Loading 1 - 15 of total 3,941 messages