Loading ...
Sorry, an error occurred while loading the content.

Messages List

1434

Re: Restoring a 1972 Venture 2-24 Find a friend with a table saw for the guides. While not teak, oak would do. For the crack apply a layer of fiberglass on the underside. Leave and inch on

William Reichert
Feb 16
#1434
 

Messages List

1433

Restoring a 1972 Venture 2-24 I am restoring V224 and the companion way top sliding hatch door has been stepped on and is cracked. The teak rails are all rotten as well. Does anyone have

tharris2663
Feb 16
#1433
 

Messages List

1432

Re: Venture 24' "Project Sailboat" Boat Only - $200 (Eden, MD) I am restoring a V224 of my own. I am interested in the teak rails and hatch slide. Mine has been stepped on and is cracked pretty badly. My teak rails were

tharris2663
Feb 16
#1432
 

Messages List

1431

Re: Outboard for the venture The drilled number for mine was on starboard stringer under cockpit I think. Something interesting to add to considering which side to mount on. I've recently

Taylor
Jan 29
#1431
 

Messages List

1430

Re: Hull ID Your manufacture month is also March.  So between March (your boat) and August ( my boat) they made approximately 53 boats a month. Dwight Sent from Yahoo!

robert Harness
Jan 29
#1430
 

Messages List

1429

Re: Hull ID The E is just a letter the manufacture can use as part of the serial number. It could also be a number. The format was changed in August 1984. Your hull number

robert Harness
Jan 29
#1429
 

Messages List

1428

Re: Outboard for the venture My 73 v224 I d is on the starboard (right) side about 1 inch below the cap joint. They are also drilled into one of the stringers. Somewhere on our site it

robert Harness
Jan 29
#1428
 

Messages List

1427

Re: Outboard for the venture First question is..what motor mount are you using. Second question is which motor are you using? The trick to mounting height is to measure from the bottom of

gunnerasch4570
Jan 28
#1427
 

Messages List

1426

Re: Outboard for the venture Taylor I have a V224 and it has not had a motor on it......where is yours mounted.....port starboard of tiller.....how high off the water line....any

sipandbip
Jan 28
#1426
 

Messages List

1425

Re: Outboard for the venture Hull Number location......Its not on the stern like my V224.....like it was on My V222where else are the Id Numbers or hull numbers......Thanks Len Nortbern

sipandbip
Jan 28
#1425
 

Messages List

1424

Hull ID Does anyone know what the ‘E’ represents in my hull ID, all of the info I’ve found on the web indicates a three letter manufacture code followed by a

scottharter@rocketmail.com
Jan 28
#1424
 

Messages List

1422

Re: Venture 24' "Project Sailboat" Boat Only - $200 (Eden, MD) Take her out past the 3 mile limit. (Grin)

gunnerasch4570
Jan 20
#1422
 

Messages List

1421

Re: Venture 24' "Project Sailboat" Boat Only - $200 (Eden, MD) I always liked your idea of selling the hull for a Vikings funeral. Of course the EPA might get involved. Dwight Sent from Yahoo! Mail on Android

robert Harness
Jan 20
#1421
 

Messages List

1420

Re: Venture 24' "Project Sailboat" Boat Only - $200 (Eden, MD) 4 winches 25 each, mast 200, keel 200, rudder ?, sails 2-500. I'll take one stanchion base. Last one on starboard side. I'll donate a hazmat suit to the

fuller630
Jan 18
#1420
 

Messages List

1419

Venture 24' "Project Sailboat" Boat Only - $200 (Eden, MD) http://easternshore.craigslist.org/boa/4846431458.html http://easternshore.craigslist.org/boa/4846431458.html Venture 24' "Project Sailboat" Boat Only - $200

gunnerasch4570
Jan 18
#1419
 
View First Topic Go to View Last Topic
Loading 1 - 15 of total 1,434 messages