Loading ...
Sorry, an error occurred while loading the content.

Re: New here, saying Hi.

Expand Messages
  • crackerkorean
    The keeper pin being the locking wire? I thought once the screw was removed the gib could be moved.
    Message 1 of 26 , Jun 19, 2009
    • 0 Attachment
      The keeper pin being the locking wire? I thought once the screw was removed the gib could be moved.

      --- In SherlineCNC@yahoogroups.com, Rich Dean <toolman8@...> wrote:
      >
      > Take a small pin punch like object and reach into the other end
      > and tap the gib to knock it loose.
      > Be sure to remove the keeper pin first.
      > -=RichD=-
      >
      > crackerkorean wrote:
      > > I am hoping to take it apart this weekend. I loosened the gib screw
      >
      > but I cannot mmove the gib at all. I am wondering if this is whats making
      >
      > it o difficult to move this axis.
      >
    • Rich Dean
      What I meant to say was to be careful that the wire does comes out with the gib as sometimes it will be stuck as well. Just keep an eye on it. -=RichD=-
      Message 2 of 26 , Jun 19, 2009
      • 0 Attachment
        What I meant to say was to be careful that the wire does comes out with the
        gib as sometimes it will be stuck as well. Just keep an eye on it.
        -=RichD=-

        crackerkorean wrote:
        > The keeper pin being the locking wire? I thought once the screw was removed the gib could be moved.
        >
        > --- In SherlineCNC@yahoogroups.com, Rich Dean <toolman8@...> wrote:
        >> Take a small pin punch like object and reach into the other end
        >> and tap the gib to knock it loose.
        >> Be sure to remove the keeper pin first.
        >> -=RichD=-
        >>
        >> crackerkorean wrote:
        >>> I am hoping to take it apart this weekend. I loosened the gib screw
        >> but I cannot mmove the gib at all. I am wondering if this is whats making
        >>
        >> it o difficult to move this axis.
      • crackerkorean
        I was able to remove the cross slide and then was able to remove the gib. That seemed to be the problem. Through when i use it manualy to face anything in the
        Message 3 of 26 , Jun 20, 2009
        • 0 Attachment
          I was able to remove the cross slide and then was able to remove the gib. That seemed to be the problem. Through when i use it manualy to face anything in the chuck once the facing is finished and when retracting the tool without moving the Z axis at all it seems to run into the work piece again.

          Also when turning an OD i see regular chatter still even when using the tool manually. I am just wondering if there are some more adjustments that I might need to make. I do have to say it is behaving better though.

          --- In SherlineCNC@yahoogroups.com, Rich Dean <toolman8@...> wrote:
          >
          > What I meant to say was to be careful that the wire does comes out with the
          > gib as sometimes it will be stuck as well. Just keep an eye on it.
          > -=RichD=-
          >
          > crackerkorean wrote:
          > > The keeper pin being the locking wire? I thought once the screw was removed the gib could be moved.
          > >
          > > --- In SherlineCNC@yahoogroups.com, Rich Dean <toolman8@> wrote:
          > >> Take a small pin punch like object and reach into the other end
          > >> and tap the gib to knock it loose.
          > >> Be sure to remove the keeper pin first.
          > >> -=RichD=-
          > >>
          > >> crackerkorean wrote:
          > >>> I am hoping to take it apart this weekend. I loosened the gib screw
          > >> but I cannot mmove the gib at all. I am wondering if this is whats making
          > >>
          > >> it o difficult to move this axis.
          >
        • Rich Dean
          cracker (?) the gib should be inserted just enough to cause a little drag on the slide. Grab hold of the slide and try to twist it side to side. No movement
          Message 4 of 26 , Jun 20, 2009
          • 0 Attachment
            cracker (?)
            the gib should be inserted just enough to cause a little drag on the slide.
            Grab hold of the slide and try to twist it side to side. No movement should be
            evident.
            The slide should not wobble about as you describe as the leadscrew is turned.
            -=RichD=-

            crackerkorean wrote:
            > I was able to remove the cross slide and then was able to remove the gib. That seemed to be the problem. Through when i use it manualy to face anything in the chuck once the facing is finished and when retracting the tool without moving the Z axis at all it seems to run into the work piece again.
            >
            > Also when turning an OD i see regular chatter still even when using the tool manually. I am just wondering if there are some more adjustments that I might need to make. I do have to say it is behaving better though.
          • crackerkorean
            Cracker is fine or mike lol. I inserted the gib a little more but still getting the movement and its getting tough to move the cross slide. I was actually
            Message 5 of 26 , Jun 21, 2009
            • 0 Attachment
              Cracker is fine or mike lol.
              I inserted the gib a little more but still getting the movement and its getting tough to move the cross slide. I was actually getting movement initially when the gib was crammed in. Is it possible the cross slide is worn out? The anodizing still looked good.

              I also noticed that there is no backlash adjustment per the the sherline site. Granted its taken up in the software but could I add one?
              --- In SherlineCNC@yahoogroups.com, Rich Dean <toolman8@...> wrote:
              >
              > cracker (?)
              > the gib should be inserted just enough to cause a little drag on the slide.
              > Grab hold of the slide and try to twist it side to side. No movement should be
              > evident.
              > The slide should not wobble about as you describe as the leadscrew is turned.
              > -=RichD=-
              >
              > crackerkorean wrote:
              > > I was able to remove the cross slide and then was able to remove the gib. That seemed to be the problem. Through when i use it manualy to face anything in the chuck once the facing is finished and when retracting the tool without moving the Z axis at all it seems to run into the work piece again.
              > >
              > > Also when turning an OD i see regular chatter still even when using the tool manually. I am just wondering if there are some more adjustments that I might need to make. I do have to say it is behaving better though.
              >
            • Rich Dean
              Mike, I haven t been following this entire thread, but is this a new lathe? If the black anodizing is intact then all I can suggest is maybe the plastic
              Message 6 of 26 , Jun 21, 2009
              • 0 Attachment
                Mike,
                I haven't been following this entire thread, but is this a new lathe?
                If the black anodizing is intact then all I can suggest is maybe the plastic
                tapered gib is trashed???
                Also, I have had a case of a mill base that did not perform correctly. On close
                inspection I discovered it may have been dropped and the dovetail was bent down
                causing severe binding at one end.
                Check it out with a straight edge ( a good Starrett 6" rule or ground parallel).
                The lathe has no B/L adjust nut like the mills as the cutting load is always (!)
                in one direction.
                NOT! My next mod to my cnc'd lathe.
                -=RichD=-

                crackerkorean wrote:
                > Cracker is fine or mike lol.
                > I inserted the gib a little more but still getting the movement and its getting tough to move the cross slide. I was actually getting movement initially when the gib was crammed in. Is it possible the cross slide is worn out? The anodizing still looked good.
                >
                > I also noticed that there is no backlash adjustment per the the sherline site. Granted its taken up in the software but could I add one?
                > --- In SherlineCNC@yahoogroups.com, Rich Dean <toolman8@...> wrote:
                >> cracker (?)
                >> the gib should be inserted just enough to cause a little drag on the slide.
                >> Grab hold of the slide and try to twist it side to side. No movement should be
                >> evident.
                >> The slide should not wobble about as you describe as the leadscrew is turned.
                >> -=RichD=-
                >>
                >> crackerkorean wrote:
                >>> I was able to remove the cross slide and then was able to remove the gib. That seemed to be the problem. Through when i use it manualy to face anything in the chuck once the facing is finished and when retracting the tool without moving the Z axis at all it seems to run into the work piece again.
                >>>
                >>> Also when turning an OD i see regular chatter still even when using the tool manually. I am just wondering if there are some more adjustments that I might need to make. I do have to say it is behaving better though.
              • crackerkorean
                It isnt new, it came from a school so who knows what kind of history it has. I think I might try to tighten the gib on the saddle a little and see if that
                Message 7 of 26 , Jun 23, 2009
                • 0 Attachment
                  It isnt new, it came from a school so who knows what kind of history it has.

                  I think I might try to tighten the gib on the saddle a little and see if that helps at all.

                  Is there a way to retro fit a backlash adjustment on the cross slide since mine is lacking one?

                  Hopefully this weekend I can actually start machining things. As time goes I want to upgrade the spindle motor and steppers and change to some other software, drivers , and controllers etc.
                • crackerkorean
                  I tightened the saddle gib and I am still having issues. I put a straight edge on a piece that I faced and its cupped. The center of the piece is lower than
                  Message 8 of 26 , Jun 26, 2009
                  • 0 Attachment
                    I tightened the saddle gib and I am still having issues. I put a straight edge on a piece that I faced and its cupped. The center of the piece is lower than the edge.

                    Could it be a lead screw problem?
                  • Rich Dean
                    That would indicate the spindle head is not squarely aligned with the bed. -=RichD=-
                    Message 9 of 26 , Jun 26, 2009
                    • 0 Attachment
                      That would indicate the spindle head is not squarely aligned with the bed.
                      -=RichD=-

                      crackerkorean wrote:
                      > I tightened the saddle gib and I am still having issues. I put a straight edge on a piece that I faced and its cupped. The center of the piece is lower than the edge.
                      >
                      > Could it be a lead screw problem?
                    • Andy Wander
                      As I understand it, this is part of the spec on a lathe.The point being, you will never make it perfect(spindle at a perfect 90 degrees to the cross-slide
                      Message 10 of 26 , Jun 26, 2009
                      • 0 Attachment
                        As I understand it, this is part of the spec on a lathe.

                        The point being, you will never make it perfect(spindle at a perfect 90 degrees to the cross-slide travel). If you face a piece and it is slightly dished, it will sit flat on another piece, but if it is domed instead, it will rock.

                        It should be just a slight amount, though.

                        ______________________________________
                        Andy Wander
                        ]
                        -----Original Message-----
                        From: SherlineCNC@yahoogroups.com [mailto:SherlineCNC@yahoogroups.com] On Behalf Of Rich Dean
                        Sent: Friday, June 26, 2009 3:12 PM
                        To: SherlineCNC@yahoogroups.com
                        Subject: [SherlineCNC] Re: New here, saying Hi.

                        That would indicate the spindle head is not squarely aligned with the bed.
                        -=RichD=-

                        crackerkorean wrote:
                        > I tightened the saddle gib and I am still having issues. I put a straight edge on a piece that I faced and its cupped. The center of the piece is lower than the edge.
                        >
                        > Could it be a lead screw problem?


                        ------------------------------------

                        Yahoo! Groups Links



                        This communication including any attachments, are intended
                        for the exclusive use of the addressee(s) and contains
                        confidential or copyrighted materials. Duplication,
                        distribution or reproduction is strictly prohibited by law
                        without written permission of Verrex
                      Your message has been successfully submitted and would be delivered to recipients shortly.