Loading ...
Sorry, an error occurred while loading the content.

Topics List

Sabre 28 - Bulkhead damaged

(8)
I agree with Dan, there is no need to re-design the chainplate location. Once the bulkhead is repaired, and then the chainplates are properly caulked and
David Popken
8
posts
8:38 PM

Best tape for multi-day exterior bright work?

(13)
I looked at the tape this weekend, in case anyone is interested. It's "Scotch Outdoor Painters Clean Removal Tape"
Harry K
13
posts
7:13 PM

Cruising Boats of the Caribbean

(10)
Three reasons, unrelated. First, when the trades are blowing, genoa alone is completely sufficient. Another is that when we're just hanging out rather than
Jim Starkey
10
posts
2:15 PM

Oil Pressure Switch for Alarm

(11)
Marinebeam offers the 1142 LED equivalent in either "warm white" (3000 K color temp) or in "cool white" (6500 K). The outfit recommended by Harry offers only a
Bennett Kaufman
11
posts
Apr 21

Fiberglass over keel smile on 28-III?

(17)
Kevin - It's good to hear from you and all is well with our growing family of grand babies. I always wonder if you are on the bridge as we stay away from the
John Poutier
17
posts
Apr 21

boom vangs and topping lifts

(18)
Additional uses for each. If you have a Dutchman,you'll need the topping lift. A rigid vang with a properly adjusted spring takes the weight of the boom in
Peter Tollini
18
posts
Apr 21

Bildge Pump

(9)
Here's how my bilge pumps are wired. Not the only right way, and maybe not even the way many would do it. But it works for me. * Off each battery, right
Harry K
9
posts
Apr 19

Segue to AIS ?

(32)
I have used mAIS, which is similar, but I think there is one very important caveat to note: While mAIS and other such apps will upload your position and other
David Laino
32
posts
Apr 17

S28 Halyards

(8)
We switched our halyards over to Samson's MLX. Dyneema core with polyester cover. Super strong, so we downsized from 7/16" to 3/8", which makes everything
John Zeratsky
8
posts
Apr 15

Need CNG Cylinder

(9)
Chris, I'm in Europe, I'll call you when I'm back in Canada next Monday. Envoyé de mon iPad ... Chris, I'm in Europe, I'll call you when I'm back in Canada
Michael Lalancette
9
posts
Apr 14

Where Marine Electronics are Going

(9)
I think I'd put a switch near the base of the mast. You need a connector for the radar anyway, and why not tie in the wind and depth sensors? I'd put another
James Starkey
9
posts
Apr 14

chartplotter and radar recommendation

(51)
Stephen, On my 34-I, I have an older NMEA 0183 Garmin chartplotter. Last year, I installed all new N2K transducers (wind and water) and an N2K network, but no
Harry K
51
posts
Apr 13

Pics of faux teak swim steps

(14)
I agree with Roy.  Good looking steps! However with all the teak involved with the Sabres, I don't think that this little bit of plastic makes you entirely
Michael Sims
14
posts
Apr 13

lubricating Sabre 32 impeller

(11)
I think I may replace my speed seal with new version and maybe some Globe impellers. I hope I have my pump model number written down someplace. Speed Seal is
Dan Trainor
11
posts
Apr 8

Best & Worse Things about a Sabre 28?

(12)
Hull/sail # 381 Was named Wisp and was berthed in Rock Hall, Md. Any info on her history would be great.
everwind22
12
posts
Apr 7
View First Topic Go to View Last Topic
Loading 1 - 15 of total 15 topics