Loading ...
Sorry, an error occurred while loading the content.
 

Re: Rl2000 Batteries?

Expand Messages
  • rann_georgia
    You say you just bought it. Was it new or used? I m going to go out on a limb and say you have a bad battery or both. If the battery pack is like the RL1000,
    Message 1 of 24 , Jul 21, 2013
      You say you just bought it. Was it new or used?

      I'm going to go out on a limb and say you have a bad battery or both.

      If the battery pack is like the RL1000, it's two 12v batteries wired in series to get 24 volts. Once I wired mine wrong in parallel. The mower didn't like it and didn't run properly but it worked.

      I'd check the batteries by taking it to an auto parts store. They have a tester that will determine if you have a bad battery. But, usually, a bad battery will quickly shorten the life of the other.

      --- In RoboMower@yahoogroups.com, "mikey0426" <mikey0426@...> wrote:
      >
      > Yes, I am only doing manual depart because I have 3 little kids running around in the back, but I have used max. The first time, it only cut about half the yard before returning. The second time, there were about 7 or 8 stripes. The base zone is only about 0.15ish acre.
      >
      > Thanks
      >
      > --- In RoboMower@yahoogroups.com, Kevin Turner <kevin.turner@> wrote:
      > >
      > > Mine says
      > > 26.3v 9.3v
      > >
      > > No idea what that tells me with regard to how good or bad it is .
      > >
      > > Silly question, but you have set your program to "max" haven't you?
      > >
      > > Sent from my iPad
      > >
      > > On 20 Jul 2013, at 20:18, "Kevin Turner" <kevin.turner@<mailto:kevin.turner@>> wrote:
      > >
      > > I have owned an RL2000 for just over a year. On the program's where it s set to cut for the MAX amount of time, it will keep going for well over 4 hours easily.
      > >
      > > I have never checked the voltage during charging. I'll take a look.....
      > >
      > > Sent from my iPad
      > >
      > > On 20 Jul 2013, at 17:42, "Michael" <mikey0426@<mailto:mikey0426@>> wrote:
      > >
      > >
      > >
      > > Hi there,
      > >
      > > So happy to find this group! Does anyone have experience with the rl2000 yet? I bought one last week, and it cuts great. Problem is, I have yet to get longer than 1 hr 40 min before it returns to base to charge. I know it should last longer than that! After sitting on the dock for 48 hours, the battery information (still in the dock) I get says:
      > >
      > > Charging Voltage 33.6 V
      > > Battery Voltage 25.7V & 9.6V
      > >
      > > Is the information under battery voltage giving the individual battery voltages? I haven't found anywhere on this forum where there are two numbers under battery voltage.
      > >
      > > Just hoping someone could give me some advice on how to proceed....
      > >
      > > Thanks,
      > > Mike
      > >
      > > [Non-text portions of this message have been removed]
      > >
      > >
      > >
      > >
      > > ________________________________
      > > NOTICE: The information in this electronic mail transmission is intended by CoralTree Systems Ltd for the use of the named individuals or entity to which it is directed and may contain information that is privileged or otherwise confidential. If you have received this electronic mail transmission in error, please delete it from your system without copying or forwarding it, and notify the sender of the error by reply email or by telephone, so that the sender's address records can be corrected.
      > >
      > >
      > >
      > > --------------------------------------------------------------------------------
      > >
      > >
      > > CoralTree Systems Limited
      > > 25 Barnes Wallis Road
      > > Segensworth East, Fareham
      > > PO15 5TT
      > >
      > > Company Registration Number 5021022.
      > > Registered Office:
      > > 12-14 Carlton Place
      > > Southampton, UK
      > > SO15 2EA
      > > VAT Registration Number 834 1020 74.
      > >
      > >
      > > [Non-text portions of this message have been removed]
      > >
      >
    • mikey0426
      Just bought it brand new, from Sams club online. I bought a cheap voltmeter, and pulled the power pack from the mower. Each battery read 11V(ish). The back
      Message 2 of 24 , Jul 22, 2013
        Just bought it brand new, from Sams club online.

        I bought a cheap voltmeter, and pulled the power pack from the mower. Each battery read 11V(ish). The back of the power pack read around 23. Not really sure what to do next.....I suppose its possible that the dock is not providing adequate power, since these batteries are brand new......

        Thoughts?

        --- In RoboMower@yahoogroups.com, "rann_georgia" <southbound03@...> wrote:
        >
        > You say you just bought it. Was it new or used?
        >
        > I'm going to go out on a limb and say you have a bad battery or both.
        >
        > If the battery pack is like the RL1000, it's two 12v batteries wired in series to get 24 volts. Once I wired mine wrong in parallel. The mower didn't like it and didn't run properly but it worked.
        >
        > I'd check the batteries by taking it to an auto parts store. They have a tester that will determine if you have a bad battery. But, usually, a bad battery will quickly shorten the life of the other.
        >
        > --- In RoboMower@yahoogroups.com, "mikey0426" <mikey0426@> wrote:
        > >
        > > Yes, I am only doing manual depart because I have 3 little kids running around in the back, but I have used max. The first time, it only cut about half the yard before returning. The second time, there were about 7 or 8 stripes. The base zone is only about 0.15ish acre.
        > >
        > > Thanks
        > >
        > > --- In RoboMower@yahoogroups.com, Kevin Turner <kevin.turner@> wrote:
        > > >
        > > > Mine says
        > > > 26.3v 9.3v
        > > >
        > > > No idea what that tells me with regard to how good or bad it is .
        > > >
        > > > Silly question, but you have set your program to "max" haven't you?
        > > >
        > > > Sent from my iPad
        > > >
        > > > On 20 Jul 2013, at 20:18, "Kevin Turner" <kevin.turner@<mailto:kevin.turner@>> wrote:
        > > >
        > > > I have owned an RL2000 for just over a year. On the program's where it s set to cut for the MAX amount of time, it will keep going for well over 4 hours easily.
        > > >
        > > > I have never checked the voltage during charging. I'll take a look.....
        > > >
        > > > Sent from my iPad
        > > >
        > > > On 20 Jul 2013, at 17:42, "Michael" <mikey0426@<mailto:mikey0426@>> wrote:
        > > >
        > > >
        > > >
        > > > Hi there,
        > > >
        > > > So happy to find this group! Does anyone have experience with the rl2000 yet? I bought one last week, and it cuts great. Problem is, I have yet to get longer than 1 hr 40 min before it returns to base to charge. I know it should last longer than that! After sitting on the dock for 48 hours, the battery information (still in the dock) I get says:
        > > >
        > > > Charging Voltage 33.6 V
        > > > Battery Voltage 25.7V & 9.6V
        > > >
        > > > Is the information under battery voltage giving the individual battery voltages? I haven't found anywhere on this forum where there are two numbers under battery voltage.
        > > >
        > > > Just hoping someone could give me some advice on how to proceed....
        > > >
        > > > Thanks,
        > > > Mike
        > > >
        > > > [Non-text portions of this message have been removed]
        > > >
        > > >
        > > >
        > > >
        > > > ________________________________
        > > > NOTICE: The information in this electronic mail transmission is intended by CoralTree Systems Ltd for the use of the named individuals or entity to which it is directed and may contain information that is privileged or otherwise confidential. If you have received this electronic mail transmission in error, please delete it from your system without copying or forwarding it, and notify the sender of the error by reply email or by telephone, so that the sender's address records can be corrected.
        > > >
        > > >
        > > >
        > > > --------------------------------------------------------------------------------
        > > >
        > > >
        > > > CoralTree Systems Limited
        > > > 25 Barnes Wallis Road
        > > > Segensworth East, Fareham
        > > > PO15 5TT
        > > >
        > > > Company Registration Number 5021022.
        > > > Registered Office:
        > > > 12-14 Carlton Place
        > > > Southampton, UK
        > > > SO15 2EA
        > > > VAT Registration Number 834 1020 74.
        > > >
        > > >
        > > > [Non-text portions of this message have been removed]
        > > >
        > >
        >
      • Tim Wolff
        When fully charged each of the 12v batteries in the pack should measure 13.8V-14.7V. The voltage will vary with ambient temperature. Tim ... [Non-text portions
        Message 3 of 24 , Jul 22, 2013
          When fully charged each of the 12v batteries in the pack should measure 13.8V-14.7V. The voltage will vary with ambient temperature.
          Tim
          > To: RoboMower@yahoogroups.com
          > From: mikey0426@...
          > Date: Tue, 23 Jul 2013 01:48:30 +0000
          > Subject: [RoboMower] Re: Rl2000 Batteries?
          >
          > Just bought it brand new, from Sams club online.
          >
          > I bought a cheap voltmeter, and pulled the power pack from the mower. Each battery read 11V(ish). The back of the power pack read around 23. Not really sure what to do next.....I suppose its possible that the dock is not providing adequate power, since these batteries are brand new......
          >
          > Thoughts?
          >
          > --- In RoboMower@yahoogroups.com, "rann_georgia" <southbound03@...> wrote:
          > >
          > > You say you just bought it. Was it new or used?
          > >
          > > I'm going to go out on a limb and say you have a bad battery or both.
          > >
          > > If the battery pack is like the RL1000, it's two 12v batteries wired in series to get 24 volts. Once I wired mine wrong in parallel. The mower didn't like it and didn't run properly but it worked.
          > >
          > > I'd check the batteries by taking it to an auto parts store. They have a tester that will determine if you have a bad battery. But, usually, a bad battery will quickly shorten the life of the other.
          > >
          > > --- In RoboMower@yahoogroups.com, "mikey0426" <mikey0426@> wrote:
          > > >
          > > > Yes, I am only doing manual depart because I have 3 little kids running around in the back, but I have used max. The first time, it only cut about half the yard before returning. The second time, there were about 7 or 8 stripes. The base zone is only about 0.15ish acre.
          > > >
          > > > Thanks
          > > >
          > > > --- In RoboMower@yahoogroups.com, Kevin Turner <kevin.turner@> wrote:
          > > > >
          > > > > Mine says
          > > > > 26.3v 9.3v
          > > > >
          > > > > No idea what that tells me with regard to how good or bad it is .
          > > > >
          > > > > Silly question, but you have set your program to "max" haven't you?
          > > > >
          > > > > Sent from my iPad
          > > > >
          > > > > On 20 Jul 2013, at 20:18, "Kevin Turner" <kevin.turner@<mailto:kevin.turner@>> wrote:
          > > > >
          > > > > I have owned an RL2000 for just over a year. On the program's where it s set to cut for the MAX amount of time, it will keep going for well over 4 hours easily.
          > > > >
          > > > > I have never checked the voltage during charging. I'll take a look.....
          > > > >
          > > > > Sent from my iPad
          > > > >
          > > > > On 20 Jul 2013, at 17:42, "Michael" <mikey0426@<mailto:mikey0426@>> wrote:
          > > > >
          > > > >
          > > > >
          > > > > Hi there,
          > > > >
          > > > > So happy to find this group! Does anyone have experience with the rl2000 yet? I bought one last week, and it cuts great. Problem is, I have yet to get longer than 1 hr 40 min before it returns to base to charge. I know it should last longer than that! After sitting on the dock for 48 hours, the battery information (still in the dock) I get says:
          > > > >
          > > > > Charging Voltage 33.6 V
          > > > > Battery Voltage 25.7V & 9.6V
          > > > >
          > > > > Is the information under battery voltage giving the individual battery voltages? I haven't found anywhere on this forum where there are two numbers under battery voltage.
          > > > >
          > > > > Just hoping someone could give me some advice on how to proceed....
          > > > >
          > > > > Thanks,
          > > > > Mike
          > > > >
          > > > > [Non-text portions of this message have been removed]
          > > > >
          > > > >
          > > > >
          > > > >
          > > > > ________________________________
          > > > > NOTICE: The information in this electronic mail transmission is intended by CoralTree Systems Ltd for the use of the named individuals or entity to which it is directed and may contain information that is privileged or otherwise confidential. If you have received this electronic mail transmission in error, please delete it from your system without copying or forwarding it, and notify the sender of the error by reply email or by telephone, so that the sender's address records can be corrected.
          > > > >
          > > > >
          > > > >
          > > > > --------------------------------------------------------------------------------
          > > > >
          > > > >
          > > > > CoralTree Systems Limited
          > > > > 25 Barnes Wallis Road
          > > > > Segensworth East, Fareham
          > > > > PO15 5TT
          > > > >
          > > > > Company Registration Number 5021022.
          > > > > Registered Office:
          > > > > 12-14 Carlton Place
          > > > > Southampton, UK
          > > > > SO15 2EA
          > > > > VAT Registration Number 834 1020 74.
          > > > >
          > > > >
          > > > > [Non-text portions of this message have been removed]
          > > > >
          > > >
          > >
          >
          >
          >
          >
          > ------------------------------------
          >
          > Yahoo! Groups Links
          >
          >
          >


          [Non-text portions of this message have been removed]
        • Richard Gard
          Battery is dead. Should read over 25V total It may have sat around a long time. Best wishes, RG ... [Non-text portions of this message have been removed]
          Message 4 of 24 , Jul 22, 2013
            Battery is dead. Should read over 25V total
            It may have sat around a long time.

            Best wishes,
            RG

            On Jul 22, 2013, at 9:48 PM, "mikey0426" <mikey0426@...> wrote:

            > Just bought it brand new, from Sams club online.
            >
            > I bought a cheap voltmeter, and pulled the power pack from the mower. Each battery read 11V(ish). The back of the power pack read around 23. Not really sure what to do next.....I suppose its possible that the dock is not providing adequate power, since these batteries are brand new......
            >
            > Thoughts?
            >
            > --- In RoboMower@yahoogroups.com, "rann_georgia" <southbound03@...> wrote:
            > >
            > > You say you just bought it. Was it new or used?
            > >
            > > I'm going to go out on a limb and say you have a bad battery or both.
            > >
            > > If the battery pack is like the RL1000, it's two 12v batteries wired in series to get 24 volts. Once I wired mine wrong in parallel. The mower didn't like it and didn't run properly but it worked.
            > >
            > > I'd check the batteries by taking it to an auto parts store. They have a tester that will determine if you have a bad battery. But, usually, a bad battery will quickly shorten the life of the other.
            > >
            > > --- In RoboMower@yahoogroups.com, "mikey0426" <mikey0426@> wrote:
            > > >
            > > > Yes, I am only doing manual depart because I have 3 little kids running around in the back, but I have used max. The first time, it only cut about half the yard before returning. The second time, there were about 7 or 8 stripes. The base zone is only about 0.15ish acre.
            > > >
            > > > Thanks
            > > >
            > > > --- In RoboMower@yahoogroups.com, Kevin Turner <kevin.turner@> wrote:
            > > > >
            > > > > Mine says
            > > > > 26.3v 9.3v
            > > > >
            > > > > No idea what that tells me with regard to how good or bad it is .
            > > > >
            > > > > Silly question, but you have set your program to "max" haven't you?
            > > > >
            > > > > Sent from my iPad
            > > > >
            > > > > On 20 Jul 2013, at 20:18, "Kevin Turner" <kevin.turner@<mailto:kevin.turner@>> wrote:
            > > > >
            > > > > I have owned an RL2000 for just over a year. On the program's where it s set to cut for the MAX amount of time, it will keep going for well over 4 hours easily.
            > > > >
            > > > > I have never checked the voltage during charging. I'll take a look.....
            > > > >
            > > > > Sent from my iPad
            > > > >
            > > > > On 20 Jul 2013, at 17:42, "Michael" <mikey0426@<mailto:mikey0426@>> wrote:
            > > > >
            > > > >
            > > > >
            > > > > Hi there,
            > > > >
            > > > > So happy to find this group! Does anyone have experience with the rl2000 yet? I bought one last week, and it cuts great. Problem is, I have yet to get longer than 1 hr 40 min before it returns to base to charge. I know it should last longer than that! After sitting on the dock for 48 hours, the battery information (still in the dock) I get says:
            > > > >
            > > > > Charging Voltage 33.6 V
            > > > > Battery Voltage 25.7V & 9.6V
            > > > >
            > > > > Is the information under battery voltage giving the individual battery voltages? I haven't found anywhere on this forum where there are two numbers under battery voltage.
            > > > >
            > > > > Just hoping someone could give me some advice on how to proceed....
            > > > >
            > > > > Thanks,
            > > > > Mike
            > > > >
            > > > > [Non-text portions of this message have been removed]
            > > > >
            > > > >
            > > > >
            > > > >
            > > > > ________________________________
            > > > > NOTICE: The information in this electronic mail transmission is intended by CoralTree Systems Ltd for the use of the named individuals or entity to which it is directed and may contain information that is privileged or otherwise confidential. If you have received this electronic mail transmission in error, please delete it from your system without copying or forwarding it, and notify the sender of the error by reply email or by telephone, so that the sender's address records can be corrected.
            > > > >
            > > > >
            > > > >
            > > > > ----------------------------------------------------------
            > > > >
            > > > >
            > > > > CoralTree Systems Limited
            > > > > 25 Barnes Wallis Road
            > > > > Segensworth East, Fareham
            > > > > PO15 5TT
            > > > >
            > > > > Company Registration Number 5021022.
            > > > > Registered Office:
            > > > > 12-14 Carlton Place
            > > > > Southampton, UK
            > > > > SO15 2EA
            > > > > VAT Registration Number 834 1020 74.
            > > > >
            > > > >
            > > > > [Non-text portions of this message have been removed]
            > > > >
            > > >
            > >
            >
            >


            [Non-text portions of this message have been removed]
          • Kevin Turner
            Don t they provide an after sales service? Buying it online does not mean you have no warranty rights. By the way, my RL2000 battery pack is a sealed single
            Message 5 of 24 , Jul 23, 2013
              Don't they provide an after sales service? Buying it online does not mean you have no warranty rights.

              By the way, my RL2000 battery pack is a sealed single unit, in which there are 2x17AH 24V sealed lead acid batteries. Average mowing time 3 hours 20 (but as I say it goes for we'll over 4 hours)

              On 23 Jul 2013, at 03:08, "mikey0426" <mikey0426@...<mailto:mikey0426@...>> wrote:



              Just bought it brand new, from Sams club online.

              I bought a cheap voltmeter, and pulled the power pack from the mower. Each battery read 11V(ish). The back of the power pack read around 23. Not really sure what to do next.....I suppose its possible that the dock is not providing adequate power, since these batteries are brand new......

              Thoughts?

              --- In RoboMower@yahoogroups.com<mailto:RoboMower%40yahoogroups.com>, "rann_georgia" <southbound03@...> wrote:
              >
              > You say you just bought it. Was it new or used?
              >
              > I'm going to go out on a limb and say you have a bad battery or both.
              >
              > If the battery pack is like the RL1000, it's two 12v batteries wired in series to get 24 volts. Once I wired mine wrong in parallel. The mower didn't like it and didn't run properly but it worked.
              >
              > I'd check the batteries by taking it to an auto parts store. They have a tester that will determine if you have a bad battery. But, usually, a bad battery will quickly shorten the life of the other.
              >
              > --- In RoboMower@yahoogroups.com<mailto:RoboMower%40yahoogroups.com>, "mikey0426" <mikey0426@> wrote:
              > >
              > > Yes, I am only doing manual depart because I have 3 little kids running around in the back, but I have used max. The first time, it only cut about half the yard before returning. The second time, there were about 7 or 8 stripes. The base zone is only about 0.15ish acre.
              > >
              > > Thanks
              > >
              > > --- In RoboMower@yahoogroups.com<mailto:RoboMower%40yahoogroups.com>, Kevin Turner <kevin.turner@> wrote:
              > > >
              > > > Mine says
              > > > 26.3v 9.3v
              > > >
              > > > No idea what that tells me with regard to how good or bad it is .
              > > >
              > > > Silly question, but you have set your program to "max" haven't you?
              > > >
              > > > Sent from my iPad
              > > >
              > > > On 20 Jul 2013, at 20:18, "Kevin Turner" <kevin.turner@<mailto:kevin.turner@>> wrote:
              > > >
              > > > I have owned an RL2000 for just over a year. On the program's where it s set to cut for the MAX amount of time, it will keep going for well over 4 hours easily.
              > > >
              > > > I have never checked the voltage during charging. I'll take a look.....
              > > >
              > > > Sent from my iPad
              > > >
              > > > On 20 Jul 2013, at 17:42, "Michael" <mikey0426@<mailto:mikey0426@>> wrote:
              > > >
              > > >
              > > >
              > > > Hi there,
              > > >
              > > > So happy to find this group! Does anyone have experience with the rl2000 yet? I bought one last week, and it cuts great. Problem is, I have yet to get longer than 1 hr 40 min before it returns to base to charge. I know it should last longer than that! After sitting on the dock for 48 hours, the battery information (still in the dock) I get says:
              > > >
              > > > Charging Voltage 33.6 V
              > > > Battery Voltage 25.7V & 9.6V
              > > >
              > > > Is the information under battery voltage giving the individual battery voltages? I haven't found anywhere on this forum where there are two numbers under battery voltage.
              > > >
              > > > Just hoping someone could give me some advice on how to proceed....
              > > >
              > > > Thanks,
              > > > Mike
              > > >
              > > > [Non-text portions of this message have been removed]
              > > >
              > > >
              > > >
              > > >
              > > > ________________________________
              > > > NOTICE: The information in this electronic mail transmission is intended by CoralTree Systems Ltd for the use of the named individuals or entity to which it is directed and may contain information that is privileged or otherwise confidential. If you have received this electronic mail transmission in error, please delete it from your system without copying or forwarding it, and notify the sender of the error by reply email or by telephone, so that the sender's address records can be corrected.
              > > >
              > > >
              > > >
              > > > ----------------------------------------------------------
              > > >
              > > >
              > > > CoralTree Systems Limited
              > > > 25 Barnes Wallis Road
              > > > Segensworth East, Fareham
              > > > PO15 5TT
              > > >
              > > > Company Registration Number 5021022.
              > > > Registered Office:
              > > > 12-14 Carlton Place
              > > > Southampton, UK
              > > > SO15 2EA
              > > > VAT Registration Number 834 1020 74.
              > > >
              > > >
              > > > [Non-text portions of this message have been removed]
              > > >
              > >
              >




              ________________________________
              NOTICE: The information in this electronic mail transmission is intended by CoralTree Systems Ltd for the use of the named individuals or entity to which it is directed and may contain information that is privileged or otherwise confidential. If you have received this electronic mail transmission in error, please delete it from your system without copying or forwarding it, and notify the sender of the error by reply email or by telephone, so that the sender's address records can be corrected.



              --------------------------------------------------------------------------------


              CoralTree Systems Limited
              25 Barnes Wallis Road
              Segensworth East, Fareham
              PO15 5TT

              Company Registration Number 5021022.
              Registered Office:
              12-14 Carlton Place
              Southampton, UK
              SO15 2EA
              VAT Registration Number 834 1020 74.


              [Non-text portions of this message have been removed]
            • Kevin Turner
              There are 2x17AH 24V sealed lead acid in an RL2000 On 23 Jul 2013, at 03:13, Tim Wolff wrote: When fully
              Message 6 of 24 , Jul 23, 2013
                There are 2x17AH 24V sealed lead acid in an RL2000

                On 23 Jul 2013, at 03:13, "Tim Wolff" <twolff69@...<mailto:twolff69@...>> wrote:



                When fully charged each of the 12v batteries in the pack should measure 13.8V-14.7V. The voltage will vary with ambient temperature.
                Tim
                > To: RoboMower@yahoogroups.com<mailto:RoboMower%40yahoogroups.com>
                > From: mikey0426@...<mailto:mikey0426%40yahoo.com>
                > Date: Tue, 23 Jul 2013 01:48:30 +0000
                > Subject: [RoboMower] Re: Rl2000 Batteries?
                >
                > Just bought it brand new, from Sams club online.
                >
                > I bought a cheap voltmeter, and pulled the power pack from the mower. Each battery read 11V(ish). The back of the power pack read around 23. Not really sure what to do next.....I suppose its possible that the dock is not providing adequate power, since these batteries are brand new......
                >
                > Thoughts?
                >
                > --- In RoboMower@yahoogroups.com<mailto:RoboMower%40yahoogroups.com>, "rann_georgia" <southbound03@...> wrote:
                > >
                > > You say you just bought it. Was it new or used?
                > >
                > > I'm going to go out on a limb and say you have a bad battery or both.
                > >
                > > If the battery pack is like the RL1000, it's two 12v batteries wired in series to get 24 volts. Once I wired mine wrong in parallel. The mower didn't like it and didn't run properly but it worked.
                > >
                > > I'd check the batteries by taking it to an auto parts store. They have a tester that will determine if you have a bad battery. But, usually, a bad battery will quickly shorten the life of the other.
                > >
                > > --- In RoboMower@yahoogroups.com<mailto:RoboMower%40yahoogroups.com>, "mikey0426" <mikey0426@> wrote:
                > > >
                > > > Yes, I am only doing manual depart because I have 3 little kids running around in the back, but I have used max. The first time, it only cut about half the yard before returning. The second time, there were about 7 or 8 stripes. The base zone is only about 0.15ish acre.
                > > >
                > > > Thanks
                > > >
                > > > --- In RoboMower@yahoogroups.com<mailto:RoboMower%40yahoogroups.com>, Kevin Turner <kevin.turner@> wrote:
                > > > >
                > > > > Mine says
                > > > > 26.3v 9.3v
                > > > >
                > > > > No idea what that tells me with regard to how good or bad it is .
                > > > >
                > > > > Silly question, but you have set your program to "max" haven't you?
                > > > >
                > > > > Sent from my iPad
                > > > >
                > > > > On 20 Jul 2013, at 20:18, "Kevin Turner" <kevin.turner@<mailto:kevin.turner@>> wrote:
                > > > >
                > > > > I have owned an RL2000 for just over a year. On the program's where it s set to cut for the MAX amount of time, it will keep going for well over 4 hours easily.
                > > > >
                > > > > I have never checked the voltage during charging. I'll take a look.....
                > > > >
                > > > > Sent from my iPad
                > > > >
                > > > > On 20 Jul 2013, at 17:42, "Michael" <mikey0426@<mailto:mikey0426@>> wrote:
                > > > >
                > > > >
                > > > >
                > > > > Hi there,
                > > > >
                > > > > So happy to find this group! Does anyone have experience with the rl2000 yet? I bought one last week, and it cuts great. Problem is, I have yet to get longer than 1 hr 40 min before it returns to base to charge. I know it should last longer than that! After sitting on the dock for 48 hours, the battery information (still in the dock) I get says:
                > > > >
                > > > > Charging Voltage 33.6 V
                > > > > Battery Voltage 25.7V & 9.6V
                > > > >
                > > > > Is the information under battery voltage giving the individual battery voltages? I haven't found anywhere on this forum where there are two numbers under battery voltage.
                > > > >
                > > > > Just hoping someone could give me some advice on how to proceed....
                > > > >
                > > > > Thanks,
                > > > > Mike
                > > > >
                > > > > [Non-text portions of this message have been removed]
                > > > >
                > > > >
                > > > >
                > > > >
                > > > > ________________________________
                > > > > NOTICE: The information in this electronic mail transmission is intended by CoralTree Systems Ltd for the use of the named individuals or entity to which it is directed and may contain information that is privileged or otherwise confidential. If you have received this electronic mail transmission in error, please delete it from your system without copying or forwarding it, and notify the sender of the error by reply email or by telephone, so that the sender's address records can be corrected.
                > > > >
                > > > >
                > > > >
                > > > > ----------------------------------------------------------
                > > > >
                > > > >
                > > > > CoralTree Systems Limited
                > > > > 25 Barnes Wallis Road
                > > > > Segensworth East, Fareham
                > > > > PO15 5TT
                > > > >
                > > > > Company Registration Number 5021022.
                > > > > Registered Office:
                > > > > 12-14 Carlton Place
                > > > > Southampton, UK
                > > > > SO15 2EA
                > > > > VAT Registration Number 834 1020 74.
                > > > >
                > > > >
                > > > > [Non-text portions of this message have been removed]
                > > > >
                > > >
                > >
                >
                >
                >
                >
                > ------------------------------------
                >
                > Yahoo! Groups Links
                >
                >
                >


                [Non-text portions of this message have been removed]




                ________________________________
                NOTICE: The information in this electronic mail transmission is intended by CoralTree Systems Ltd for the use of the named individuals or entity to which it is directed and may contain information that is privileged or otherwise confidential. If you have received this electronic mail transmission in error, please delete it from your system without copying or forwarding it, and notify the sender of the error by reply email or by telephone, so that the sender's address records can be corrected.



                --------------------------------------------------------------------------------


                CoralTree Systems Limited
                25 Barnes Wallis Road
                Segensworth East, Fareham
                PO15 5TT

                Company Registration Number 5021022.
                Registered Office:
                12-14 Carlton Place
                Southampton, UK
                SO15 2EA
                VAT Registration Number 834 1020 74.


                [Non-text portions of this message have been removed]
              • Dan Barclay
                You can use automatic, at night when the kids are asleep. The mower doesn t care if it s dark and it s not very loud. Dan From: RoboMower@yahoogroups.com
                Message 7 of 24 , Jul 23, 2013
                  You can use automatic, at night when the kids are asleep.



                  The mower doesn't care if it's dark and it's not very loud.



                  Dan



                  From: RoboMower@yahoogroups.com [mailto:RoboMower@yahoogroups.com] On Behalf
                  Of mikey0426
                  Sent: Saturday, July 20, 2013 6:25 PM
                  To: RoboMower@yahoogroups.com
                  Subject: [RoboMower] Re: Rl2000 Batteries?





                  Yes, I am only doing manual depart because I have 3 little kids running
                  around in the back, but I have used max. The first time, it only cut about
                  half the yard before returning. The second time, there were about 7 or 8
                  stripes. The base zone is only about 0.15ish acre.

                  Thanks

                  --- In RoboMower@yahoogroups.com <mailto:RoboMower%40yahoogroups.com> ,
                  Kevin Turner <kevin.turner@...> wrote:
                  >
                  > Mine says
                  > 26.3v 9.3v
                  >
                  > No idea what that tells me with regard to how good or bad it is .
                  >
                  > Silly question, but you have set your program to "max" haven't you?
                  >
                  > Sent from my iPad
                  >
                  > On 20 Jul 2013, at 20:18, "Kevin Turner" <kevin.turner@...
                  <mailto:kevin.turner@...%3cmailto:kevin.turner@...>
                  <mailto:kevin.turner@...>> wrote:
                  >
                  > I have owned an RL2000 for just over a year. On the program's where it s
                  set to cut for the MAX amount of time, it will keep going for well over 4
                  hours easily.
                  >
                  > I have never checked the voltage during charging. I'll take a look.....
                  >
                  > Sent from my iPad
                  >
                  > On 20 Jul 2013, at 17:42, "Michael" <mikey0426@...
                  <mailto:mikey0426@...%3cmailto:mikey0426@...> <mailto:mikey0426@...>> wrote:
                  >
                  >
                  >
                  > Hi there,
                  >
                  > So happy to find this group! Does anyone have experience with the rl2000
                  yet? I bought one last week, and it cuts great. Problem is, I have yet to
                  get longer than 1 hr 40 min before it returns to base to charge. I know it
                  should last longer than that! After sitting on the dock for 48 hours, the
                  battery information (still in the dock) I get says:
                  >
                  > Charging Voltage 33.6 V
                  > Battery Voltage 25.7V & 9.6V
                  >
                  > Is the information under battery voltage giving the individual battery
                  voltages? I haven't found anywhere on this forum where there are two numbers
                  under battery voltage.
                  >
                  > Just hoping someone could give me some advice on how to proceed....
                  >
                  > Thanks,
                  > Mike
                  >
                  > [Non-text portions of this message have been removed]
                  >
                  >
                  >
                  >
                  > ________________________________
                  > NOTICE: The information in this electronic mail transmission is intended
                  by CoralTree Systems Ltd for the use of the named individuals or entity to
                  which it is directed and may contain information that is privileged or
                  otherwise confidential. If you have received this electronic mail
                  transmission in error, please delete it from your system without copying or
                  forwarding it, and notify the sender of the error by reply email or by
                  telephone, so that the sender's address records can be corrected.
                  >
                  >
                  >
                  > ----------------------------------------------------------
                  >
                  >
                  > CoralTree Systems Limited
                  > 25 Barnes Wallis Road
                  > Segensworth East, Fareham
                  > PO15 5TT
                  >
                  > Company Registration Number 5021022.
                  > Registered Office:
                  > 12-14 Carlton Place
                  > Southampton, UK
                  > SO15 2EA
                  > VAT Registration Number 834 1020 74.
                  >
                  >
                  > [Non-text portions of this message have been removed]
                  >





                  [Non-text portions of this message have been removed]
                • Ben
                  You can use automatic, at night when the kids are asleep. The mower doesn t care if it s dark and it s not very loud. Dan It s not the kids or pets I worry
                  Message 8 of 24 , Jul 23, 2013
                    "You can use automatic, at night when the kids are asleep.

                    The mower doesn't care if it's dark and it's not very loud.

                    Dan"

                    It's not the kids or pets I worry about..... they can move! It's the toys,
                    garden hose, tree branches, and who knows what else was left out there this
                    time that I worry about.


                    On Tue, Jul 23, 2013 at 12:55 PM, Dan Barclay <Dan@...>wrote:

                    > **
                    >
                    >
                    > You can use automatic, at night when the kids are asleep.
                    >
                    > The mower doesn't care if it's dark and it's not very loud.
                    >
                    > Dan
                    >
                    >
                    > From: RoboMower@yahoogroups.com [mailto:RoboMower@yahoogroups.com] On
                    > Behalf
                    > Of mikey0426
                    > Sent: Saturday, July 20, 2013 6:25 PM
                    > To: RoboMower@yahoogroups.com
                    >
                    > Subject: [RoboMower] Re: Rl2000 Batteries?
                    >
                    > Yes, I am only doing manual depart because I have 3 little kids running
                    > around in the back, but I have used max. The first time, it only cut about
                    > half the yard before returning. The second time, there were about 7 or 8
                    > stripes. The base zone is only about 0.15ish acre.
                    >
                    > Thanks
                    >
                    > --- In RoboMower@yahoogroups.com <mailto:RoboMower%40yahoogroups.com> ,
                    >
                    > Kevin Turner <kevin.turner@...> wrote:
                    > >
                    > > Mine says
                    > > 26.3v 9.3v
                    > >
                    > > No idea what that tells me with regard to how good or bad it is .
                    > >
                    > > Silly question, but you have set your program to "max" haven't you?
                    > >
                    > > Sent from my iPad
                    > >
                    > > On 20 Jul 2013, at 20:18, "Kevin Turner" <kevin.turner@...
                    > <mailto:kevin.turner@...%3cmailto:kevin.turner@...>
                    >
                    > <mailto:kevin.turner@...>> wrote:
                    > >
                    > > I have owned an RL2000 for just over a year. On the program's where it s
                    > set to cut for the MAX amount of time, it will keep going for well over 4
                    > hours easily.
                    > >
                    > > I have never checked the voltage during charging. I'll take a look.....
                    > >
                    > > Sent from my iPad
                    > >
                    > > On 20 Jul 2013, at 17:42, "Michael" <mikey0426@...
                    > <mailto:mikey0426@...%3cmailto:mikey0426@...> <mailto:mikey0426@...>>
                    > wrote:
                    > >
                    > >
                    > >
                    > > Hi there,
                    > >
                    > > So happy to find this group! Does anyone have experience with the rl2000
                    > yet? I bought one last week, and it cuts great. Problem is, I have yet to
                    > get longer than 1 hr 40 min before it returns to base to charge. I know it
                    > should last longer than that! After sitting on the dock for 48 hours, the
                    > battery information (still in the dock) I get says:
                    > >
                    > > Charging Voltage 33.6 V
                    > > Battery Voltage 25.7V & 9.6V
                    > >
                    > > Is the information under battery voltage giving the individual battery
                    > voltages? I haven't found anywhere on this forum where there are two
                    > numbers
                    > under battery voltage.
                    > >
                    > > Just hoping someone could give me some advice on how to proceed....
                    > >
                    > > Thanks,
                    > > Mike
                    > >
                    > > [Non-text portions of this message have been removed]
                    > >
                    > >
                    > >
                    > >
                    > > ________________________________
                    > > NOTICE: The information in this electronic mail transmission is intended
                    > by CoralTree Systems Ltd for the use of the named individuals or entity to
                    > which it is directed and may contain information that is privileged or
                    > otherwise confidential. If you have received this electronic mail
                    > transmission in error, please delete it from your system without copying or
                    > forwarding it, and notify the sender of the error by reply email or by
                    > telephone, so that the sender's address records can be corrected.
                    > >
                    > >
                    > >
                    > > ----------------------------------------------------------
                    > >
                    > >
                    > > CoralTree Systems Limited
                    > > 25 Barnes Wallis Road
                    > > Segensworth East, Fareham
                    > > PO15 5TT
                    > >
                    > > Company Registration Number 5021022.
                    > > Registered Office:
                    > > 12-14 Carlton Place
                    > > Southampton, UK
                    > > SO15 2EA
                    > > VAT Registration Number 834 1020 74.
                    > >
                    > >
                    > > [Non-text portions of this message have been removed]
                    > >
                    >
                    > [Non-text portions of this message have been removed]
                    >
                    >
                    >


                    [Non-text portions of this message have been removed]
                  • rann_georgia
                    Bad batteries can and do work for shorter periods. Since it s new, I hate to tell you to pop that battery pack open and unshort the wires. There is a voltage
                    Message 9 of 24 , Jul 23, 2013
                      Bad batteries can and do work for shorter periods.

                      Since it's new, I hate to tell you to pop that battery pack open and unshort the wires.

                      There is a voltage meter that's about 70 bucks or so that can measure whether a battery is bad, not just the voltage. As far as I know, they do this on 12v batteries only. I'm a minus for Batteries Plus
                      because they replaced the original battery with a cheaper model and have done so every year for the last three running.

                      I'm still going with bad battery pack.

                      You try a few unorthodox things. The man who runs Probotics is very knowledgeable and helpful. You might catch him on a slow day and he'll talk your ear off. You could try calling that dealership and I'm sure he's experienced almost everything related to these things.




                      --- In RoboMower@yahoogroups.com, "mikey0426" <mikey0426@...> wrote:
                      >
                      > Just bought it brand new, from Sams club online.
                      >
                      > I bought a cheap voltmeter, and pulled the power pack from the mower. Each battery read 11V(ish). The back of the power pack read around 23. Not really sure what to do next.....I suppose its possible that the dock is not providing adequate power, since these batteries are brand new......
                      >
                      > Thoughts?
                      >
                      > --- In RoboMower@yahoogroups.com, "rann_georgia" <southbound03@> wrote:
                      > >
                      > > You say you just bought it. Was it new or used?
                      > >
                      > > I'm going to go out on a limb and say you have a bad battery or both.
                      > >
                      > > If the battery pack is like the RL1000, it's two 12v batteries wired in series to get 24 volts. Once I wired mine wrong in parallel. The mower didn't like it and didn't run properly but it worked.
                      > >
                      > > I'd check the batteries by taking it to an auto parts store. They have a tester that will determine if you have a bad battery. But, usually, a bad battery will quickly shorten the life of the other.
                      > >
                      > > --- In RoboMower@yahoogroups.com, "mikey0426" <mikey0426@> wrote:
                      > > >
                      > > > Yes, I am only doing manual depart because I have 3 little kids running around in the back, but I have used max. The first time, it only cut about half the yard before returning. The second time, there were about 7 or 8 stripes. The base zone is only about 0.15ish acre.
                      > > >
                      > > > Thanks
                      > > >
                      > > > --- In RoboMower@yahoogroups.com, Kevin Turner <kevin.turner@> wrote:
                      > > > >
                      > > > > Mine says
                      > > > > 26.3v 9.3v
                      > > > >
                      > > > > No idea what that tells me with regard to how good or bad it is .
                      > > > >
                      > > > > Silly question, but you have set your program to "max" haven't you?
                      > > > >
                      > > > > Sent from my iPad
                      > > > >
                      > > > > On 20 Jul 2013, at 20:18, "Kevin Turner" <kevin.turner@<mailto:kevin.turner@>> wrote:
                      > > > >
                      > > > > I have owned an RL2000 for just over a year. On the program's where it s set to cut for the MAX amount of time, it will keep going for well over 4 hours easily.
                      > > > >
                      > > > > I have never checked the voltage during charging. I'll take a look.....
                      > > > >
                      > > > > Sent from my iPad
                      > > > >
                      > > > > On 20 Jul 2013, at 17:42, "Michael" <mikey0426@<mailto:mikey0426@>> wrote:
                      > > > >
                      > > > >
                      > > > >
                      > > > > Hi there,
                      > > > >
                      > > > > So happy to find this group! Does anyone have experience with the rl2000 yet? I bought one last week, and it cuts great. Problem is, I have yet to get longer than 1 hr 40 min before it returns to base to charge. I know it should last longer than that! After sitting on the dock for 48 hours, the battery information (still in the dock) I get says:
                      > > > >
                      > > > > Charging Voltage 33.6 V
                      > > > > Battery Voltage 25.7V & 9.6V
                      > > > >
                      > > > > Is the information under battery voltage giving the individual battery voltages? I haven't found anywhere on this forum where there are two numbers under battery voltage.
                      > > > >
                      > > > > Just hoping someone could give me some advice on how to proceed....
                      > > > >
                      > > > > Thanks,
                      > > > > Mike
                      > > > >
                      > > > > [Non-text portions of this message have been removed]
                      > > > >
                      > > > >
                      > > > >
                      > > > >
                      > > > > ________________________________
                      > > > > NOTICE: The information in this electronic mail transmission is intended by CoralTree Systems Ltd for the use of the named individuals or entity to which it is directed and may contain information that is privileged or otherwise confidential. If you have received this electronic mail transmission in error, please delete it from your system without copying or forwarding it, and notify the sender of the error by reply email or by telephone, so that the sender's address records can be corrected.
                      > > > >
                      > > > >
                      > > > >
                      > > > > --------------------------------------------------------------------------------
                      > > > >
                      > > > >
                      > > > > CoralTree Systems Limited
                      > > > > 25 Barnes Wallis Road
                      > > > > Segensworth East, Fareham
                      > > > > PO15 5TT
                      > > > >
                      > > > > Company Registration Number 5021022.
                      > > > > Registered Office:
                      > > > > 12-14 Carlton Place
                      > > > > Southampton, UK
                      > > > > SO15 2EA
                      > > > > VAT Registration Number 834 1020 74.
                      > > > >
                      > > > >
                      > > > > [Non-text portions of this message have been removed]
                      > > > >
                      > > >
                      > >
                      >
                    • rann_georgia
                      the only problem that I see running it at night is doo. The grass could be wet and that creates more resistance. More resistance takes more power meaning
                      Message 10 of 24 , Jul 23, 2013
                        the only problem that I see running it at night is doo. The grass could be wet and that creates more resistance. More resistance takes more power meaning shorter mowing times.

                        My mower has glided right over power cords, hoses and such. The major problem I have is making sure the car is not in the zone as it will get stuck under it.

                        BTW, I do like the idea someone else had of using a knife sharpener on the blades for a touch up.

                        --- In RoboMower@yahoogroups.com, Ben <ben.jordan@...> wrote:
                        >
                        > "You can use automatic, at night when the kids are asleep.
                        >
                        > The mower doesn't care if it's dark and it's not very loud.
                        >
                        > Dan"
                        >
                        > It's not the kids or pets I worry about..... they can move! It's the toys,
                        > garden hose, tree branches, and who knows what else was left out there this
                        > time that I worry about.
                        >
                        >
                        > On Tue, Jul 23, 2013 at 12:55 PM, Dan Barclay <Dan@...>wrote:
                        >
                        > > **
                        > >
                        > >
                        > > You can use automatic, at night when the kids are asleep.
                        > >
                        > > The mower doesn't care if it's dark and it's not very loud.
                        > >
                        > > Dan
                        > >
                        > >
                        > > From: RoboMower@yahoogroups.com [mailto:RoboMower@yahoogroups.com] On
                        > > Behalf
                        > > Of mikey0426
                        > > Sent: Saturday, July 20, 2013 6:25 PM
                        > > To: RoboMower@yahoogroups.com
                        > >
                        > > Subject: [RoboMower] Re: Rl2000 Batteries?
                        > >
                        > > Yes, I am only doing manual depart because I have 3 little kids running
                        > > around in the back, but I have used max. The first time, it only cut about
                        > > half the yard before returning. The second time, there were about 7 or 8
                        > > stripes. The base zone is only about 0.15ish acre.
                        > >
                        > > Thanks
                        > >
                        > > --- In RoboMower@yahoogroups.com <mailto:RoboMower%40yahoogroups.com> ,
                        > >
                        > > Kevin Turner <kevin.turner@> wrote:
                        > > >
                        > > > Mine says
                        > > > 26.3v 9.3v
                        > > >
                        > > > No idea what that tells me with regard to how good or bad it is .
                        > > >
                        > > > Silly question, but you have set your program to "max" haven't you?
                        > > >
                        > > > Sent from my iPad
                        > > >
                        > > > On 20 Jul 2013, at 20:18, "Kevin Turner" <kevin.turner@
                        > > <mailto:kevin.turner@%3cmailto:kevin.turner@>
                        > >
                        > > <mailto:kevin.turner@>> wrote:
                        > > >
                        > > > I have owned an RL2000 for just over a year. On the program's where it s
                        > > set to cut for the MAX amount of time, it will keep going for well over 4
                        > > hours easily.
                        > > >
                        > > > I have never checked the voltage during charging. I'll take a look.....
                        > > >
                        > > > Sent from my iPad
                        > > >
                        > > > On 20 Jul 2013, at 17:42, "Michael" <mikey0426@
                        > > <mailto:mikey0426@%3cmailto:mikey0426@> <mailto:mikey0426@>>
                        > > wrote:
                        > > >
                        > > >
                        > > >
                        > > > Hi there,
                        > > >
                        > > > So happy to find this group! Does anyone have experience with the rl2000
                        > > yet? I bought one last week, and it cuts great. Problem is, I have yet to
                        > > get longer than 1 hr 40 min before it returns to base to charge. I know it
                        > > should last longer than that! After sitting on the dock for 48 hours, the
                        > > battery information (still in the dock) I get says:
                        > > >
                        > > > Charging Voltage 33.6 V
                        > > > Battery Voltage 25.7V & 9.6V
                        > > >
                        > > > Is the information under battery voltage giving the individual battery
                        > > voltages? I haven't found anywhere on this forum where there are two
                        > > numbers
                        > > under battery voltage.
                        > > >
                        > > > Just hoping someone could give me some advice on how to proceed....
                        > > >
                        > > > Thanks,
                        > > > Mike
                        > > >
                        > > > [Non-text portions of this message have been removed]
                        > > >
                        > > >
                        > > >
                        > > >
                        > > > ________________________________
                        > > > NOTICE: The information in this electronic mail transmission is intended
                        > > by CoralTree Systems Ltd for the use of the named individuals or entity to
                        > > which it is directed and may contain information that is privileged or
                        > > otherwise confidential. If you have received this electronic mail
                        > > transmission in error, please delete it from your system without copying or
                        > > forwarding it, and notify the sender of the error by reply email or by
                        > > telephone, so that the sender's address records can be corrected.
                        > > >
                        > > >
                        > > >
                        > > > ----------------------------------------------------------
                        > > >
                        > > >
                        > > > CoralTree Systems Limited
                        > > > 25 Barnes Wallis Road
                        > > > Segensworth East, Fareham
                        > > > PO15 5TT
                        > > >
                        > > > Company Registration Number 5021022.
                        > > > Registered Office:
                        > > > 12-14 Carlton Place
                        > > > Southampton, UK
                        > > > SO15 2EA
                        > > > VAT Registration Number 834 1020 74.
                        > > >
                        > > >
                        > > > [Non-text portions of this message have been removed]
                        > > >
                        > >
                        > > [Non-text portions of this message have been removed]
                        > >
                        > >
                        > >
                        >
                        >
                        > [Non-text portions of this message have been removed]
                        >
                      • Danny Miller
                        Not all weather conditions produce dew on every night. But I ll say right now, wet grass DOES suck. Not just because of resistance, it can cake up inside the
                        Message 11 of 24 , Jul 23, 2013
                          Not all weather conditions produce dew on every night.

                          But I'll say right now, wet grass DOES suck. Not just because of
                          resistance, it can cake up inside the blade wells and it'll mostly stop
                          cutting when that happens.

                          Danny

                          On 7/23/2013 1:58 PM, rann_georgia wrote:
                          > the only problem that I see running it at night is doo. The grass could be wet and that creates more resistance. More resistance takes more power meaning shorter mowing times.
                          >
                          > My mower has glided right over power cords, hoses and such. The major problem I have is making sure the car is not in the zone as it will get stuck under it.
                          >
                          > BTW, I do like the idea someone else had of using a knife sharpener on the blades for a touch up.
                          >
                          > --- In RoboMower@yahoogroups.com, Ben <ben.jordan@...> wrote:
                          >> "You can use automatic, at night when the kids are asleep.
                          >>
                          >> The mower doesn't care if it's dark and it's not very loud.
                          >>
                          >> Dan"
                          >>
                          >> It's not the kids or pets I worry about..... they can move! It's the toys,
                          >> garden hose, tree branches, and who knows what else was left out there this
                          >> time that I worry about.
                          >>
                          >>
                          >> On Tue, Jul 23, 2013 at 12:55 PM, Dan Barclay <Dan@...>wrote:
                          >>
                          >>> **
                          >>>
                          >>>
                          >>> You can use automatic, at night when the kids are asleep.
                          >>>
                          >>> The mower doesn't care if it's dark and it's not very loud.
                          >>>
                          >>> Dan
                          >>>
                          >>>
                          >>> From: RoboMower@yahoogroups.com [mailto:RoboMower@yahoogroups.com] On
                          >>> Behalf
                          >>> Of mikey0426
                          >>> Sent: Saturday, July 20, 2013 6:25 PM
                          >>> To: RoboMower@yahoogroups.com
                          >>>
                          >>> Subject: [RoboMower] Re: Rl2000 Batteries?
                          >>>
                          >>> Yes, I am only doing manual depart because I have 3 little kids running
                          >>> around in the back, but I have used max. The first time, it only cut about
                          >>> half the yard before returning. The second time, there were about 7 or 8
                          >>> stripes. The base zone is only about 0.15ish acre.
                          >>>
                          >>> Thanks
                          >>>
                          >>> --- In RoboMower@yahoogroups.com <mailto:RoboMower%40yahoogroups.com> ,
                          >>>
                          >>> Kevin Turner <kevin.turner@> wrote:
                          >>>> Mine says
                          >>>> 26.3v 9.3v
                          >>>>
                          >>>> No idea what that tells me with regard to how good or bad it is .
                          >>>>
                          >>>> Silly question, but you have set your program to "max" haven't you?
                          >>>>
                          >>>> Sent from my iPad
                          >>>>
                          >>>> On 20 Jul 2013, at 20:18, "Kevin Turner" <kevin.turner@
                          >>> <mailto:kevin.turner@%3cmailto:kevin.turner@>
                          >>>
                          >>> <mailto:kevin.turner@>> wrote:
                          >>>> I have owned an RL2000 for just over a year. On the program's where it s
                          >>> set to cut for the MAX amount of time, it will keep going for well over 4
                          >>> hours easily.
                          >>>> I have never checked the voltage during charging. I'll take a look.....
                          >>>>
                          >>>> Sent from my iPad
                          >>>>
                          >>>> On 20 Jul 2013, at 17:42, "Michael" <mikey0426@
                          >>> <mailto:mikey0426@%3cmailto:mikey0426@> <mailto:mikey0426@>>
                          >>> wrote:
                          >>>>
                          >>>>
                          >>>> Hi there,
                          >>>>
                          >>>> So happy to find this group! Does anyone have experience with the rl2000
                          >>> yet? I bought one last week, and it cuts great. Problem is, I have yet to
                          >>> get longer than 1 hr 40 min before it returns to base to charge. I know it
                          >>> should last longer than that! After sitting on the dock for 48 hours, the
                          >>> battery information (still in the dock) I get says:
                          >>>> Charging Voltage 33.6 V
                          >>>> Battery Voltage 25.7V & 9.6V
                          >>>>
                          >>>> Is the information under battery voltage giving the individual battery
                          >>> voltages? I haven't found anywhere on this forum where there are two
                          >>> numbers
                          >>> under battery voltage.
                          >>>> Just hoping someone could give me some advice on how to proceed....
                          >>>>
                          >>>> Thanks,
                          >>>> Mike
                          >>>>
                          >>>> [Non-text portions of this message have been removed]
                          >>>>
                          >>>>
                          >>>>
                          >>>>
                          >>>> ________________________________
                          >>>> NOTICE: The information in this electronic mail transmission is intended
                          >>> by CoralTree Systems Ltd for the use of the named individuals or entity to
                          >>> which it is directed and may contain information that is privileged or
                          >>> otherwise confidential. If you have received this electronic mail
                          >>> transmission in error, please delete it from your system without copying or
                          >>> forwarding it, and notify the sender of the error by reply email or by
                          >>> telephone, so that the sender's address records can be corrected.
                          >>>>
                          >>>>
                          >>>> ----------------------------------------------------------
                          >>>>
                          >>>>
                          >>>> CoralTree Systems Limited
                          >>>> 25 Barnes Wallis Road
                          >>>> Segensworth East, Fareham
                          >>>> PO15 5TT
                          >>>>
                          >>>> Company Registration Number 5021022.
                          >>>> Registered Office:
                          >>>> 12-14 Carlton Place
                          >>>> Southampton, UK
                          >>>> SO15 2EA
                          >>>> VAT Registration Number 834 1020 74.
                          >>>>
                          >>>>
                          >>>> [Non-text portions of this message have been removed]
                          >>>>
                          >>> [Non-text portions of this message have been removed]
                          >>>
                          >>>
                          >>>
                          >>
                          >> [Non-text portions of this message have been removed]
                          >>
                          >
                          >
                          >
                          > ------------------------------------
                          >
                          > Yahoo! Groups Links
                          >
                          >
                          >
                          >
                        • Kevin Turner
                          I was puzzled by that until I realised you meant dew :) From: RoboMower@yahoogroups.com [mailto:RoboMower@yahoogroups.com] On Behalf Of rann_georgia Sent: 23
                          Message 12 of 24 , Jul 23, 2013
                            I was puzzled by that until I realised you meant "dew" :)

                            From: RoboMower@yahoogroups.com [mailto:RoboMower@yahoogroups.com] On Behalf Of rann_georgia
                            Sent: 23 July 2013 19:59
                            To: RoboMower@yahoogroups.com
                            Subject: [RoboMower] Re: Rl2000 Batteries?



                            the only problem that I see running it at night is doo. The grass could be wet and that creates more resistance. More resistance takes more power meaning shorter mowing times.

                            My mower has glided right over power cords, hoses and such. The major problem I have is making sure the car is not in the zone as it will get stuck under it.

                            BTW, I do like the idea someone else had of using a knife sharpener on the blades for a touch up.

                            --- In RoboMower@yahoogroups.com<mailto:RoboMower%40yahoogroups.com>, Ben <ben.jordan@...<mailto:ben.jordan@...>> wrote:
                            >
                            > "You can use automatic, at night when the kids are asleep.
                            >
                            > The mower doesn't care if it's dark and it's not very loud.
                            >
                            > Dan"
                            >
                            > It's not the kids or pets I worry about..... they can move! It's the toys,
                            > garden hose, tree branches, and who knows what else was left out there this
                            > time that I worry about.
                            >
                            >
                            > On Tue, Jul 23, 2013 at 12:55 PM, Dan Barclay <Dan@...<mailto:Dan@...>>wrote:
                            >
                            > > **
                            > >
                            > >
                            > > You can use automatic, at night when the kids are asleep.
                            > >
                            > > The mower doesn't care if it's dark and it's not very loud.
                            > >
                            > > Dan
                            > >
                            > >
                            > > From: RoboMower@yahoogroups.com<mailto:RoboMower%40yahoogroups.com> [mailto:RoboMower@yahoogroups.com<mailto:RoboMower%40yahoogroups.com>] On
                            > > Behalf
                            > > Of mikey0426
                            > > Sent: Saturday, July 20, 2013 6:25 PM
                            > > To: RoboMower@yahoogroups.com<mailto:RoboMower%40yahoogroups.com>
                            > >
                            > > Subject: [RoboMower] Re: Rl2000 Batteries?
                            > >
                            > > Yes, I am only doing manual depart because I have 3 little kids running
                            > > around in the back, but I have used max. The first time, it only cut about
                            > > half the yard before returning. The second time, there were about 7 or 8
                            > > stripes. The base zone is only about 0.15ish acre.
                            > >
                            > > Thanks
                            > >
                            > > --- In RoboMower@yahoogroups.com<mailto:RoboMower%40yahoogroups.com> <mailto:RoboMower%40yahoogroups.com> ,
                            > >
                            > > Kevin Turner <kevin.turner@> wrote:
                            > > >
                            > > > Mine says
                            > > > 26.3v 9.3v
                            > > >
                            > > > No idea what that tells me with regard to how good or bad it is .
                            > > >
                            > > > Silly question, but you have set your program to "max" haven't you?
                            > > >
                            > > > Sent from my iPad
                            > > >
                            > > > On 20 Jul 2013, at 20:18, "Kevin Turner" <kevin.turner@
                            <mailto:kevin.turner@%0b>> > <mailto:kevin.turner@%3cmailto:kevin.turner@>
                            > >
                            > > <mailto:kevin.turner@>> wrote:
                            > > >
                            > > > I have owned an RL2000 for just over a year. On the program's where it s
                            > > set to cut for the MAX amount of time, it will keep going for well over 4
                            > > hours easily.
                            > > >
                            > > > I have never checked the voltage during charging. I'll take a look.....
                            > > >
                            > > > Sent from my iPad
                            > > >
                            > > > On 20 Jul 2013, at 17:42, "Michael" <mikey0426@
                            > > <mailto:mikey0426@%3cmailto:mikey0426@> <mailto:mikey0426@>>
                            > > wrote:
                            > > >
                            > > >
                            > > >
                            > > > Hi there,
                            > > >
                            > > > So happy to find this group! Does anyone have experience with the rl2000
                            > > yet? I bought one last week, and it cuts great. Problem is, I have yet to
                            > > get longer than 1 hr 40 min before it returns to base to charge. I know it
                            > > should last longer than that! After sitting on the dock for 48 hours, the
                            > > battery information (still in the dock) I get says:
                            > > >
                            > > > Charging Voltage 33.6 V
                            > > > Battery Voltage 25.7V & 9.6V
                            > > >
                            > > > Is the information under battery voltage giving the individual battery
                            > > voltages? I haven't found anywhere on this forum where there are two
                            > > numbers
                            > > under battery voltage.
                            > > >
                            > > > Just hoping someone could give me some advice on how to proceed....
                            > > >
                            > > > Thanks,
                            > > > Mike
                            > > >
                            > > > [Non-text portions of this message have been removed]
                            > > >
                            > > >
                            > > >
                            > > >
                            > > > ________________________________
                            > > > NOTICE: The information in this electronic mail transmission is intended
                            > > by CoralTree Systems Ltd for the use of the named individuals or entity to
                            > > which it is directed and may contain information that is privileged or
                            > > otherwise confidential. If you have received this electronic mail
                            > > transmission in error, please delete it from your system without copying or
                            > > forwarding it, and notify the sender of the error by reply email or by
                            > > telephone, so that the sender's address records can be corrected.
                            > > >
                            > > >
                            > > >
                            > > > ----------------------------------------------------------
                            > > >
                            > > >
                            > > > CoralTree Systems Limited
                            > > > 25 Barnes Wallis Road
                            > > > Segensworth East, Fareham
                            > > > PO15 5TT
                            > > >
                            > > > Company Registration Number 5021022.
                            > > > Registered Office:
                            > > > 12-14 Carlton Place
                            > > > Southampton, UK
                            > > > SO15 2EA
                            > > > VAT Registration Number 834 1020 74.
                            > > >
                            > > >
                            > > > [Non-text portions of this message have been removed]
                            > > >
                            > >
                            > > [Non-text portions of this message have been removed]
                            > >
                            > >
                            > >
                            >
                            >
                            > [Non-text portions of this message have been removed]
                            >


                            ________________________________
                            NOTICE: The information in this electronic mail transmission is intended by CoralTree Systems Ltd for the use of the named individuals or entity to which it is directed and may contain information that is privileged or otherwise confidential. If you have received this electronic mail transmission in error, please delete it from your system without copying or forwarding it, and notify the sender of the error by reply email or by telephone, so that the sender's address records can be corrected.



                            --------------------------------------------------------------------------------


                            CoralTree Systems Limited
                            25 Barnes Wallis Road
                            Segensworth East, Fareham
                            PO15 5TT

                            Company Registration Number 5021022.
                            Registered Office:
                            12-14 Carlton Place
                            Southampton, UK
                            SO15 2EA
                            VAT Registration Number 834 1020 74.


                            [Non-text portions of this message have been removed]
                          • Danny Miller
                            If they re reading 11v when off the charger, then the charger s probably malfunctioning. 11v is dead . Well, it s the point where you recharge. Danny
                            Message 13 of 24 , Jul 23, 2013
                              If they're reading 11v when off the charger, then the charger's probably
                              malfunctioning.

                              11v is "dead". Well, it's the point where you recharge.

                              Danny

                              On 7/23/2013 1:43 PM, rann_georgia wrote:
                              > Bad batteries can and do work for shorter periods.
                              >
                              > Since it's new, I hate to tell you to pop that battery pack open and unshort the wires.
                              >
                              > There is a voltage meter that's about 70 bucks or so that can measure whether a battery is bad, not just the voltage. As far as I know, they do this on 12v batteries only. I'm a minus for Batteries Plus
                              > because they replaced the original battery with a cheaper model and have done so every year for the last three running.
                              >
                              > I'm still going with bad battery pack.
                              >
                              > You try a few unorthodox things. The man who runs Probotics is very knowledgeable and helpful. You might catch him on a slow day and he'll talk your ear off. You could try calling that dealership and I'm sure he's experienced almost everything related to these things.
                              >
                              >
                              >
                              >
                              > --- In RoboMower@yahoogroups.com, "mikey0426" <mikey0426@...> wrote:
                              >> Just bought it brand new, from Sams club online.
                              >>
                              >> I bought a cheap voltmeter, and pulled the power pack from the mower. Each battery read 11V(ish). The back of the power pack read around 23. Not really sure what to do next.....I suppose its possible that the dock is not providing adequate power, since these batteries are brand new......
                              >>
                              >> Thoughts?
                              >>
                              >> --- In RoboMower@yahoogroups.com, "rann_georgia" <southbound03@> wrote:
                              >>> You say you just bought it. Was it new or used?
                              >>>
                              >>> I'm going to go out on a limb and say you have a bad battery or both.
                              >>>
                              >>> If the battery pack is like the RL1000, it's two 12v batteries wired in series to get 24 volts. Once I wired mine wrong in parallel. The mower didn't like it and didn't run properly but it worked.
                              >>>
                              >>> I'd check the batteries by taking it to an auto parts store. They have a tester that will determine if you have a bad battery. But, usually, a bad battery will quickly shorten the life of the other.
                              >>>
                              >>> --- In RoboMower@yahoogroups.com, "mikey0426" <mikey0426@> wrote:
                              >>>> Yes, I am only doing manual depart because I have 3 little kids running around in the back, but I have used max. The first time, it only cut about half the yard before returning. The second time, there were about 7 or 8 stripes. The base zone is only about 0.15ish acre.
                              >>>>
                              >>>> Thanks
                              >>>>
                              >>>> --- In RoboMower@yahoogroups.com, Kevin Turner <kevin.turner@> wrote:
                              >>>>> Mine says
                              >>>>> 26.3v 9.3v
                              >>>>>
                              >>>>> No idea what that tells me with regard to how good or bad it is .
                              >>>>>
                              >>>>> Silly question, but you have set your program to "max" haven't you?
                              >>>>>
                              >>>>> Sent from my iPad
                              >>>>>
                              >>>>> On 20 Jul 2013, at 20:18, "Kevin Turner" <kevin.turner@<mailto:kevin.turner@>> wrote:
                              >>>>>
                              >>>>> I have owned an RL2000 for just over a year. On the program's where it s set to cut for the MAX amount of time, it will keep going for well over 4 hours easily.
                              >>>>>
                              >>>>> I have never checked the voltage during charging. I'll take a look.....
                              >>>>>
                              >>>>> Sent from my iPad
                              >>>>>
                              >>>>> On 20 Jul 2013, at 17:42, "Michael" <mikey0426@<mailto:mikey0426@>> wrote:
                              >>>>>
                              >>>>>
                              >>>>>
                              >>>>> Hi there,
                              >>>>>
                              >>>>> So happy to find this group! Does anyone have experience with the rl2000 yet? I bought one last week, and it cuts great. Problem is, I have yet to get longer than 1 hr 40 min before it returns to base to charge. I know it should last longer than that! After sitting on the dock for 48 hours, the battery information (still in the dock) I get says:
                              >>>>>
                              >>>>> Charging Voltage 33.6 V
                              >>>>> Battery Voltage 25.7V & 9.6V
                              >>>>>
                              >>>>> Is the information under battery voltage giving the individual battery voltages? I haven't found anywhere on this forum where there are two numbers under battery voltage.
                              >>>>>
                              >>>>> Just hoping someone could give me some advice on how to proceed....
                              >>>>>
                              >>>>> Thanks,
                              >>>>> Mike
                              >>>>>
                              >>>>> [Non-text portions of this message have been removed]
                              >>>>>
                              >>>>>
                              >>>>>
                              >>>>>
                              >>>>> ________________________________
                              >>>>> NOTICE: The information in this electronic mail transmission is intended by CoralTree Systems Ltd for the use of the named individuals or entity to which it is directed and may contain information that is privileged or otherwise confidential. If you have received this electronic mail transmission in error, please delete it from your system without copying or forwarding it, and notify the sender of the error by reply email or by telephone, so that the sender's address records can be corrected.
                              >>>>>
                              >>>>>
                              >>>>>
                              >>>>> --------------------------------------------------------------------------------
                              >>>>>
                              >>>>>
                              >>>>> CoralTree Systems Limited
                              >>>>> 25 Barnes Wallis Road
                              >>>>> Segensworth East, Fareham
                              >>>>> PO15 5TT
                              >>>>>
                              >>>>> Company Registration Number 5021022.
                              >>>>> Registered Office:
                              >>>>> 12-14 Carlton Place
                              >>>>> Southampton, UK
                              >>>>> SO15 2EA
                              >>>>> VAT Registration Number 834 1020 74.
                              >>>>>
                              >>>>>
                              >>>>> [Non-text portions of this message have been removed]
                              >>>>>
                              >
                              >
                              >
                              > ------------------------------------
                              >
                              > Yahoo! Groups Links
                              >
                              >
                              >
                              >
                            • Dan Barclay
                              Yes, if you mow too late you can get wet grass at times. But, you can also get wet grass from rain. There are times of the year that we get dew right away,
                              Message 14 of 24 , Jul 23, 2013
                                Yes, if you mow too late you can get wet grass at times. But, you can also
                                get wet grass from rain.



                                There are times of the year that we get dew right away, but not that often.
                                Mowing at 10p generally hasn't been a problem. My "wet mowing" has mostly
                                occurred during/after rain.



                                Concur about the toys. Hoses haven't been a problem except when one crosses
                                over itself making a short section stick up. If it's flat the mower will
                                just go over it but if it has a piece sticking up it'll sure nick a hole in
                                it.



                                Dan



                                From: RoboMower@yahoogroups.com [mailto:RoboMower@yahoogroups.com] On Behalf
                                Of Danny Miller
                                Sent: Tuesday, July 23, 2013 2:13 PM
                                To: RoboMower@yahoogroups.com
                                Subject: Re: [RoboMower] Re: Rl2000 Batteries?





                                Not all weather conditions produce dew on every night.

                                But I'll say right now, wet grass DOES suck. Not just because of
                                resistance, it can cake up inside the blade wells and it'll mostly stop
                                cutting when that happens.

                                Danny

                                On 7/23/2013 1:58 PM, rann_georgia wrote:
                                > the only problem that I see running it at night is doo. The grass could be
                                wet and that creates more resistance. More resistance takes more power
                                meaning shorter mowing times.
                                >
                                > My mower has glided right over power cords, hoses and such. The major
                                problem I have is making sure the car is not in the zone as it will get
                                stuck under it.
                                >
                                > BTW, I do like the idea someone else had of using a knife sharpener on the
                                blades for a touch up.
                                >
                                > --- In RoboMower@yahoogroups.com <mailto:RoboMower%40yahoogroups.com> ,
                                Ben <ben.jordan@...> wrote:
                                >> "You can use automatic, at night when the kids are asleep.
                                >>
                                >> The mower doesn't care if it's dark and it's not very loud.
                                >>
                                >> Dan"
                                >>
                                >> It's not the kids or pets I worry about..... they can move! It's the
                                toys,
                                >> garden hose, tree branches, and who knows what else was left out there
                                this
                                >> time that I worry about.
                                >>
                                >>
                                >> On Tue, Jul 23, 2013 at 12:55 PM, Dan Barclay <Dan@...>wrote:
                                >>
                                >>> **
                                >>>
                                >>>
                                >>> You can use automatic, at night when the kids are asleep.
                                >>>
                                >>> The mower doesn't care if it's dark and it's not very loud.
                                >>>
                                >>> Dan
                                >>>
                                >>>
                                >>> From: RoboMower@yahoogroups.com <mailto:RoboMower%40yahoogroups.com>
                                [mailto:RoboMower@yahoogroups.com <mailto:RoboMower%40yahoogroups.com> ] On
                                >>> Behalf
                                >>> Of mikey0426
                                >>> Sent: Saturday, July 20, 2013 6:25 PM
                                >>> To: RoboMower@yahoogroups.com <mailto:RoboMower%40yahoogroups.com>
                                >>>
                                >>> Subject: [RoboMower] Re: Rl2000 Batteries?
                                >>>
                                >>> Yes, I am only doing manual depart because I have 3 little kids running
                                >>> around in the back, but I have used max. The first time, it only cut
                                about
                                >>> half the yard before returning. The second time, there were about 7 or 8
                                >>> stripes. The base zone is only about 0.15ish acre.
                                >>>
                                >>> Thanks
                                >>>
                                >>> --- In RoboMower@yahoogroups.com <mailto:RoboMower%40yahoogroups.com>
                                <mailto:RoboMower%40yahoogroups.com> ,
                                >>>
                                >>> Kevin Turner <kevin.turner@> wrote:
                                >>>> Mine says
                                >>>> 26.3v 9.3v
                                >>>>
                                >>>> No idea what that tells me with regard to how good or bad it is .
                                >>>>
                                >>>> Silly question, but you have set your program to "max" haven't you?
                                >>>>
                                >>>> Sent from my iPad
                                >>>>
                                >>>> On 20 Jul 2013, at 20:18, "Kevin Turner" <kevin.turner@
                                <mailto:kevin.turner@%0b>
                                >>> <mailto:kevin.turner@%3cmailto:kevin.turner@>
                                >>>
                                >>> <mailto:kevin.turner@>> wrote:
                                >>>> I have owned an RL2000 for just over a year. On the program's where it
                                s
                                >>> set to cut for the MAX amount of time, it will keep going for well over
                                4
                                >>> hours easily.
                                >>>> I have never checked the voltage during charging. I'll take a look.....
                                >>>>
                                >>>> Sent from my iPad
                                >>>>
                                >>>> On 20 Jul 2013, at 17:42, "Michael" <mikey0426@
                                >>> <mailto:mikey0426@%3cmailto:mikey0426@> <mailto:mikey0426@>>
                                >>> wrote:
                                >>>>
                                >>>>
                                >>>> Hi there,
                                >>>>
                                >>>> So happy to find this group! Does anyone have experience with the
                                rl2000
                                >>> yet? I bought one last week, and it cuts great. Problem is, I have yet
                                to
                                >>> get longer than 1 hr 40 min before it returns to base to charge. I know
                                it
                                >>> should last longer than that! After sitting on the dock for 48 hours,
                                the
                                >>> battery information (still in the dock) I get says:
                                >>>> Charging Voltage 33.6 V
                                >>>> Battery Voltage 25.7V & 9.6V
                                >>>>
                                >>>> Is the information under battery voltage giving the individual battery
                                >>> voltages? I haven't found anywhere on this forum where there are two
                                >>> numbers
                                >>> under battery voltage.
                                >>>> Just hoping someone could give me some advice on how to proceed....
                                >>>>
                                >>>> Thanks,
                                >>>> Mike
                                >>>>
                                >>>> [Non-text portions of this message have been removed]
                                >>>>
                                >>>>
                                >>>>
                                >>>>
                                >>>> ________________________________
                                >>>> NOTICE: The information in this electronic mail transmission is
                                intended
                                >>> by CoralTree Systems Ltd for the use of the named individuals or entity
                                to
                                >>> which it is directed and may contain information that is privileged or
                                >>> otherwise confidential. If you have received this electronic mail
                                >>> transmission in error, please delete it from your system without copying
                                or
                                >>> forwarding it, and notify the sender of the error by reply email or by
                                >>> telephone, so that the sender's address records can be corrected.
                                >>>>
                                >>>>
                                >>>> ----------------------------------------------------------
                                >>>>
                                >>>>
                                >>>> CoralTree Systems Limited
                                >>>> 25 Barnes Wallis Road
                                >>>> Segensworth East, Fareham
                                >>>> PO15 5TT
                                >>>>
                                >>>> Company Registration Number 5021022.
                                >>>> Registered Office:
                                >>>> 12-14 Carlton Place
                                >>>> Southampton, UK
                                >>>> SO15 2EA
                                >>>> VAT Registration Number 834 1020 74.
                                >>>>
                                >>>>
                                >>>> [Non-text portions of this message have been removed]
                                >>>>
                                >>> [Non-text portions of this message have been removed]
                                >>>
                                >>>
                                >>>
                                >>
                                >> [Non-text portions of this message have been removed]
                                >>
                                >
                                >
                                >
                                > ------------------------------------
                                >
                                > Yahoo! Groups Links
                                >
                                >
                                >
                                >





                                [Non-text portions of this message have been removed]
                              • rann_georgia
                                I am a notoriously bad speller. Another tip may have been from the same person and that was to spray the wells with cooking spray to help prevent caking up of
                                Message 15 of 24 , Jul 23, 2013
                                  I am a notoriously bad speller.

                                  Another tip may have been from the same person and that was to spray the wells with cooking spray to help prevent caking up of grass.



                                  --- In RoboMower@yahoogroups.com, Kevin Turner <kevin.turner@...> wrote:
                                  >
                                  > I was puzzled by that until I realised you meant "dew" :)
                                  >
                                  > From: RoboMower@yahoogroups.com [mailto:RoboMower@yahoogroups.com] On Behalf Of rann_georgia
                                  > Sent: 23 July 2013 19:59
                                  > To: RoboMower@yahoogroups.com
                                  > Subject: [RoboMower] Re: Rl2000 Batteries?
                                  >
                                  >
                                  >
                                  > the only problem that I see running it at night is doo. The grass could be wet and that creates more resistance. More resistance takes more power meaning shorter mowing times.
                                  >
                                  > My mower has glided right over power cords, hoses and such. The major problem I have is making sure the car is not in the zone as it will get stuck under it.
                                  >
                                  > BTW, I do like the idea someone else had of using a knife sharpener on the blades for a touch up.
                                  >
                                  > --- In RoboMower@yahoogroups.com<mailto:RoboMower%40yahoogroups.com>, Ben <ben.jordan@<mailto:ben.jordan@>> wrote:
                                  > >
                                  > > "You can use automatic, at night when the kids are asleep.
                                  > >
                                  > > The mower doesn't care if it's dark and it's not very loud.
                                  > >
                                  > > Dan"
                                  > >
                                  > > It's not the kids or pets I worry about..... they can move! It's the toys,
                                  > > garden hose, tree branches, and who knows what else was left out there this
                                  > > time that I worry about.
                                  > >
                                  > >
                                  > > On Tue, Jul 23, 2013 at 12:55 PM, Dan Barclay <Dan@<mailto:Dan@>>wrote:
                                  > >
                                  > > > **
                                  > > >
                                  > > >
                                  > > > You can use automatic, at night when the kids are asleep.
                                  > > >
                                  > > > The mower doesn't care if it's dark and it's not very loud.
                                  > > >
                                  > > > Dan
                                  > > >
                                  > > >
                                  > > > From: RoboMower@yahoogroups.com<mailto:RoboMower%40yahoogroups.com> [mailto:RoboMower@yahoogroups.com<mailto:RoboMower%40yahoogroups.com>] On
                                  > > > Behalf
                                  > > > Of mikey0426
                                  > > > Sent: Saturday, July 20, 2013 6:25 PM
                                  > > > To: RoboMower@yahoogroups.com<mailto:RoboMower%40yahoogroups.com>
                                  > > >
                                  > > > Subject: [RoboMower] Re: Rl2000 Batteries?
                                  > > >
                                  > > > Yes, I am only doing manual depart because I have 3 little kids running
                                  > > > around in the back, but I have used max. The first time, it only cut about
                                  > > > half the yard before returning. The second time, there were about 7 or 8
                                  > > > stripes. The base zone is only about 0.15ish acre.
                                  > > >
                                  > > > Thanks
                                  > > >
                                  > > > --- In RoboMower@yahoogroups.com<mailto:RoboMower%40yahoogroups.com> <mailto:RoboMower%40yahoogroups.com> ,
                                  > > >
                                  > > > Kevin Turner <kevin.turner@> wrote:
                                  > > > >
                                  > > > > Mine says
                                  > > > > 26.3v 9.3v
                                  > > > >
                                  > > > > No idea what that tells me with regard to how good or bad it is .
                                  > > > >
                                  > > > > Silly question, but you have set your program to "max" haven't you?
                                  > > > >
                                  > > > > Sent from my iPad
                                  > > > >
                                  > > > > On 20 Jul 2013, at 20:18, "Kevin Turner" <kevin.turner@
                                  > <mailto:kevin.turner@%0b>> > <mailto:kevin.turner@%3cmailto:kevin.turner@>
                                  > > >
                                  > > > <mailto:kevin.turner@>> wrote:
                                  > > > >
                                  > > > > I have owned an RL2000 for just over a year. On the program's where it s
                                  > > > set to cut for the MAX amount of time, it will keep going for well over 4
                                  > > > hours easily.
                                  > > > >
                                  > > > > I have never checked the voltage during charging. I'll take a look.....
                                  > > > >
                                  > > > > Sent from my iPad
                                  > > > >
                                  > > > > On 20 Jul 2013, at 17:42, "Michael" <mikey0426@
                                  > > > <mailto:mikey0426@%3cmailto:mikey0426@> <mailto:mikey0426@>>
                                  > > > wrote:
                                  > > > >
                                  > > > >
                                  > > > >
                                  > > > > Hi there,
                                  > > > >
                                  > > > > So happy to find this group! Does anyone have experience with the rl2000
                                  > > > yet? I bought one last week, and it cuts great. Problem is, I have yet to
                                  > > > get longer than 1 hr 40 min before it returns to base to charge. I know it
                                  > > > should last longer than that! After sitting on the dock for 48 hours, the
                                  > > > battery information (still in the dock) I get says:
                                  > > > >
                                  > > > > Charging Voltage 33.6 V
                                  > > > > Battery Voltage 25.7V & 9.6V
                                  > > > >
                                  > > > > Is the information under battery voltage giving the individual battery
                                  > > > voltages? I haven't found anywhere on this forum where there are two
                                  > > > numbers
                                  > > > under battery voltage.
                                  > > > >
                                  > > > > Just hoping someone could give me some advice on how to proceed....
                                  > > > >
                                  > > > > Thanks,
                                  > > > > Mike
                                  > > > >
                                  > > > > [Non-text portions of this message have been removed]
                                  > > > >
                                  > > > >
                                  > > > >
                                  > > > >
                                  > > > > ________________________________
                                  > > > > NOTICE: The information in this electronic mail transmission is intended
                                  > > > by CoralTree Systems Ltd for the use of the named individuals or entity to
                                  > > > which it is directed and may contain information that is privileged or
                                  > > > otherwise confidential. If you have received this electronic mail
                                  > > > transmission in error, please delete it from your system without copying or
                                  > > > forwarding it, and notify the sender of the error by reply email or by
                                  > > > telephone, so that the sender's address records can be corrected.
                                  > > > >
                                  > > > >
                                  > > > >
                                  > > > > ----------------------------------------------------------
                                  > > > >
                                  > > > >
                                  > > > > CoralTree Systems Limited
                                  > > > > 25 Barnes Wallis Road
                                  > > > > Segensworth East, Fareham
                                  > > > > PO15 5TT
                                  > > > >
                                  > > > > Company Registration Number 5021022.
                                  > > > > Registered Office:
                                  > > > > 12-14 Carlton Place
                                  > > > > Southampton, UK
                                  > > > > SO15 2EA
                                  > > > > VAT Registration Number 834 1020 74.
                                  > > > >
                                  > > > >
                                  > > > > [Non-text portions of this message have been removed]
                                  > > > >
                                  > > >
                                  > > > [Non-text portions of this message have been removed]
                                  > > >
                                  > > >
                                  > > >
                                  > >
                                  > >
                                  > > [Non-text portions of this message have been removed]
                                  > >
                                  >
                                  >
                                  > ________________________________
                                  > NOTICE: The information in this electronic mail transmission is intended by CoralTree Systems Ltd for the use of the named individuals or entity to which it is directed and may contain information that is privileged or otherwise confidential. If you have received this electronic mail transmission in error, please delete it from your system without copying or forwarding it, and notify the sender of the error by reply email or by telephone, so that the sender's address records can be corrected.
                                  >
                                  >
                                  >
                                  > --------------------------------------------------------------------------------
                                  >
                                  >
                                  > CoralTree Systems Limited
                                  > 25 Barnes Wallis Road
                                  > Segensworth East, Fareham
                                  > PO15 5TT
                                  >
                                  > Company Registration Number 5021022.
                                  > Registered Office:
                                  > 12-14 Carlton Place
                                  > Southampton, UK
                                  > SO15 2EA
                                  > VAT Registration Number 834 1020 74.
                                  >
                                  >
                                  > [Non-text portions of this message have been removed]
                                  >
                                • mikey0426
                                  Ok, sorry one more battery question. If the charger is bad, what is the best way to tell? The information says charging voltage 33.6V, but is that a
                                  Message 16 of 24 , Jul 23, 2013
                                    Ok, sorry one more battery question. If the charger is bad, what is the best way to tell? The information says charging voltage 33.6V, but is that a measurement or just a default when it's plugged in?

                                    Also, assuming the mower has enough battery to fully cut my back yard, it has left small triangles about 2 feet on one side) in about 6 or 7 places in the yard. Are there any settings that I can try to remedy that? Tired of cutting the missed spots by hand. The yard is not big, but there are a couple juts and a play set to bounce off of....perhaps it's just confused?

                                    Thanks for all the great help!
                                    Mike

                                    --- In RoboMower@yahoogroups.com, "rann_georgia" <southbound03@...> wrote:
                                    >
                                    > I am a notoriously bad speller.
                                    >
                                    > Another tip may have been from the same person and that was to spray the wells with cooking spray to help prevent caking up of grass.
                                    >
                                    >
                                    >
                                    > --- In RoboMower@yahoogroups.com, Kevin Turner <kevin.turner@> wrote:
                                    > >
                                    > > I was puzzled by that until I realised you meant "dew" :)
                                    > >
                                    > > From: RoboMower@yahoogroups.com [mailto:RoboMower@yahoogroups.com] On Behalf Of rann_georgia
                                    > > Sent: 23 July 2013 19:59
                                    > > To: RoboMower@yahoogroups.com
                                    > > Subject: [RoboMower] Re: Rl2000 Batteries?
                                    > >
                                    > >
                                    > >
                                    > > the only problem that I see running it at night is doo. The grass could be wet and that creates more resistance. More resistance takes more power meaning shorter mowing times.
                                    > >
                                    > > My mower has glided right over power cords, hoses and such. The major problem I have is making sure the car is not in the zone as it will get stuck under it.
                                    > >
                                    > > BTW, I do like the idea someone else had of using a knife sharpener on the blades for a touch up.
                                    > >
                                    > > --- In RoboMower@yahoogroups.com<mailto:RoboMower%40yahoogroups.com>, Ben <ben.jordan@<mailto:ben.jordan@>> wrote:
                                    > > >
                                    > > > "You can use automatic, at night when the kids are asleep.
                                    > > >
                                    > > > The mower doesn't care if it's dark and it's not very loud.
                                    > > >
                                    > > > Dan"
                                    > > >
                                    > > > It's not the kids or pets I worry about..... they can move! It's the toys,
                                    > > > garden hose, tree branches, and who knows what else was left out there this
                                    > > > time that I worry about.
                                    > > >
                                    > > >
                                    > > > On Tue, Jul 23, 2013 at 12:55 PM, Dan Barclay <Dan@<mailto:Dan@>>wrote:
                                    > > >
                                    > > > > **
                                    > > > >
                                    > > > >
                                    > > > > You can use automatic, at night when the kids are asleep.
                                    > > > >
                                    > > > > The mower doesn't care if it's dark and it's not very loud.
                                    > > > >
                                    > > > > Dan
                                    > > > >
                                    > > > >
                                    > > > > From: RoboMower@yahoogroups.com<mailto:RoboMower%40yahoogroups.com> [mailto:RoboMower@yahoogroups.com<mailto:RoboMower%40yahoogroups.com>] On
                                    > > > > Behalf
                                    > > > > Of mikey0426
                                    > > > > Sent: Saturday, July 20, 2013 6:25 PM
                                    > > > > To: RoboMower@yahoogroups.com<mailto:RoboMower%40yahoogroups.com>
                                    > > > >
                                    > > > > Subject: [RoboMower] Re: Rl2000 Batteries?
                                    > > > >
                                    > > > > Yes, I am only doing manual depart because I have 3 little kids running
                                    > > > > around in the back, but I have used max. The first time, it only cut about
                                    > > > > half the yard before returning. The second time, there were about 7 or 8
                                    > > > > stripes. The base zone is only about 0.15ish acre.
                                    > > > >
                                    > > > > Thanks
                                    > > > >
                                    > > > > --- In RoboMower@yahoogroups.com<mailto:RoboMower%40yahoogroups.com> <mailto:RoboMower%40yahoogroups.com> ,
                                    > > > >
                                    > > > > Kevin Turner <kevin.turner@> wrote:
                                    > > > > >
                                    > > > > > Mine says
                                    > > > > > 26.3v 9.3v
                                    > > > > >
                                    > > > > > No idea what that tells me with regard to how good or bad it is .
                                    > > > > >
                                    > > > > > Silly question, but you have set your program to "max" haven't you?
                                    > > > > >
                                    > > > > > Sent from my iPad
                                    > > > > >
                                    > > > > > On 20 Jul 2013, at 20:18, "Kevin Turner" <kevin.turner@
                                    > > <mailto:kevin.turner@%0b>> > <mailto:kevin.turner@%3cmailto:kevin.turner@>
                                    > > > >
                                    > > > > <mailto:kevin.turner@>> wrote:
                                    > > > > >
                                    > > > > > I have owned an RL2000 for just over a year. On the program's where it s
                                    > > > > set to cut for the MAX amount of time, it will keep going for well over 4
                                    > > > > hours easily.
                                    > > > > >
                                    > > > > > I have never checked the voltage during charging. I'll take a look.....
                                    > > > > >
                                    > > > > > Sent from my iPad
                                    > > > > >
                                    > > > > > On 20 Jul 2013, at 17:42, "Michael" <mikey0426@
                                    > > > > <mailto:mikey0426@%3cmailto:mikey0426@> <mailto:mikey0426@>>
                                    > > > > wrote:
                                    > > > > >
                                    > > > > >
                                    > > > > >
                                    > > > > > Hi there,
                                    > > > > >
                                    > > > > > So happy to find this group! Does anyone have experience with the rl2000
                                    > > > > yet? I bought one last week, and it cuts great. Problem is, I have yet to
                                    > > > > get longer than 1 hr 40 min before it returns to base to charge. I know it
                                    > > > > should last longer than that! After sitting on the dock for 48 hours, the
                                    > > > > battery information (still in the dock) I get says:
                                    > > > > >
                                    > > > > > Charging Voltage 33.6 V
                                    > > > > > Battery Voltage 25.7V & 9.6V
                                    > > > > >
                                    > > > > > Is the information under battery voltage giving the individual battery
                                    > > > > voltages? I haven't found anywhere on this forum where there are two
                                    > > > > numbers
                                    > > > > under battery voltage.
                                    > > > > >
                                    > > > > > Just hoping someone could give me some advice on how to proceed....
                                    > > > > >
                                    > > > > > Thanks,
                                    > > > > > Mike
                                    > > > > >
                                    > > > > > [Non-text portions of this message have been removed]
                                    > > > > >
                                    > > > > >
                                    > > > > >
                                    > > > > >
                                    > > > > > ________________________________
                                    > > > > > NOTICE: The information in this electronic mail transmission is intended
                                    > > > > by CoralTree Systems Ltd for the use of the named individuals or entity to
                                    > > > > which it is directed and may contain information that is privileged or
                                    > > > > otherwise confidential. If you have received this electronic mail
                                    > > > > transmission in error, please delete it from your system without copying or
                                    > > > > forwarding it, and notify the sender of the error by reply email or by
                                    > > > > telephone, so that the sender's address records can be corrected.
                                    > > > > >
                                    > > > > >
                                    > > > > >
                                    > > > > > ----------------------------------------------------------
                                    > > > > >
                                    > > > > >
                                    > > > > > CoralTree Systems Limited
                                    > > > > > 25 Barnes Wallis Road
                                    > > > > > Segensworth East, Fareham
                                    > > > > > PO15 5TT
                                    > > > > >
                                    > > > > > Company Registration Number 5021022.
                                    > > > > > Registered Office:
                                    > > > > > 12-14 Carlton Place
                                    > > > > > Southampton, UK
                                    > > > > > SO15 2EA
                                    > > > > > VAT Registration Number 834 1020 74.
                                    > > > > >
                                    > > > > >
                                    > > > > > [Non-text portions of this message have been removed]
                                    > > > > >
                                    > > > >
                                    > > > > [Non-text portions of this message have been removed]
                                    > > > >
                                    > > > >
                                    > > > >
                                    > > >
                                    > > >
                                    > > > [Non-text portions of this message have been removed]
                                    > > >
                                    > >
                                    > >
                                    > > ________________________________
                                    > > NOTICE: The information in this electronic mail transmission is intended by CoralTree Systems Ltd for the use of the named individuals or entity to which it is directed and may contain information that is privileged or otherwise confidential. If you have received this electronic mail transmission in error, please delete it from your system without copying or forwarding it, and notify the sender of the error by reply email or by telephone, so that the sender's address records can be corrected.
                                    > >
                                    > >
                                    > >
                                    > > --------------------------------------------------------------------------------
                                    > >
                                    > >
                                    > > CoralTree Systems Limited
                                    > > 25 Barnes Wallis Road
                                    > > Segensworth East, Fareham
                                    > > PO15 5TT
                                    > >
                                    > > Company Registration Number 5021022.
                                    > > Registered Office:
                                    > > 12-14 Carlton Place
                                    > > Southampton, UK
                                    > > SO15 2EA
                                    > > VAT Registration Number 834 1020 74.
                                    > >
                                    > >
                                    > > [Non-text portions of this message have been removed]
                                    > >
                                    >
                                  • gary burns
                                    I have fast charger for robomower batteries.  Its new and will sell for half of what they sell for on amazon,  I also have green stakes for sell and boxes of
                                    Message 17 of 24 , Jul 23, 2013
                                      I have fast charger for robomower batteries.  Its new and will sell for half of what they sell for on amazon,  I also have green stakes for sell and boxes of 500 foot per wire.
                                       
                                      812 946 2011


                                      ________________________________
                                      From: mikey0426 <mikey0426@...>
                                      To: RoboMower@yahoogroups.com
                                      Sent: Tuesday, July 23, 2013 7:02 PM
                                      Subject: [RoboMower] Re: Rl2000 Batteries?


                                       


                                      Ok, sorry one more battery question. If the charger is bad, what is the best way to tell? The information says charging voltage 33.6V, but is that a measurement or just a default when it's plugged in?

                                      Also, assuming the mower has enough battery to fully cut my back yard, it has left small triangles about 2 feet on one side) in about 6 or 7 places in the yard. Are there any settings that I can try to remedy that? Tired of cutting the missed spots by hand. The yard is not big, but there are a couple juts and a play set to bounce off of....perhaps it's just confused?

                                      Thanks for all the great help!
                                      Mike

                                      --- In mailto:RoboMower%40yahoogroups.com, "rann_georgia" <southbound03@...> wrote:
                                      >
                                      > I am a notoriously bad speller.
                                      >
                                      > Another tip may have been from the same person and that was to spray the wells with cooking spray to help prevent caking up of grass.
                                      >
                                      >
                                      >
                                      > --- In mailto:RoboMower%40yahoogroups.com, Kevin Turner <kevin.turner@> wrote:
                                      > >
                                      > > I was puzzled by that until I realised you meant "dew" :)
                                      > >
                                      > > From: mailto:RoboMower%40yahoogroups.com [mailto:mailto:RoboMower%40yahoogroups.com] On Behalf Of rann_georgia
                                      > > Sent: 23 July 2013 19:59
                                      > > To: mailto:RoboMower%40yahoogroups.com
                                      > > Subject: [RoboMower] Re: Rl2000 Batteries?
                                      > >
                                      > >
                                      > >
                                      > > the only problem that I see running it at night is doo. The grass could be wet and that creates more resistance. More resistance takes more power meaning shorter mowing times.
                                      > >
                                      > > My mower has glided right over power cords, hoses and such. The major problem I have is making sure the car is not in the zone as it will get stuck under it.
                                      > >
                                      > > BTW, I do like the idea someone else had of using a knife sharpener on the blades for a touch up.
                                      > >
                                      > > --- In mailto:RoboMower%40yahoogroups.com<mailto:RoboMower%40yahoogroups.com>, Ben <ben.jordan@<mailto:ben.jordan@>> wrote:
                                      > > >
                                      > > > "You can use automatic, at night when the kids are asleep.
                                      > > >
                                      > > > The mower doesn't care if it's dark and it's not very loud.
                                      > > >
                                      > > > Dan"
                                      > > >
                                      > > > It's not the kids or pets I worry about..... they can move! It's the toys,
                                      > > > garden hose, tree branches, and who knows what else was left out there this
                                      > > > time that I worry about.
                                      > > >
                                      > > >
                                      > > > On Tue, Jul 23, 2013 at 12:55 PM, Dan Barclay <Dan@<mailto:Dan@>>wrote:
                                      > > >
                                      > > > > **
                                      > > > >
                                      > > > >
                                      > > > > You can use automatic, at night when the kids are asleep.
                                      > > > >
                                      > > > > The mower doesn't care if it's dark and it's not very loud.
                                      > > > >
                                      > > > > Dan
                                      > > > >
                                      > > > >
                                      > > > > From: mailto:RoboMower%40yahoogroups.com<mailto:RoboMower%40yahoogroups.com> [mailto:mailto:RoboMower%40yahoogroups.com<mailto:RoboMower%40yahoogroups.com>] On
                                      > > > > Behalf
                                      > > > > Of mikey0426
                                      > > > > Sent: Saturday, July 20, 2013 6:25 PM
                                      > > > > To: mailto:RoboMower%40yahoogroups.com<mailto:RoboMower%40yahoogroups.com>
                                      > > > >
                                      > > > > Subject: [RoboMower] Re: Rl2000 Batteries?
                                      > > > >
                                      > > > > Yes, I am only doing manual depart because I have 3 little kids running
                                      > > > > around in the back, but I have used max. The first time, it only cut about
                                      > > > > half the yard before returning. The second time, there were about 7 or 8
                                      > > > > stripes. The base zone is only about 0.15ish acre.
                                      > > > >
                                      > > > > Thanks
                                      > > > >
                                      > > > > --- In mailto:RoboMower%40yahoogroups.com<mailto:RoboMower%40yahoogroups.com> <mailto:RoboMower%40yahoogroups.com> ,
                                      > > > >
                                      > > > > Kevin Turner <kevin.turner@> wrote:
                                      > > > > >
                                      > > > > > Mine says
                                      > > > > > 26.3v 9.3v
                                      > > > > >
                                      > > > > > No idea what that tells me with regard to how good or bad it is .
                                      > > > > >
                                      > > > > > Silly question, but you have set your program to "max" haven't you?
                                      > > > > >
                                      > > > > > Sent from my iPad
                                      > > > > >
                                      > > > > > On 20 Jul 2013, at 20:18, "Kevin Turner" <kevin.turner@
                                      > > <mailto:kevin.turner@%0b>> > <mailto:kevin.turner@%3cmailto:kevin.turner@>
                                      > > > >
                                      > > > > <mailto:kevin.turner@>> wrote:
                                      > > > > >
                                      > > > > > I have owned an RL2000 for just over a year. On the program's where it s
                                      > > > > set to cut for the MAX amount of time, it will keep going for well over 4
                                      > > > > hours easily.
                                      > > > > >
                                      > > > > > I have never checked the voltage during charging. I'll take a look.....
                                      > > > > >
                                      > > > > > Sent from my iPad
                                      > > > > >
                                      > > > > > On 20 Jul 2013, at 17:42, "Michael" <mikey0426@
                                      > > > > <mailto:mikey0426@%3cmailto:mikey0426@> <mailto:mikey0426@>>
                                      > > > > wrote:
                                      > > > > >
                                      > > > > >
                                      > > > > >
                                      > > > > > Hi there,
                                      > > > > >
                                      > > > > > So happy to find this group! Does anyone have experience with the rl2000
                                      > > > > yet? I bought one last week, and it cuts great. Problem is, I have yet to
                                      > > > > get longer than 1 hr 40 min before it returns to base to charge. I know it
                                      > > > > should last longer than that! After sitting on the dock for 48 hours, the
                                      > > > > battery information (still in the dock) I get says:
                                      > > > > >
                                      > > > > > Charging Voltage 33.6 V
                                      > > > > > Battery Voltage 25.7V & 9.6V
                                      > > > > >
                                      > > > > > Is the information under battery voltage giving the individual battery
                                      > > > > voltages? I haven't found anywhere on this forum where there are two
                                      > > > > numbers
                                      > > > > under battery voltage.
                                      > > > > >
                                      > > > > > Just hoping someone could give me some advice on how to proceed....
                                      > > > > >
                                      > > > > > Thanks,
                                      > > > > > Mike
                                      > > > > >
                                      > > > > > [Non-text portions of this message have been removed]
                                      > > > > >
                                      > > > > >
                                      > > > > >
                                      > > > > >
                                      > > > > > ________________________________
                                      > > > > > NOTICE: The information in this electronic mail transmission is intended
                                      > > > > by CoralTree Systems Ltd for the use of the named individuals or entity to
                                      > > > > which it is directed and may contain information that is privileged or
                                      > > > > otherwise confidential. If you have received this electronic mail
                                      > > > > transmission in error, please delete it from your system without copying or
                                      > > > > forwarding it, and notify the sender of the error by reply email or by
                                      > > > > telephone, so that the sender's address records can be corrected.
                                      > > > > >
                                      > > > > >
                                      > > > > >
                                      > > > > > ----------------------------------------------------------
                                      > > > > >
                                      > > > > >
                                      > > > > > CoralTree Systems Limited
                                      > > > > > 25 Barnes Wallis Road
                                      > > > > > Segensworth East, Fareham
                                      > > > > > PO15 5TT
                                      > > > > >
                                      > > > > > Company Registration Number 5021022.
                                      > > > > > Registered Office:
                                      > > > > > 12-14 Carlton Place
                                      > > > > > Southampton, UK
                                      > > > > > SO15 2EA
                                      > > > > > VAT Registration Number 834 1020 74.
                                      > > > > >
                                      > > > > >
                                      > > > > > [Non-text portions of this message have been removed]
                                      > > > > >
                                      > > > >
                                      > > > > [Non-text portions of this message have been removed]
                                      > > > >
                                      > > > >
                                      > > > >
                                      > > >
                                      > > >
                                      > > > [Non-text portions of this message have been removed]
                                      > > >
                                      > >
                                      > >
                                      > > ________________________________
                                      > > NOTICE: The information in this electronic mail transmission is intended by CoralTree Systems Ltd for the use of the named individuals or entity to which it is directed and may contain information that is privileged or otherwise confidential. If you have received this electronic mail transmission in error, please delete it from your system without copying or forwarding it, and notify the sender of the error by reply email or by telephone, so that the sender's address records can be corrected.
                                      > >
                                      > >
                                      > >
                                      > > ----------------------------------------------------------
                                      > >
                                      > >
                                      > > CoralTree Systems Limited
                                      > > 25 Barnes Wallis Road
                                      > > Segensworth East, Fareham
                                      > > PO15 5TT
                                      > >
                                      > > Company Registration Number 5021022.
                                      > > Registered Office:
                                      > > 12-14 Carlton Place
                                      > > Southampton, UK
                                      > > SO15 2EA
                                      > > VAT Registration Number 834 1020 74.
                                      > >
                                      > >
                                      > > [Non-text portions of this message have been removed]
                                      > >
                                      >




                                      [Non-text portions of this message have been removed]
                                    • Kevin Turner
                                      Assuming this places are within the perimeter it show mow them eventually....assuming it runs long enough. Try manually starting it around that area and see
                                      Message 18 of 24 , Jul 24, 2013
                                        Assuming this places are within the perimeter it show mow them eventually....assuming it runs long enough. Try manually starting it around that area and see if it is having difficulty entering that bit.

                                        From: RoboMower@yahoogroups.com [mailto:RoboMower@yahoogroups.com] On Behalf Of mikey0426
                                        Sent: 24 July 2013 03:03
                                        To: RoboMower@yahoogroups.com
                                        Subject: [RoboMower] Re: Rl2000 Batteries?



                                        Ok, sorry one more battery question. If the charger is bad, what is the best way to tell? The information says charging voltage 33.6V, but is that a measurement or just a default when it's plugged in?

                                        Also, assuming the mower has enough battery to fully cut my back yard, it has left small triangles about 2 feet on one side) in about 6 or 7 places in the yard. Are there any settings that I can try to remedy that? Tired of cutting the missed spots by hand. The yard is not big, but there are a couple juts and a play set to bounce off of....perhaps it's just confused?

                                        Thanks for all the great help!
                                        Mike

                                        --- In RoboMower@yahoogroups.com<mailto:RoboMower%40yahoogroups.com>, "rann_georgia" <southbound03@...<mailto:southbound03@...>> wrote:
                                        >
                                        > I am a notoriously bad speller.
                                        >
                                        > Another tip may have been from the same person and that was to spray the wells with cooking spray to help prevent caking up of grass.
                                        >
                                        >
                                        >
                                        > --- In RoboMower@yahoogroups.com<mailto:RoboMower%40yahoogroups.com>, Kevin Turner <kevin.turner@> wrote:
                                        > >
                                        > > I was puzzled by that until I realised you meant "dew" :)
                                        > >
                                        > > From: RoboMower@yahoogroups.com<mailto:RoboMower%40yahoogroups.com> [mailto:RoboMower@yahoogroups.com<mailto:RoboMower%40yahoogroups.com>] On Behalf Of rann_georgia
                                        > > Sent: 23 July 2013 19:59
                                        > > To: RoboMower@yahoogroups.com<mailto:RoboMower%40yahoogroups.com>
                                        > > Subject: [RoboMower] Re: Rl2000 Batteries?
                                        > >
                                        > >
                                        > >
                                        > > the only problem that I see running it at night is doo. The grass could be wet and that creates more resistance. More resistance takes more power meaning shorter mowing times.
                                        > >
                                        > > My mower has glided right over power cords, hoses and such. The major problem I have is making sure the car is not in the zone as it will get stuck under it.
                                        > >
                                        > > BTW, I do like the idea someone else had of using a knife sharpener on the blades for a touch up.
                                        > >
                                        > > --- In RoboMower@yahoogroups.com<mailto:RoboMower%40yahoogroups.com><mailto:RoboMower%40yahoogroups.com>, Ben <ben.jordan@<mailto:ben.jordan@<mailto:ben.jordan@%3cmailto:ben.jordan@>>> wrote:
                                        > > >
                                        > > > "You can use automatic, at night when the kids are asleep.
                                        > > >
                                        > > > The mower doesn't care if it's dark and it's not very loud.
                                        > > >
                                        > > > Dan"
                                        > > >
                                        > > > It's not the kids or pets I worry about..... they can move! It's the toys,
                                        > > > garden hose, tree branches, and who knows what else was left out there this
                                        > > > time that I worry about.
                                        > > >
                                        > > >
                                        > > > On Tue, Jul 23, 2013 at 12:55 PM, Dan Barclay <Dan@<mailto:Dan@>>wrote:
                                        > > >
                                        > > > > **
                                        > > > >
                                        > > > >
                                        > > > > You can use automatic, at night when the kids are asleep.
                                        > > > >
                                        > > > > The mower doesn't care if it's dark and it's not very loud.
                                        > > > >
                                        > > > > Dan
                                        > > > >
                                        > > > >
                                        > > > > From: RoboMower@yahoogroups.com<mailto:RoboMower%40yahoogroups.com><mailto:RoboMower%40yahoogroups.com> [mailto:RoboMower@yahoogroups.com<mailto:RoboMower%40yahoogroups.com><mailto:RoboMower%40yahoogroups.com>] On
                                        > > > > Behalf
                                        > > > > Of mikey0426
                                        > > > > Sent: Saturday, July 20, 2013 6:25 PM
                                        > > > > To: RoboMower@yahoogroups.com<mailto:RoboMower%40yahoogroups.com><mailto:RoboMower%40yahoogroups.com>
                                        > > > >
                                        > > > > Subject: [RoboMower] Re: Rl2000 Batteries?
                                        > > > >
                                        > > > > Yes, I am only doing manual depart because I have 3 little kids running
                                        > > > > around in the back, but I have used max. The first time, it only cut about
                                        > > > > half the yard before returning. The second time, there were about 7 or 8
                                        > > > > stripes. The base zone is only about 0.15ish acre.
                                        > > > >
                                        > > > > Thanks
                                        > > > >
                                        > > > > --- In RoboMower@yahoogroups.com<mailto:RoboMower%40yahoogroups.com><mailto:RoboMower%40yahoogroups.com> <mailto:RoboMower%40yahoogroups.com> ,
                                        > > > >
                                        > > > > Kevin Turner <kevin.turner@> wrote:
                                        > > > > >
                                        > > > > > Mine says
                                        > > > > > 26.3v 9.3v
                                        > > > > >
                                        > > > > > No idea what that tells me with regard to how good or bad it is .
                                        > > > > >
                                        > > > > > Silly question, but you have set your program to "max" haven't you?
                                        > > > > >
                                        > > > > > Sent from my iPad
                                        > > > > >
                                        > > > > > On 20 Jul 2013, at 20:18, "Kevin Turner" <kevin.turner@
                                        <mailto:kevin.turner@%0b>> > <mailto:kevin.turner@%0b>> > <mailto:kevin.turner@%3cmailto:kevin.turner@>
                                        > > > >
                                        > > > > <mailto:kevin.turner@>> wrote:
                                        > > > > >
                                        > > > > > I have owned an RL2000 for just over a year. On the program's where it s
                                        > > > > set to cut for the MAX amount of time, it will keep going for well over 4
                                        > > > > hours easily.
                                        > > > > >
                                        > > > > > I have never checked the voltage during charging. I'll take a look.....
                                        > > > > >
                                        > > > > > Sent from my iPad
                                        > > > > >
                                        > > > > > On 20 Jul 2013, at 17:42, "Michael" <mikey0426@
                                        > > > > <mailto:mikey0426@%3cmailto:mikey0426@> <mailto:mikey0426@>>
                                        > > > > wrote:
                                        > > > > >
                                        > > > > >
                                        > > > > >
                                        > > > > > Hi there,
                                        > > > > >
                                        > > > > > So happy to find this group! Does anyone have experience with the rl2000
                                        > > > > yet? I bought one last week, and it cuts great. Problem is, I have yet to
                                        > > > > get longer than 1 hr 40 min before it returns to base to charge. I know it
                                        > > > > should last longer than that! After sitting on the dock for 48 hours, the
                                        > > > > battery information (still in the dock) I get says:
                                        > > > > >
                                        > > > > > Charging Voltage 33.6 V
                                        > > > > > Battery Voltage 25.7V & 9.6V
                                        > > > > >
                                        > > > > > Is the information under battery voltage giving the individual battery
                                        > > > > voltages? I haven't found anywhere on this forum where there are two
                                        > > > > numbers
                                        > > > > under battery voltage.
                                        > > > > >
                                        > > > > > Just hoping someone could give me some advice on how to proceed....
                                        > > > > >
                                        > > > > > Thanks,
                                        > > > > > Mike
                                        > > > > >
                                        > > > > > [Non-text portions of this message have been removed]
                                        > > > > >
                                        > > > > >
                                        > > > > >
                                        > > > > >
                                        > > > > > ________________________________
                                        > > > > > NOTICE: The information in this electronic mail transmission is intended
                                        > > > > by CoralTree Systems Ltd for the use of the named individuals or entity to
                                        > > > > which it is directed and may contain information that is privileged or
                                        > > > > otherwise confidential. If you have received this electronic mail
                                        > > > > transmission in error, please delete it from your system without copying or
                                        > > > > forwarding it, and notify the sender of the error by reply email or by
                                        > > > > telephone, so that the sender's address records can be corrected.
                                        > > > > >
                                        > > > > >
                                        > > > > >
                                        > > > > > ----------------------------------------------------------
                                        > > > > >
                                        > > > > >
                                        > > > > > CoralTree Systems Limited
                                        > > > > > 25 Barnes Wallis Road
                                        > > > > > Segensworth East, Fareham
                                        > > > > > PO15 5TT
                                        > > > > >
                                        > > > > > Company Registration Number 5021022.
                                        > > > > > Registered Office:
                                        > > > > > 12-14 Carlton Place
                                        > > > > > Southampton, UK
                                        > > > > > SO15 2EA
                                        > > > > > VAT Registration Number 834 1020 74.
                                        > > > > >
                                        > > > > >
                                        > > > > > [Non-text portions of this message have been removed]
                                        > > > > >
                                        > > > >
                                        > > > > [Non-text portions of this message have been removed]
                                        > > > >
                                        > > > >
                                        > > > >
                                        > > >
                                        > > >
                                        > > > [Non-text portions of this message have been removed]
                                        > > >
                                        > >
                                        > >
                                        > > ________________________________
                                        > > NOTICE: The information in this electronic mail transmission is intended by CoralTree Systems Ltd for the use of the named individuals or entity to which it is directed and may contain information that is privileged or otherwise confidential. If you have received this electronic mail transmission in error, please delete it from your system without copying or forwarding it, and notify the sender of the error by reply email or by telephone, so that the sender's address records can be corrected.
                                        > >
                                        > >
                                        > >
                                        > > ----------------------------------------------------------
                                        > >
                                        > >
                                        > > CoralTree Systems Limited
                                        > > 25 Barnes Wallis Road
                                        > > Segensworth East, Fareham
                                        > > PO15 5TT
                                        > >
                                        > > Company Registration Number 5021022.
                                        > > Registered Office:
                                        > > 12-14 Carlton Place
                                        > > Southampton, UK
                                        > > SO15 2EA
                                        > > VAT Registration Number 834 1020 74.
                                        > >
                                        > >
                                        > > [Non-text portions of this message have been removed]
                                        > >
                                        >


                                        ________________________________
                                        NOTICE: The information in this electronic mail transmission is intended by CoralTree Systems Ltd for the use of the named individuals or entity to which it is directed and may contain information that is privileged or otherwise confidential. If you have received this electronic mail transmission in error, please delete it from your system without copying or forwarding it, and notify the sender of the error by reply email or by telephone, so that the sender's address records can be corrected.



                                        --------------------------------------------------------------------------------


                                        CoralTree Systems Limited
                                        25 Barnes Wallis Road
                                        Segensworth East, Fareham
                                        PO15 5TT

                                        Company Registration Number 5021022.
                                        Registered Office:
                                        12-14 Carlton Place
                                        Southampton, UK
                                        SO15 2EA
                                        VAT Registration Number 834 1020 74.


                                        [Non-text portions of this message have been removed]
                                      Your message has been successfully submitted and would be delivered to recipients shortly.