Loading ...
Sorry, an error occurred while loading the content.

Topics List

PiFox on the Rasberry pi 2

(8)
I didn't know anything like pifox was available, but I love the idea!! I hope you get it working, I would like to make one too! 73 Carol KK4CWT On Aug 28,
Carol Murray
8
posts
2:44 PM

Help with PI and TNC-PI

(10)
There are no jumpers on any PI board. The TNC-PI board has 2 jumpers on it. they have to be in place to initially configure the TNC for I2C ... On Thu,
David Cooley
10
posts
8:36 AM

Soundmodem: Use GPIO Pin for PTT

(19)
You betcha! Attached is the circuit diagram a friend came up with for me, and I implemented on a breadboard.  After looking at how the GPIO pins work with the
Rob Ogilvie
19
posts
8:07 AM

Panadapter & PI 2

(3)
Thks Robert VA3BXG (RAC CEC) Emergency Coordinator York Region EmComm / ARES BlackBerry 10 From: Mike Murphree mike@tropo.org [Raspberry_Pi_4-Ham_RADIO] Sent:
va3bxg
3
posts
Aug 26

Bluetooth proximity lock controller

(4)
Hello Simon! Please see my on-list reply to Michael with a couple of relevant code snippets included. If you want to have a go at putting one of these together
Pete Mundy
4
posts
Aug 25

Is Raspberry-pi ready for full blown version of Windows 8+?

(14)
... It doesn’t look like its an X86 processor…. ... The “Modern” Microsoft Compilers (i.e. the .NET compilers, so anything written since 2003)
Dave G4UGM
14
posts
Aug 24

Original (early) TNC-Pi board on RPi2 ?

(6)
Only the first 10 pins on the connector are important to the TNC-PI. You can use an IDF ribbon cable that is 2x5 to connect the boards. I hacked up the
tadd59
6
posts
Aug 23

APRS Receiver/TNC board for the Raspberry Pi

(14)
M = 1,000,000 m = 1/1000 Ham frequencies are specified in Megahertz, MHz. I believe this subtlety was at the basis of the exchange earlier about hams being
Vance Campbell
14
posts
Aug 13

connecting to LCD display and what ever.

(8)
... Hi Eric, My apologies, I must have misunderstood your question when you said: "What is the best way to use a raspberry pi to connect to your own
Pete Mundy
8
posts
Aug 11

unsubscribing

(11)
Let’s try not to call people bad things for no good reason. I’m not really sure he was disparaging the the Raspberry_Pi_4-Ham_RADIO group, or any other.
Tadd Torborg
11
posts
Aug 6

Raspberry Pi Read Only/Write Protection Lock

(6)
I've always had good luck using "Active Kill Disk" to refresh SD cards. The freeware version will write zeros to an entire drive (what we used to call a low
Neil Goldstein
6
posts
Aug 2

How do you update model A?

(3)
Another option I use is a 3 port USB hub with a Ethernet port on the end. They are cheap on eBay and I use them for my A+ as well as the Windows Tablets I
Ronny Julian
3
posts
Jul 31

Cannot get i2c to work

(9)
I wonder if dtparam is what sudo raspi-config changes in the Advanced I2C menus. Tadd Tadd Torborg tadd@mac.com
Tadd Torborg
9
posts
Jul 29

Configuring ax25 properly

(8)
James, I think you pose a good question.  I can not talk intelligently about JNOS, other than I began a node and was quickly overwhelmed. However, before the
Jeffrey Hardy
8
posts
Jul 18

Re: [Raspberry_Pi_4-Ham_RADIO] TNC-black

(5)
Thanks for your response. Do you got a screen connected to the BBB? ... From: "'John Wiseman' john.wiseman@cantab.net [Raspberry_Pi_4-Ham_RADIO]"
tojrortizpr@yahoo.com
5
posts
Jul 17
View First Topic Go to View Last Topic
Loading 1 - 15 of total 15 topics