Loading ...
Sorry, an error occurred while loading the content.

Re: XASTIR USB WX Dongle Device Name

Expand Messages
  • kb4jhu
    Thanks. Used that command and found no ttyUSB* listed. I changed out USB Hub. Same results no ttyUSB* found. Finally changed out USB dongle. Yep...
    Message 1 of 8 , Jul 28 3:11 PM
    • 0 Attachment
      Thanks. Used that command and found no ttyUSB* listed. I changed out USB Hub. Same results no ttyUSB* found.

      Finally changed out USB dongle. Yep... Prolific driver loaded and assigned ttyUSB0. Got it working...

      Wx station is KB4JHU-15.

      Thanks for all the help!

      -Michael KB4JHU

      --- In Raspberry_Pi_4-Ham_RADIO@yahoogroups.com, John Hays <john@...> wrote:
      >
      > Unplug
      >
      > ls /dev/tty*
      >
      > Plug in
      >
      > ls /dev/try*
      >
      > see if new tty device.
      >
      > Sent from my iPhone
      >
    • Ray Wells
      Michael, This is what I see on my system when I attached an usb/rs232 device. For convenience I did this on my Dell desktop system but the result on the Pi
      Message 2 of 8 , Jul 28 4:59 PM
      • 0 Attachment
        Michael,

        This is what I see on my system when I attached an usb/rs232 device. For convenience I did this on my Dell desktop system but the result on the Pi would be very similar, especially the line in syslog about the device being attached to /dev/ttyUSB(#)

        vk2tv@gizmo ~ $ lsusb <device not attached>
        Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
        Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
        Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
        Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
        Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
        Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
        Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
        vk2tv@gizmo ~ $

        vk2tv@gizmo ~ $ lsusb <device attached>
        Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
        Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
        Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
        Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
        Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
        Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
        Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
        Bus 004 Device 002: ID 0557:2008 ATEN International Co., Ltd UC-232A Serial Port [pl2303]
        vk2tv@gizmo ~ $

        vk2tv@gizmo ~ $ lsmod
        Module                  Size  Used by
        pl2303                 17993  0
        usbserial              47107  1 pl2303

        <list severely trimmed to save space>
        vk2tv@gizmo ~ $

        From the end of /var/log/syslog ...

        Jul 29 09:41:56 gizmo kernel: [ 3121.984016] usb 4-2: new full speed USB device number 4 using uhci_hcd
        Jul 29 09:41:56 gizmo mtp-probe: checking bus 4, device 4: "/sys/devices/pci0000:00/0000:00:1a.1/usb4/4-2"
        Jul 29 09:41:56 gizmo kernel: [ 3122.205095] pl2303 4-2:1.0: pl2303 converter detected
        Jul 29 09:41:56 gizmo kernel: [ 3122.217108] usb 4-2: pl2303 converter now attached to ttyUSB0
        Jul 29 09:41:56 gizmo mtp-probe: bus: 4, device: 4 was not an MTP device

        Did you check lsmod to see if the module is loaded?

        Ray vk2tv

        On 29/07/13 01:04, kb4jhu wrote:
         

        Ray,

        Took your suggestion and booted up and plugin the dongle. Looks like it loaded as USB device number 5:

        /var/log/syslog:
        usb 1-1.2: new full-speed USB device number 5 using dwc_otg
        usb 1-1.2: New USB device found, idVendor=110a, idProduct=1110
        usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
        usb 1-1.2: Product: UPort 1110
        1-1.2: Manufacturer: Moxa Technologies Co., Ltd.
        usb 1-1.2: SerialNumber: 000404
        checking bus 1, device 5: "/sys/devices/platform/bcm2708_usb/usb1/1-1/1-1.2"
        bus: 1, device: 5 was not an MTP device

        pi@raspberrypi ~ $ lsusb
        Bus 001 Device 002: ID 0424:9512 Standard Microsystems Corp.
        Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
        Bus 001 Device 003: ID 0424:ec00 Standard Microsystems Corp.
        Bus 001 Device 005: ID 110a:1110 Moxa Technologies Co., Ltd.
        Bus 001 Device 004: ID 04d9:2519 Holtek Semiconductor, Inc.

        pi@raspberrypi ~ $ lsusb -t
        1-1.2:1.0: No such file or directory
        /: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=dwc_otg/1p, 480M
        |__ Port 1: Dev 2, If 0, Class=hub, Driver=hub/3p, 480M
        |__ Port 1: Dev 3, If 0, Class=vend., Driver=smsc95xx, 480M
        |__ Port 2: Dev 5, If 0, Class=vend., Driver=, 12M
        |__ Port 3: Dev 4, If 0, Class=HID, Driver=usbhid, 1.5M
        |__ Port 3: Dev 4, If 1, Class=HID, Driver=usbhid, 1.5M

        pi@raspberrypi ~ $ lsusb -s 1:5
        Bus 001 Device 005: ID 110a:1110 Moxa Technologies Co., Ltd.

        Bus 001 Device 005: ID 110a:1110 Moxa Technologies Co., Ltd.
        Couldn't open device, some information will be missing
        Device Descriptor:
        bLength 18
        bDescriptorType 1
        bcdUSB 2.00
        bDeviceClass 255 Vendor Specific Class
        bDeviceSubClass 0
        bDeviceProtocol 0
        bMaxPacketSize0 8
        idVendor 0x110a Moxa Technologies Co., Ltd.
        idProduct 0x1110
        bcdDevice 2.00
        iManufacturer 1
        iProduct 2
        iSerial 3
        bNumConfigurations 1
        Configuration Descriptor:
        bLength 9
        bDescriptorType 2
        wTotalLength 25
        bNumInterfaces 1
        bConfigurationValue 1
        iConfiguration 0
        bmAttributes 0xa0
        (Bus Powered)
        Remote Wakeup
        MaxPower 100mA
        Interface Descriptor:
        bLength 9
        bDescriptorType 4
        bInterfaceNumber 0
        bAlternateSetting 0
        bNumEndpoints 1
        bInterfaceClass 255 Vendor Specific Class
        bInterfaceSubClass 0
        bInterfaceProtocol 0
        iInterface 0
        Endpoint Descriptor:
        bLength 7
        bDescriptorType 5
        bEndpointAddress 0x01 EP 1 OUT
        bmAttributes 2
        Transfer Type Bulk
        Synch Type None
        Usage Type Data
        wMaxPacketSize 0x0040 1x 64 bytes
        bInterval 0

        Driver name is too long for the WX Serial device of: /sys/devices/platform/bcm2708_usb/usb1/1-1/1-1.2

        Also tried /dev/ttyUSB5 as well as the device name with no luck. Other suggestions??

        -Michael KB4JHU

        --- In Raspberry_Pi_4-Ham_RADIO@yahoogroups.com, Ray Wells <vk2tv@...> wrote:
        >
        > Leave the device unplugged and boot the Pi. Plug the device in and have
        > a look towards the end of /var/log/syslog. If the device was recognised
        > you should see reference to the device and /dev/ttyUSB# where # is the
        > number allocated - ttyUSB1, etc.
        >
        > Ray vk2tv
        >
        > On 28/07/13 11:57, kb4jhu wrote:
        > >
        > > I have a Raspberry Pi running XASTIR using the TNC-PI. I have the
        > > system working with APRS and now desire to connect my Peet Brothers
        > > Altermeter 800 serial weather station to XASTIR.
        > >
        > > I am having a problem finding the ttyUSB port that is assigned. I have
        > > setup the "serial WX" under Interface Control/configure WX Port. Can
        > > anyone help me figure out the "weather station device" for the USB dongle?
        > >
        > > --------------------------------
        > >
        > > Per the var/log/syslog states:
        > > usb 1-1.2: new full-speed USB device number 4 using dwc_otg
        > > usb 1-1.2: New USB device found, idVendor=110a, idProduct=1110
        > > usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
        > > usb 1-1.2: Product: UPort 1110
        > > Manufacturer: Moxa Technologies Co., Ltd.
        > > usb 1-1.2: SerialNumber: 000404
        > >
        > > -----------------------------------------------------
        > >
        > > The Dongle is a Moxa UPort 1110 so the system loaded the driver.
        > >
        > > Now the part I get confused. What /dev/ttyUSB4? is needed for "weather
        > > station device" I have tried several commands to include ls -l
        > > /dev/USB* with no luck finding the /dev for the serial USB dongle.
        > >
        > > Any help is appreciated.
        > >
        > > Michael KB4JHU
        > >
        > >
        >


      • Wolfgang
        Hello , I am trying to get KLOG to work. Things work well, but I only can not get a connection with hamlib. I use the same parameters as for other programs
        Message 3 of 8 , Jul 29 12:41 AM
        • 0 Attachment
          Hello ,
          I am trying to get KLOG to work. Things work well, but I only can not
          get a connection with hamlib.
          I use the same parameters as for other programs (like GRIG, FLDIGI):

          300msec
          FT-857
          /dev/ttyUSB0
          38400

          But I always get a message saying that KLOG can not establish a
          connection to my transceiver.

          What am I doing wrong??

          73, Wolfgang, dl7nb
        • The Silver Fox
          Try lsusb. From: Raspberry_Pi_4-Ham_RADIO@yahoogroups.com [mailto:Raspberry_Pi_4-Ham_RADIO@yahoogroups.com] On Behalf Of kb4jhu Sent: Sunday, July 28, 2013
          Message 4 of 8 , Jul 29 10:36 AM
          • 0 Attachment

            Try lsusb.

             

             

            From: Raspberry_Pi_4-Ham_RADIO@yahoogroups.com [mailto:Raspberry_Pi_4-Ham_RADIO@yahoogroups.com] On Behalf Of kb4jhu
            Sent: Sunday, July 28, 2013 3:12 PM
            To: Raspberry_Pi_4-Ham_RADIO@yahoogroups.com
            Subject: [Raspberry_Pi_4-Ham_RADIO] Re: XASTIR USB WX Dongle Device Name

             

             

            Thanks. Used that command and found no ttyUSB* listed. I changed out USB Hub. Same results no ttyUSB* found.

            Finally changed out USB dongle. Yep... Prolific driver loaded and assigned ttyUSB0. Got it working...

            Wx station is KB4JHU-15.

            Thanks for all the help!

            -Michael KB4JHU

            --- In Raspberry_Pi_4-Ham_RADIO@yahoogroups.com, John Hays <john@...> wrote:
            >
            > Unplug
            >
            > ls /dev/tty*
            >
            > Plug in
            >
            > ls /dev/try*
            >
            > see if new tty device.
            >
            > Sent from my iPhone
            >

          Your message has been successfully submitted and would be delivered to recipients shortly.