Re: [RTrak] RTrak-HAB antenna thoughts
- As Jason has mentioned, WIDE2-1 would be a valid path request. APRS
packets will not activate repeaters, but rather digipeaters.
Digipeaters listen on 144.390 capture packets and forward those
packets back out on the same frequency if a valid path alias is seen
by the digipeater.
As for being in the doughnut hole, the simple solution is to not get
into the hole. If you find yourself in the hole, simply taking you
antenna off the roof and moving it to the side of your vehicle will
work. Obviously this is easiest with a magmount where you can stick it
to the door or other panel. A fold over mount can be folded to aim the
pattern upwards. You can also just bend an antenna over to get the
On 9/6/12, Jason R <lists@...> wrote:
> Glad to hear you have a successful first flight!
>> One thing I'm scratching my head over is that although I configured
>> it for "WIDE2,1" it was not picked up by a single repeater.
> Was this a typo or did you actually put in WIDE2,1?
> If so, that is the problem, the path should have been WIDE2-1. The comma
> would have made the path look like alias WIDE2 and then alias 1 to
> everything on the network. The dash would have made the alias WIDE2-1 and
> that would have given you a single hop.
> Keep in mind, with altitude control, you can have the path be something like
> WIDE2-1 below a certain threshold and then go to no path above that
> threshold. This is a very popular option with balloons since once they
> achieve a certain altitude, there is typically no need for a path and it
> just results in network congestion.
> Jason Rausch - KE4NYV
> RPC Electronics, LLC
> --- In RTrak@yahoogroups.com, "airsix73" <ben.messinger@...> wrote:
>> Just wanted to follow up and let everyone know we pulled off a successful
>> 1st balloon project. The RTrak-HAB performed well. In fact it survived a
>> very hard landing. I didn't mess around with profile or frequency
>> switching just to be safe.
>> One thing I'm scratching my head over is that although I configured it for
>> "WIDE2,1" it was not picked up by a single repeater. I used APRSISCE
>> running on my laptop with a Verizon mobile wifi hotspot to act as an iGate
>> from my chase-vehicle. That worked great, but I'm puzzled that it was
>> ignored by the rest of the APRS community. There are plenty of repeaters
>> around that certainly heard it.
>> I ended up going with a vertical dipole which worked very well until
>> roughly 100,000ft at which point we couldn't get out from under the
>> doughnut and started missing packets. We were roughly 12 miles off to the
>> side, but that was no longer enough distance. Our highest-altitude packet
>> came in at 124k and change. Based on our rate of climb at that point and
>> the time-stamp on the video we hit a bit over 126,000ft roughly 3 minutes
>> Here is a bit of video from the last 1:30 before burst. Thanks for the
>> help with antenna design!
>> --- In RTrak@yahoogroups.com, "airsix73" <ben.messinger@> wrote:
>> > Hello,
>> > I'm preparing my first balloon launch and trying to decide on antennas
>> > for the mobile ground station as well as the balloon. I'm a new ham, and
>> > nervous about keeping a strong enough signal over 25-30 miles with just
>> > 350mw transmit power and random orientation. Suggestions?
>> > For best front-to-back ratio there are some really neat antenna designs
>> > (patch, bi-quad with reflector, yagi, 2 and 3 element quad) but they
>> > aren't very conducive to balloon work!
>> > For those of you who've done this before, what are your recommendations?
>> > I'm sure I'm over-thinking it, so I'd love to hear what others have done
>> > with success.
>> > Thanks!
>> > Ben
> Yahoo! Groups Links
Sent from my mobile device
- Ben KF7VZR (got that from a June 22 message) wrote...
> My documentation says nothing about TX audio level...Deviation is important. If it's too high (within limits) nearby stations
> They've both been played with...
may still be able to decode the tones. Distant ones where your signal
is weaker may not be able to. You have probably heard this on a voice
repeater or even on simplex. A distant and noisy station can be copied
via a repeater if he backs off from the mic. If he starts shouting, the
deviation goes up. More energy is outside the passband of the receiver
and eventually the signal is too noisy to copy or the squelch might
even close. If you are simplex, you can try opening your squelch. If
you are on a repeater, you're out of luck. It's the same with packet.
You are better off having the deviation set properly. It can be done
by ear, but a deviation meter or service monitor would be better.
Lacking one, just crank the deviation all of the way up and then
start turning it down. When it starts to sound quieter, turn it down
some more. It will get you in the ballpark, but checking the actual
deviation would be better.
Perhaps you could check the actual deviation before you change
anything. So... could over-deviation explain why only one iGate
73 es cul - Keith VE7GDH
"I may be lost, but I know exactly where I am!"