RE: [PPLetterpress] Roller Supports
- I agree that the Windmill's adjustment rails solve most if not all
problems that might make roller supports necessary. The only problem
we've ever come across was that two form rollers shrank at different
rates. The solution, of course, was to have them both recovered. Now
we try to get fresh form rollers once a year (our Christmas present
There is, in fact, a frisket attachment for the Windmill. It attaches
to a bar that can be installed below the platen. The bar fits into a
hole that also serves to support the spindle for a roll of foil, if
you're doing foil stamping. The frisket finger is occasionally useful
when running heavy solids close to the edge of the sheet, where the
ink acts as an adhesive. There are accessory "flaps" that can be slid
along the frisket finger. (I'm sure there are official names for
these parts, but I'm too tired to find my manual.)
Indian Hill Press
>I would think the roller support bearers would be moot on a windmill,
>with its excellent roller adjustment rails. Assuming your trucks are
>all the same size and in good condition, of course.
>The rails are more precise and less susceptible to mechanical age/wear,
>I would think, than a carriage-type mechanism. On my Vandercook, I rely
>on gravity to ensure contact between rollers and type. Gravity is
>pretty reliable, but crud, old grease and mechanical misalignment in the
>roller carriage has interfered.
>I would avoid cutting the tympan on a windmill, not only because the
>grippers could snag. Paper will catch on it too, resulting in
>Is there some accessory for using a frisket on the windmill? I can't
>imagine how it would work, but I'm curious.
>Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
- Eric makes a good point. Bearers can be used for a multitude of problems.
They can cause problems with impression if not used properly.
It is always important to understand the relationship between type, ink
rollers, and platen. Any change in either requires a change in the others. I
do more packing behind type than on the platen. I use a variety of type
fonts. to set up reprints of old broadsides. This type will vary in height
quite often. My logic - I want the type to be level on top where it comes in
contact with the ink rollers. I don't care if the feet are even. Packing for
uneven type on the platen serves the same purpose. I like to get the
majority of the type inking evenly, then adjust the feet to bring the type
up to being even. It will now ink even. Platen packing is now obvious.
I print on flatbed presses quite often with hand brayers. I have never found
bearers necessary. I use heavy brayers. The brayer has a large core of metal
which controls the weight and pressure. By using a Brayer with a consistent
weight, the pressure is consistent. I never apply pressure to the brayer,
just allow it to ride over the type or image. Perhaps if I were printing
large expanses of small type I might find a need to support the brayer in
I think that most of this discussion makes the point that all printers need
to completely understand the process, equipment, media, and environment
before applying ink to spatula.
prints by AJ
Point Pleasant, WV
----- Original Message -----
From: "parallel_imp" <Megalonyx@...>
Sent: Monday, September 15, 2008 2:04 PM
Subject: [PPLetterpress] Re: Roller Supports
> --- In PPLetterpress@yahoogroups.com, "Austin Jones" <austin@...> wrote:
>> I just wanted to mention that I use Bearers regularly on my Bobcat
> Press. [. . .]
>> I am just attempting to make the point that Bearers have been around
>> for a long time for use on this type of press.
> Indeed, Austin. I jumped into this thread so people wouldn't get the
> idea that those .918" strips just supported the rollers. The same
> object can be used to compensate for two different problems (in inking
> and impression