Loading ...
Sorry, an error occurred while loading the content.

Re: [PPLetterpress] exposure time/worn out bulbs?

Expand Messages
  • Scott Rubel
    Sorry about that. I had bought tubes here many years ago and when I googled, this company came up, and I didn t look further. I don t know how google brings it
    Message 1 of 12 , Jan 27, 2013
    • 0 Attachment
      Sorry about that. I had bought tubes here many years ago and when I
      googled, this company came up, and I didn't look further. I don't know
      how google brings it up when the code is not listed on their site.

      --Scott

      On Jan 27, 2013, at 6:28 PM, hersomwally wrote:

      > Scott-
      >
      > I checked the link you sent and couldn't find the bulb there. They
      > did have a 15 watt "black light" bulb that would fit and according
      > to the graph emits light in the right range. I wonder if 15w vs.
      > 20w would make a difference?
      >
      > -Wally
      >
      > --- In PPLetterpress@yahoogroups.com, Scott Rubel wrote:
      >>
      >> I hope it's not ballasts. It took me a couple of hours to properly
      >> replace two of them a few years ago. The machine is simple (if it's
      >> like mine), but you still have to be careful and slow as you take it
      >> apart, or you could disconnect wires inadvertently. The more nimble
      >> your fingers, the better.
      >>
      >>
      >> has your bulb, but there are others if you google.
      >>
      >> --Scott
      >>
      >>
      >> On Jan 27, 2013, at 4:44 PM, Gerald Lange wrote:
      >>
      >>> Wally
      >>>
      >>> Do a Google search with the terms bulbs and TL44d25/09n. There are a
      >>> number of suppliers.
      >>>
      >>> If your bulbs have a grayish-brown look to both ends, they are
      >>> likely on
      >>> the wane. But that would indicate that the electrics, especially the
      >>> ballasts are okay. If very dark on one end, not so good.
      >>>
      >>> Did you check to make sure all the bulbs come on at once? or if
      >>> there is
      >>> some staggering problem? You might want to redo the ballasts as
      >>> well.
      >>> The Rocket 5 is an incredible ballast (and fairly low priced) though
      >>> you
      >>> might be in for a major rewiring job.
      >>>
      >>> A long time ago, very early on, I think Harold Kyle mentioned that
      >>> Boxcar was supplying parts for Polimeros. Not sure if that is any
      >>> longer
      >>> the case.
      >>>
      >>> Gerald
      >>>
      >>>
      >>>
      >>> On 1/27/13 4:20 PM, hersomwally wrote:
      >>>> I've finally gotten around to trying our Polimero A4 machine and
      >>>> I've got my first (of many i'm sure) question.
      >>>>
      >>>> I'm using 152sb plates and the info from boxcar says to expose for
      >>>> 2:30-4:00 minutes for a 17-18 on the 21 step scale.
      >>>>
      >>>> 4 minutes only got me to 13 on the scale, so I cranked it up to 7
      >>>> minutes and it still only got it up to 16 on the scale.
      >>>>
      >>>> Is this normal for my machine or does this mean my bulbs are worn
      >>>> out?
      >>>>
      >>>> The bulbs in the machine are tl44d25/09n which is a t8 20watt 18
      >>>> inch. I can't seem to locate any replacements in the US. any idea
      >>>> where to look? (I can't find it on atlanta light bulbs' site).
      >>>>
      >>>> Thanks,
      >>>>
      >>>> Wally
      >>>>
      >>>>
      >>>>
      >>>
      >>>
      >>>
      >>> ------------------------------------
      >>>
      >>> Yahoo! Groups Links
      >>>
      >>>
      >>>
      >>
      >
      >
      >
      >
      > ------------------------------------
      >
      > Yahoo! Groups Links
      >
      >
      >
    • Gerald Lange
      Wally Order from Europe. I have a side business where I am constantly ordering from European countries: Spain, Italy, Poland, Germany, Ireland, Hungary,
      Message 2 of 12 , Jan 27, 2013
      • 0 Attachment
        Wally

        Order from Europe. I have a side business where I am constantly ordering
        from European countries: Spain, Italy, Poland, Germany, Ireland,
        Hungary, Finland, Latvia, etc. (I avoid Russia!!!). Never had a problem
        except for the transit wait.

        Gerald


        On 1/27/13 6:24 PM, hersomwally wrote:
        > I searched google with every variation of terms with that part number and could only find suppliers in Europe.
        >
        > The bulbs actually look pretty good. No discoloration to speak of. All the lights come on at the same time and almost instantly, so hopefully that means the ballasts are OK.
        >
        >
        > --- In PPLetterpress@yahoogroups.com, Gerald Lange wrote:
        >> Wally
        >>
        >> Do a Google search with the terms bulbs and TL44d25/09n. There are a
        >> number of suppliers.
        >>
        >> If your bulbs have a grayish-brown look to both ends, they are likely on
        >> the wane. But that would indicate that the electrics, especially the
        >> ballasts are okay. If very dark on one end, not so good.
        >>
        >> Did you check to make sure all the bulbs come on at once? or if there is
        >> some staggering problem? You might want to redo the ballasts as well.
        >> The Rocket 5 is an incredible ballast (and fairly low priced) though you
        >> might be in for a major rewiring job.
        >>
        >> A long time ago, very early on, I think Harold Kyle mentioned that
        >> Boxcar was supplying parts for Polimeros. Not sure if that is any longer
        >> the case.
        >>
        >> Gerald
        >>
        >>
        >>
        >> On 1/27/13 4:20 PM, hersomwally wrote:
        >>> I've finally gotten around to trying our Polimero A4 machine and I've got my first (of many i'm sure) question.
        >>>
        >>> I'm using 152sb plates and the info from boxcar says to expose for 2:30-4:00 minutes for a 17-18 on the 21 step scale.
        >>>
        >>> 4 minutes only got me to 13 on the scale, so I cranked it up to 7 minutes and it still only got it up to 16 on the scale.
        >>>
        >>> Is this normal for my machine or does this mean my bulbs are worn out?
        >>>
        >>> The bulbs in the machine are tl44d25/09n which is a t8 20watt 18 inch. I can't seem to locate any replacements in the US. any idea where to look? (I can't find it on atlanta light bulbs' site).
        >>>
        >>> Thanks,
        >>>
        >>> Wally
        >>>
        >>>
        >>>
        >
      • Jonathan Jarvis
        I use a god company called Pomeroy Press room Products in Uk  who supply parts for Pre-press platemakers, very good people to work with maybe they can help
        Message 3 of 12 , Feb 1, 2013
        • 0 Attachment
          I use a god company called Pomeroy Press room Products in Uk  who supply parts for Pre-press platemakers, very good people to work with maybe they can help

          --- On Mon, 28/1/13, Gerald Lange <Bieler@...> wrote:

          From: Gerald Lange <Bieler@...>
          Subject: Re: [PPLetterpress] Re: exposure time/worn out bulbs?
          To: PPLetterpress@yahoogroups.com
          Date: Monday, 28 January, 2013, 2:48

           

          Wally

          Order from Europe. I have a side business where I am constantly ordering
          from European countries: Spain, Italy, Poland, Germany, Ireland,
          Hungary, Finland, Latvia, etc. (I avoid Russia!!!). Never had a problem
          except for the transit wait.

          Gerald

          On 1/27/13 6:24 PM, hersomwally wrote:
          > I searched google with every variation of terms with that part number and could only find suppliers in Europe.
          >
          > The bulbs actually look pretty good. No discoloration to speak of. All the lights come on at the same time and almost instantly, so hopefully that means the ballasts are OK.
          >
          >
          > --- In PPLetterpress@yahoogroups.com, Gerald Lange wrote:
          >> Wally
          >>
          >> Do a Google search with the terms bulbs and TL44d25/09n. There are a
          >> number of suppliers.
          >>
          >> If your bulbs have a grayish-brown look to both ends, they are likely on
          >> the wane. But that would indicate that the electrics, especially the
          >> ballasts are okay. If very dark on one end, not so good.
          >>
          >> Did you check to make sure all the bulbs come on at once? or if there is
          >> some staggering problem? You might want to redo the ballasts as well.
          >> The Rocket 5 is an incredible ballast (and fairly low priced) though you
          >> might be in for a major rewiring job.
          >>
          >> A long time ago, very early on, I think Harold Kyle mentioned that
          >> Boxcar was supplying parts for Polimeros. Not sure if that is any longer
          >> the case.
          >>
          >> Gerald
          >>
          >>
          >>
          >> On 1/27/13 4:20 PM, hersomwally wrote:
          >>> I've finally gotten around to trying our Polimero A4 machine and I've got my first (of many i'm sure) question.
          >>>
          >>> I'm using 152sb plates and the info from boxcar says to expose for 2:30-4:00 minutes for a 17-18 on the 21 step scale.
          >>>
          >>> 4 minutes only got me to 13 on the scale, so I cranked it up to 7 minutes and it still only got it up to 16 on the scale.
          >>>
          >>> Is this normal for my machine or does this mean my bulbs are worn out?
          >>>
          >>> The bulbs in the machine are tl44d25/09n which is a t8 20watt 18 inch. I can't seem to locate any replacements in the US. any idea where to look? (I can't find it on atlanta light bulbs' site).
          >>>
          >>> Thanks,
          >>>
          >>> Wally
          >>>
          >>>
          >>>
          >

        • Jonathan Jarvis
          good company..........! ... From: Jonathan Jarvis Subject: Re: [PPLetterpress] Re: exposure time/worn out bulbs? To:
          Message 4 of 12 , Feb 1, 2013
          • 0 Attachment
            good company..........!

            --- On Fri, 1/2/13, Jonathan Jarvis <jonathanjeclipse@...> wrote:

            From: Jonathan Jarvis <jonathanjeclipse@...>
            Subject: Re: [PPLetterpress] Re: exposure time/worn out bulbs?
            To: PPLetterpress@yahoogroups.com
            Date: Friday, 1 February, 2013, 10:51

             

            I use a god company called Pomeroy Press room Products in Uk  who supply parts for Pre-press platemakers, very good people to work with maybe they can help

            --- On Mon, 28/1/13, Gerald Lange <Bieler@...> wrote:

            From: Gerald Lange <Bieler@...>
            Subject: Re: [PPLetterpress] Re: exposure time/worn out bulbs?
            To: PPLetterpress@yahoogroups.com
            Date: Monday, 28 January, 2013, 2:48

             

            Wally

            Order from Europe. I have a side business where I am constantly ordering
            from European countries: Spain, Italy, Poland, Germany, Ireland,
            Hungary, Finland, Latvia, etc. (I avoid Russia!!!). Never had a problem
            except for the transit wait.

            Gerald

            On 1/27/13 6:24 PM, hersomwally wrote:
            > I searched google with every variation of terms with that part number and could only find suppliers in Europe.
            >
            > The bulbs actually look pretty good. No discoloration to speak of. All the lights come on at the same time and almost instantly, so hopefully that means the ballasts are OK.
            >
            >
            > --- In PPLetterpress@yahoogroups.com, Gerald Lange wrote:
            >> Wally
            >>
            >> Do a Google search with the terms bulbs and TL44d25/09n. There are a
            >> number of suppliers.
            >>
            >> If your bulbs have a grayish-brown look to both ends, they are likely on
            >> the wane. But that would indicate that the electrics, especially the
            >> ballasts are okay. If very dark on one end, not so good.
            >>
            >> Did you check to make sure all the bulbs come on at once? or if there is
            >> some staggering problem? You might want to redo the ballasts as well.
            >> The Rocket 5 is an incredible ballast (and fairly low priced) though you
            >> might be in for a major rewiring job.
            >>
            >> A long time ago, very early on, I think Harold Kyle mentioned that
            >> Boxcar was supplying parts for Polimeros. Not sure if that is any longer
            >> the case.
            >>
            >> Gerald
            >>
            >>
            >>
            >> On 1/27/13 4:20 PM, hersomwally wrote:
            >>> I've finally gotten around to trying our Polimero A4 machine and I've got my first (of many i'm sure) question.
            >>>
            >>> I'm using 152sb plates and the info from boxcar says to expose for 2:30-4:00 minutes for a 17-18 on the 21 step scale.
            >>>
            >>> 4 minutes only got me to 13 on the scale, so I cranked it up to 7 minutes and it still only got it up to 16 on the scale.
            >>>
            >>> Is this normal for my machine or does this mean my bulbs are worn out?
            >>>
            >>> The bulbs in the machine are tl44d25/09n which is a t8 20watt 18 inch. I can't seem to locate any replacements in the US. any idea where to look? (I can't find it on atlanta light bulbs' site).
            >>>
            >>> Thanks,
            >>>
            >>> Wally
            >>>
            >>>
            >>>
            >

          • Mª Dolores Jiménez Mondragón
            Somebody can give us details about a Spanish seller of bulbs for platemakers? Thank you and regards, Lola ** I use a god company called Pomeroy Press room
            Message 5 of 12 , Feb 1, 2013
            • 0 Attachment

              Somebody can give us details about a Spanish seller of bulbs for platemakers?

              Thank you and regards,

              Lola

               

              I use a god company called Pomeroy Press room Products in Uk  who supply parts for Pre-press platemakers, very good people to work with maybe they can help

              --- On Mon, 28/1/13, Gerald Lange <Bieler@...> wrote:

              From: Gerald Lange <Bieler@...>
              Subject: Re: [PPLetterpress] Re: exposure time/worn out bulbs?
              To: PPLetterpress@yahoogroups.com
              Date: Monday, 28 January, 2013, 2:48

               

              Wally

              Order from Europe. I have a side business where I am constantly ordering
              from European countries: Spain, Italy, Poland, Germany, Ireland,
              Hungary, Finland, Latvia, etc. (I avoid Russia!!!). Never had a problem
              except for the transit wait.

              Gerald

              On 1/27/13 6:24 PM, hersomwally wrote:
              > I searched google with every variation of terms with that part number and could only find suppliers in Europe.
              >
              > The bulbs actually look pretty good. No discoloration to speak of. All the lights come on at the same time and almost instantly, so hopefully that means the ballasts are OK.
              >
              >
              > --- In PPLetterpress@yahoogroups.com, Gerald Lange wrote:
              >> Wally
              >>
              >> Do a Google search with the terms bulbs and TL44d25/09n. There are a
              >> number of suppliers.
              >>
              >> If your bulbs have a grayish-brown look to both ends, they are likely on
              >> the wane. But that would indicate that the electrics, especially the
              >> ballasts are okay. If very dark on one end, not so good.
              >>
              >> Did you check to make sure all the bulbs come on at once? or if there is
              >> some staggering problem? You might want to redo the ballasts as well.
              >> The Rocket 5 is an incredible ballast (and fairly low priced) though you
              >> might be in for a major rewiring job.
              >>
              >> A long time ago, very early on, I think Harold Kyle mentioned that
              >> Boxcar was supplying parts for Polimeros. Not sure if that is any longer
              >> the case.
              >>
              >> Gerald
              >>
              >>
              >>
              >> On 1/27/13 4:20 PM, hersomwally wrote:
              >>> I've finally gotten around to trying our Polimero A4 machine and I've got my first (of many i'm sure) question.
              >>>
              >>> I'm using 152sb plates and the info from boxcar says to expose for 2:30-4:00 minutes for a 17-18 on the 21 step scale.
              >>>
              >>> 4 minutes only got me to 13 on the scale, so I cranked it up to 7 minutes and it still only got it up to 16 on the scale.
              >>>
              >>> Is this normal for my machine or does this mean my bulbs are worn out?
              >>>
              >>> The bulbs in the machine are tl44d25/09n which is a t8 20watt 18 inch. I can't seem to locate any replacements in the US. any idea where to look? (I can't find it on atlanta light bulbs' site).
              >>>
              >>> Thanks,
              >>>
              >>> Wally
              >>>
              >>>
              >>>
              >

            Your message has been successfully submitted and would be delivered to recipients shortly.