No. I am testing the leads that would plug to the drive while disconnected.
I have another enclosure I can throw the drive in. I don't think it's the drive. I think at this point it's a power issue. I tested the voltage on the other enclosure and got the same 5+ and 12+ that you did. So I am wondering now if it's the power supply. Unfortunately the supply not only powers the drive but the board as well so it would be tricky putting a different supply in place. The one in the LS is a small module with a number of leads coming off to supply board power as well as drive power.
If anyone has a linkstation power supply that is no longer needed. I may be interested I'm it.
--- In LinkStation_ General@yahoogro ups.com, Joseph McLaughlin <jwm8351@... > wrote:
> Two things - are you testing when the devices are connected?
> Do you have access to another power supply
> My first test would be to replace the power supply (I have a box full of them for pc's)
> I am concerned about the 11.6 reading-
> I just tested something and I got 5+ and 12+ (in stand alone mode) + meaning a little bit more than
> If the problem is 12 volt side the cap you mention is probably NOT the problem
> Does it smell burnt?
> ____________ _________ _________ __
> From: scottgriz <griz@...>
> To: LinkStation_ General@yahoogro ups.com
> Sent: Saturday, March 14, 2009 7:10:11 PM
> Subject: [LinkStation_ General] Re: Linkstaion Failure :(
> Hi Joe.
> Thanks for the reply. I am getting 11.63v from the orange wire. It's not yellow on mine. And 5.17v on the red wire. That is straight off the power supply which tells me the power supply us fine. However, when I measure at the 4pin power connector to the HD. I am only getting 5.3v on the orange and 3.24v on the red plus the voltage continuously drop by .01v about every second. I'm thinking the problem is on the main board. Could it be a capacitor causing this? There is one about the size if a dime labeled 5.5v on the board. I'm willing to try whatever I need to revive it. The data was only backup so I am not worried. Its more that I can use the 250gb of space and would rather not spend money on a new one.
> Thanks again.
> --- In LinkStation_ General@yahoogro ups.com, Joseph McLaughlin <jwm8351@ > wrote:
> > 1) I do not know what kind of hard drive you have - it could be an IDE with a 4 pin power and 40 pin cable.
> > if so the yellow cable should be 12v to the black cable - both black cables should be ground - the red cable should be 5 volts.
> > If the red is 12 and the yellow is 5 I read my book wrong.
> > Are you windows or linux the box/drive is linux
> > Evaluate your needs first - you can get a lan based NAS (up to 3 TB) with raid options
> > a dns-321 with a 500 gig hard drive is $205
> > it is under $400.00 with 2 1.5TB drives.
> > (((tiger direct) just a customer))
> > But if your needs are met with the 250 - good luck
> > I think you can also replace the drive with a larger size.
> > I would run spin rite on the drive to check for errors before a reformat.
> > If you are close to Michigan I would be able to help.
> > Joe
> > ____________ _________ _________ __
> > From: scottgriz <griz@>
> > To: LinkStation_ General@yahoogro ups.com
> > Sent: Friday, March 13, 2009 1:40:03 PM
> > Subject: [LinkStation_ General] Linkstaion Failure :(
> > I have an HD-HG250LAN which went belly up. I'm thinking it might have been an overheat issue and blew something. I came home one day and it was off. Every attempt to restart it was unsuccessful. I opened it up and found it had some dust in the vents but it wasn't all that bad.
> > Now, when I press the power button, the blue light on the front blinks rapidly and I hear a tick-tick-tick- tick sound. The drive sounds like it wants to spin up, but then spins back down, same with the fan. The tick sound doesn't appear to be coming from the drive. It doesn't sound like the drive head click we are all familiar with. It sounds more electronic.
> > Does anyone know the output voltages that I should be reading on the power supply so that I can test that and eliminate (or confirm) that as a problem? I put a meter to it and got 5v in a couple places but I am not sure what all the readings should be. I hate to scrap the unit, but at this point I don't know what else to do. I have it completely apart now and just trying to think of what to check next. If I pull the drive and were to put it in another system and clean format it, will I be destroying any possibility of using this as a linkstation again or is it possible to write the software back to it later? I'm thinking I would like to rule out the drive by putting it in an external case, but I am not sure I would even be able to access it without first formatting it.
> > Any thoughts on this problem would be greatly appreciated.
> > Thanks,
> > Scott