Loading ...
Sorry, an error occurred while loading the content.

Topics List

Rico engine house? Monster Modelworks considering a kit

(13)
Sounds like an interesting project, are there any dimensioned architectural drawing that can be obtained? I might be up to the challenge. Ole... aka Geo... @
Ole Olson
13
posts
7:50 PM

Re: [RGS] RGS Three Way Stub Tie Configuration

(7)
I have the whole set, Duncan. I was responding to the location and length of ties for a three way stub switch. The diagram in Jerry's manual might be
Russ Norris
7
posts
5:51 PM

Private messages - how to?

(17)
When I was a kid working in my fathers grocery store we, went to the train depot every Thursday morning to meet the local and pick up hanging beef and pigs
Vic
17
posts
1:21 PM

RGS Three Way Stub Tie Configuration

(6)
The most important thing is to get ties all the way across 10' downstream of the pair of frogs. After that you can 'stitch' ties in-between each other if you
jefehon3
6
posts
12:26 PM

Erie limited brass?

(5)
Sorry I'm a bit late to this one, but I'll add a few experiences of the Erie RGS 20. 1. The Erie RGS 20 is a nice runner, but rather fast. I replaced the
Mick Moignard
5
posts
2:25 AM

Keystone Shays information long

(4)
I wrote Greg offline, but just to remind people -- David Hoffman is not on-line at all. The easiest was to contact him is via phone (601) 888-3016. He prefers
mmattjcoleman
4
posts
May 23

Colorado HOn3 Layout

(6)
New Web page uploaded http://www.modvid.com.au/html/body_mike_mcclure.html http://www.modvid.com.au/html/body_mike_mcclure.html cheers all Mario Rapinett
modvidaustralia
6
posts
May 19

Re: New file uploaded to HOn3

(117)
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the HOn3 group. File : /Doug
HOn3@yahoogroups.com
117
posts
May 19

Tar Paper roofs

(37)
The masking tape roofs on the buildings in the pictures are all 10-12 years. No peeling. I use a good 3M masking tape. Not the colored lo tack stuff. I
tonyk537
37
posts
May 8

HOn3 diesel conversion

(5)
Walter, assuming you have the correct diesel (5 gears visible through the bottom cover of the trucks) there is absolutely no need to cut the printed circuit
utahrex
5
posts
May 7
Craig Palmer KF5JYZ
4
posts
May 6

Blackstone K27 motors

(19)
Hart, It was the connection between Kader, Blackstone and Bachmann that propted me to suggest looking for the motor on the Bachmann site. If memory serves me
szczowicz
19
posts
May 4

Repurposed turntable bridge

(6)
Wes Scan the frontage road, on interstate 70's south side, westwards from the Convulsion road interchange. at high magnification in satellite view. You will
John Stutz
6
posts
May 3

shims/washers

(5)
The Northwest Short line catalog page you seek is http://www.nwsl.com/uploads/chap5_web_04-15.pdf at The bottom of the page you will find the listing of shims
Ole Olson
5
posts
May 2

Pagosa springs combine cupola lantern

(16)
Bill, Time for a slight rebuild of my 0404 then - good thing too, I wasn't really that pleased with what was there before. Many thanks. Mark K Oxford, England.
szczowicz
16
posts
May 1
View First Topic Go to View Last Topic
Loading 1 - 15 of total 15 topics