Loading ...
Sorry, an error occurred while loading the content.

Topics List

no output on g11

(14)
It would appear from those measurements, that U1P is bad. With around 1.5 – 2.0 v pk-pk at it's inputs ( pins 2, 6 .. +/- 10mw ) there should be around 20v
Bruce Greenleaf kf1z
14
posts
6:54 AM

G11 Bias settings and how, Low output power

(20)
An update, Replaced the resistor 56K to 56 ohms.  What a difference!!  Ten watts easily on all bands except 6 meters.Set the default drive values to 48 and
Ray Worrall
20
posts
Aug 24

G11 DIY SMT Assembly Aid

(9)
One point the group should be aware of. There are a number of parts that do not need to be installed (some I would advise - DO NOT install), if you are not
Evan Pallesen
9
posts
Aug 22

G11 Theory of operation

(9)
If you can track down articles on the "Third Method" of SSB generation, such as the excellent ones in RadCom magazine back in the late nineties, they will
Evan Pallesen
9
posts
Aug 22

GPA10 Bias Adjustment Instruction

(15)
Hi Bruce, Yes test button measured 1.08 tip and 1.086 sleeve (center band) relative to base of plug.  Used two meters same results.  Using line out/input
Ray Worrall
15
posts
Aug 19

GSDR hangup

(9)
OK, now seems to be working. At least I'm getting relay clicks. Not sure what was wrong. Thanks for the help Jim...kq3s Sent from my iPad
Jim Painter
9
posts
Aug 16

si570

(6)
thanks for the info Alan much appreciated!
vk2ams
6
posts
Aug 15

Windows 10 GSDR G11 works

(27)
Windows 10 works fine with my ANAN-100D and Hermes-Lite. I don't use VAC though, I use VB-Cable which is a free alternative to VAC that's easier to use and
w3drk
27
posts
Aug 10

[Help!] G59 - Phase 3 Voltage Checks

(7)
frequencies will be no where close.... until after RX is assembled, and you can calibrate Si570 Check R9G and R10G are 270 ohm. Also be sure the neg lead of
Bruce Greenleaf kf1z
7
posts
Aug 9

How I installed USB soundcard and GSDR on Windows 7, 32-bit

(9)
Hello David, WB0QOA I have not tried to install Asus Xonar Essence STX, but my guess would be, that installation is similar to the one described for Xonar U5.
lars_schjelde_petersen
9
posts
Aug 7

GPA10 Toroid winding

(5)
Thanks Evan, yes it’s the first two turns that are the difficult part, that added to the old fingers thick wire and small toroid. Thank you for your advise,
terry2
5
posts
Aug 3

First Time Power Up

(31)
Unable to find a way to disable this internal speaker. Strangely enough, when I plug in a head set to the computer phones jack the sound does not go away. When
artsofyoga
31
posts
Aug 3

G59 firmware

(11)
PLEASE Nick and Andrew You are getting FIRMWARE confused with the Boot file ! Firmware for all radios available freely with software packages. BOOT file for
Bruce Greenleaf kf1z
11
posts
Aug 2

GSDR won't fit on screen vertically

(7)
oh, you didn't say it was a laptop. Unfortunately laptop screens are very limited to what they display. Your best choice then is to click on the button on the
Bruce Greenleaf kf1z
7
posts
Aug 1

Windows 10 compatibility

(13)
I managed to download windows 10 pro both 32 & 64 bit iso's You can download quite easy yourself.... have a read ... Windows 10 ISO ... On Saturday, 1 August
Gary S
13
posts
Aug 1
View First Topic Go to View Last Topic
Loading 1 - 15 of total 15 topics