Loading ...
Sorry, an error occurred while loading the content.

Topics List

G59, GPA10 kits availability

(3)
Hi Bruce, I would like to order a G59/GPA10 case please. -Dan VK5DJW On Thu, 30 Mar 2017, 12:30 PM 'Bruce Greenleaf kf1z' bruce@kf1z.com
Daniel Wiering
3
posts
6:09 PM

GSDR Sotware

(3)
Thanks! Worked like a charm. * A gun is like a parachute. If you need one but don't have it you'll probably never need one again. * On 3/29/2017 11:34 AM,
Ed Borghi
3
posts
Mar 29

G11 startup

(18)
then either change cables going into soundcard ( L to R ) OR In audio tab ( GSDR soundcard settings) Check or un-check the "RX Swap I/Q" box From:
Bruce Greenleaf kf1z
18
posts
Mar 28

GPA10 - unable to test the driver

(3)
Hi Bruce, It is always good to ask those fundamental questions first :) Yes, GPA10 is powered, the 4 wire jumper (control signals from G59 to GPA10) is in
yu1wc
3
posts
Mar 19

Re: G40 - Curious about the extras on pcb

(22)
Hi Bruce, I think it might be my power supply.. it is putting out 14.5vdc! it might of cooked both of those transistors as I put one in and then the other. I
Rob Copeland
22
posts
Mar 18

G40 - Relays,Chokes,toroids, ferrite, trimmers, connectors, switches

(9)
Right on the money Bruce! Thank you it is working the way it is supposed to. J Rob – KF7UZH From: GenesisRadio@yahoogroups.com
Rob Copeland
9
posts
Mar 10

G 59 PTT.

(3)
In GSDR Setup > General > Options ... Is "Disable PTT" box checked, or not ? And in Setup > General > Genesis Config are there any keyer options checked? As
Bruce Greenleaf kf1z
3
posts
Mar 9

G59 PTT

(8)
Thanks Hope your Day gets Better. Rick, kd4dra On 3/6/2017 4:18 PM, 'Bruce Greenleaf kf1z' bruce@kf1z.com
Rick B
8
posts
Mar 7

G59 phase 7 voltage and relay issue.

(4)
Hi. Dan again. Luckily ICB2 checked out fine. I was getting about 300 ohm across the coil of all of the relays except for relay 7 (6M relay). On that relay
danialpadgett
4
posts
Mar 6

Computer cant find my G59.

(5)
Hi, Dan here again. When plugged into USB I continued to get intermittent function and after checking I kept loosing my 16MHz oscillation. I had a spare
danialpadgett
5
posts
Feb 27

ExpertSDR

(7)
HI, In my excitment, I was running Genesis not ExpertSDR. I rebooted the host with the cable disconnected and verified that the USB device had the correct
Michael Jordan
7
posts
Feb 19

For sale is a G3020 Radio/ emu 0202

(5)
Hi Michael, Open the Genesis program. Click on setup, General, Genesis config, under port connection with the pulldown select com 4, then apply save ok. click
Ray Worrall
5
posts
Feb 6

G59 parts HC4028N and crystal 58.180MHz or 58.180KHz

(10)
Bruce replied to me today on the crystal's purpose. "That part of the circuit is the "receive calibrator" All it is is a comb generator, to allow a signal (
pq6gvyspeqqivk5wibazikqg7fsakh7aivmktwbb
10
posts
Feb 6
View First Topic Go to View Last Topic