Loading ...
Sorry, an error occurred while loading the content.

Topics List

FT-897 No transmit

(12)
PEBKAC....problem exists between keyboard and chair! ... KA4KOE
ka4koe
12
posts
Feb 10

CAT control stopped working

(13)
Have you tried a reset? It's my understanding that sometimes the rig "loses control" of the CAT port, and a reset brings it back in line. I don't know if that
kb4mto
13
posts
Feb 6

Programming with CHIRP on Macintosh

(8)
Hey, Chuck, I finally got to attempt this. /dev/cu.usbserial-RTYVKI9W in the CHIRP port and no joy. This is the CAT-62 cable Checked the /dev directory and
Mark L Dallner
8
posts
Feb 1

Yaesu FT-897D in FM mode

(4)
Maybe your TOCO-Filter is defect. The same effect I had with it. Maybe your signal meter works in SSB correct because an other filter is used. At me AM worked,
Klaus_W=c3=b6rner_DL5KV
4
posts
Jan 31

FS: Yaesu MD-100 desk mic for FT897

(7)
I have one, and love it. He is correct though you need to do some ALC settings. I only have it wired for the FT897D so yes it works just fine! On Fri, Jan 29,
Chris Robinson
7
posts
Jan 29

How can I cause the FT-897D to turn ON when I apply 12 volt power?

(12)
Martin, Here you go. http://www.employees.org/~seanc/ft897-897d-tech_sup.pdf Hope it helps, Sean ~ N9ATV Hi Chuck, I have used an FT-857d and FT-897d under
Sean Clark
12
posts
Jan 28

Meter Explanation

(26)
blockquote, div.yahoo_quoted { margin-left: 0 !important; border-left:1px #715FFA solid !important; padding-left:1ex !important; background-color:white
David Bradley
26
posts
Jan 27

question about FT 897D running mobile with Battery packs installed

(9)
My 897D will automatically switch when power-supply is added or shut down , so you may or may not notice a flicker when operating and you gain or loose power
John tf
9
posts
Jan 24

FT-897D Squelch problem...Help!

(5)
From the service manual." Bob w7wo FM Squelch Adjustment r Tune the transceiver to the 144 MHz band in the FM mode. Confirm that the squelch knob is turned
Robert Kalkwarf
5
posts
Jan 24

897 HELP

(53)
Just a suggestion... I'm guessing the main CPU is bad. Typical symptoms: radio draws a few milliamps quiescent when connected to a power supply (after initial
Julius Madey
53
posts
Jan 23

AT-897 Control ??

(8)
The AT-897 push button is a momentary switch. In order to operate it remotely, we added a parallel pair of wires across the switch. They are connected to a
Lew M
8
posts
Jan 23

FT897 Accessory

(7)
Tom, your way is much better but when space is critical or you're in the Army on a hill top in Korea listening to bad guys on the other side, something burns
richard bridges
7
posts
Jan 17

Ceramic TOKO filters

(8)
Hi all Read all infos, i’m not good enouth to explain something on how to work this filter circuit. My filters were green, moisture inside them, or
Unit365
8
posts
Jan 16

LCD Screen hard to read

(10)
Contact this seller to see if they can supply you. http://m.ebay.com.au/itm/181960050981?_mwBanner=1 Others come and go as well.
Darryl Harvey
10
posts
Jan 15

Year 2010 FT897D, Bias settings.

(5)
I think it starts all over again in 2010. I bought a new 857D in 2014 and the serial begins with 3K so I assume it was built Sept 2013. Tom K3TVC From:
Thomas Chesek
5
posts
Jan 15
View First Topic Go to View Last Topic
Loading 1 - 15 of total 15 topics